Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/ Multi-display) › from 2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261009 TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/ Multi-display) J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/ Multi-display)  Clearance Warning ECU Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the clearance warning ECU.

WIRING DIAGRAM

E283774E05
0.677,0.823 1.979,1.01 1.302,0.188 10 false from IG NO.1 Relay 3.177,0.969 4.094,1.135 0.917,0.167 10 false ECU-IG NO.2 5.375,0.781 5.583,0.948 0.208,0.167 10 false IG 5.365,1.323 5.573,1.49 0.208,0.167 10 false E 5.083,1.885 6.042,2.104 0.958,0.219 10 false I9*1, G228*2 5.063,2.083 6.656,2.292 1.594,0.208 10 false Clearance Warning ECU 5.115,0.688 5.323,0.854 0.208,0.167 10 false 1 5.063,1.24 5.271,1.406 0.208,0.167 10 false 30 0.24,2.063 1.833,2.271 1.594,0.208 10 false *1: for 4 Sensor Type 0.25,2.344 1.844,2.552 1.594,0.208 10 false *2: for 8 Sensor Type

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - BATTERY)
a.
E309541E05
1.042,0.271 1.396,0.5 0.354,0.229 1.854,0.26 2.24,0.5 0.385,0.24 0.896,1.74 0.51,1.031 true 1.156,0.313 1.469,0.51 0.313,0.198 10 false I9 1.875,0.302 2.354,0.51 0.479,0.208 10 false G228 1.438,0.323 1.75,0.521 0.313,0.198 10 false *A 2.292,0.323 2.604,0.521 0.313,0.198 10 false *B 0.958,1.667 1.271,1.865 0.313,0.198 10 false IG

Disconnect the clearance warning ECU connector.


b.

Measure the voltage according to the value(s) on the table below.

Standard Voltage:
for 4 Sensor Type
Tester Connection Switch Condition Specified Condition
I9-1 (IG) - Body ground Ignition switch ON 11 to 14 V
I9-1 (IG) - Body ground Ignition switch off Below 1 V

for 8 Sensor Type
Tester Connection Switch Condition Specified Condition
G228-1 (IG) - Body ground Ignition switch ON 11 to 14 V
G228-1 (IG) - Body ground Ignition switch off Below 1 V


Text in Illustration
*A for 4 Sensor Type
*B for 8 Sensor Type
*a Front view of wire harness connector
(to Clearance Warning ECU)



OK

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - BODY GROUND)
a.
E309541E06
1.042,0.271 1.396,0.5 0.354,0.229 1.854,0.26 2.24,0.5 0.385,0.24 2.135,1.698 1.771,1.188 true 1.156,0.313 1.469,0.51 0.313,0.198 10 false I9 1.875,0.302 2.354,0.51 0.479,0.208 10 false G228 1.438,0.323 1.75,0.521 0.313,0.198 10 false *A 2.292,0.323 2.604,0.521 0.313,0.198 10 false *B 2.167,1.698 2.479,1.896 0.313,0.198 10 false E

Disconnect the clearance warning ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 4 Sensor Type
Tester Connection Condition Specified Condition
I9-30 (E) - Body ground Always Below 1 Ω

for 8 Sensor Type
Tester Connection Condition Specified Condition
G228-30 (E) - Body ground Always Below 1 Ω


Text in Illustration
*A for 4 Sensor Type
*B for 8 Sensor Type
*a Front view of wire harness connector
(to Clearance Warning ECU)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR