Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM C

1GD-FTV ENGINE CONTROL  ECD SYSTEM  P0107  Manifold Absolute Pressure / Barometric Pressure Circuit Low Input  P0108  Manifold Absolute Pressure / Barometric Pressure Circuit High Input  


DESCRIPTION

The manifold absolute pressure sensor detects the intake manifold pressure. The ECM determines the basic injection volume and injection advance timing based on the voltage output by the manifold absolute pressure sensor.

The manifold absolute pressure sensor monitors the absolute pressure inside the intake manifold (default is 0 kPa [0 mmHg, 0 in.Hg]). As a result, the ECM controls the air-fuel ratio so that it reaches the proper level under any driving conditions.

A208461E01
0.417,0.406 0.74,0.646 0.323,0.24 10 false V 0.156,0.813 0.594,1.042 0.438,0.229 10 false 3.586 0.167,1.917 0.615,2.135 0.448,0.219 10 false 0.386 1.021,2.323 1.198,2.469 0.177,0.146 10 false 40 2.333,2.323 2.604,2.469 0.271,0.146 10 false 320 0.979,2.656 1.25,2.802 0.271,0.146 10 false 300 0.938,2.802 1.323,3.042 0.385,0.24 10 false (11.8) 2.24,2.792 2.625,3.083 0.385,0.292 10 false (94.5) 2.854,2.771 3.302,3.083 0.448,0.313 10 false (in.Hg) 2.854,2.542 3.302,2.813 0.448,0.271 10 false mmHg 2.833,2.115 3.198,2.313 0.365,0.198 10 false kPa 2.854,2.26 3.24,2.5 0.385,0.24 10 false (abs) 2.24,2.646 2.573,2.792 0.333,0.146 10 false 2400 1.323,3.042 2.25,3.313 0.927,0.271 10 false Air Pressure

P0107
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
2 seconds after engine is started, race engine for 1 second After the engine is started, condition (a) continues for more than 0.5 seconds (1 trip detection logic):
(a) Manifold absolute pressure sensor voltage is 0.1 V or less.
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM



P0108
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
2 seconds after engine is started, race engine for 1 second After the engine is started, condition (a) continues for more than 0.5 seconds (1 trip detection logic):
(a) Manifold absolute pressure sensor voltage is 4.8 V or higher.
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM



Related Data List
DTC No. Data List
P0107
P0108
·

MAP

·

Atmosphere Pressure



HINT:
·

If DTC P0107 and/or P0108 is stored, the following symptoms may appear:

-

Misfire

-

Combustion noise

-

Black smoke

-

White smoke

-

Lack of power


·

When DTC P0107 or P0108 is stored, check the intake manifold pressure by entering the following menus: Powertrain / Engine and ECT / Data List / MAP.

Reference
GTS Displayed Malfunction
22 kPa (165 mmHg, 6.5 in.Hg)
·

Open in VC circuit

·

Open in PIMcircuit

·

Short in PIM circuit


320 kPa (2400 mmHg, 94.5 in.Hg) or higher
·

Open in E circuit





WIRING DIAGRAM

A348539E02
0.51,2.229 2.719,2.427 2.208,0.198 10 false Manifold Absolute Pressure Sensor 0.51,2.042 0.969,2.24 0.458,0.198 10 false C83 1.521,0.469 1.979,0.667 0.458,0.198 10 false VC 1.448,1.042 1.906,1.24 0.458,0.198 10 false PIM 1.594,1.583 2.052,1.781 0.458,0.198 10 false E 5.656,0.469 6.313,0.667 0.656,0.198 10 false VCPM 5.667,1.021 6.125,1.219 0.458,0.198 10 false PIM 5.646,1.583 6.104,1.781 0.458,0.198 10 false EPIM 1.833,0.573 2.292,0.771 0.458,0.198 10 false 3 1.833,1.156 2.292,1.354 0.458,0.198 10 false 2 1.823,1.698 2.281,1.896 0.458,0.198 10 false 1 5.406,0.583 5.667,0.792 0.26,0.208 10 false 28 5.385,1.146 5.875,1.333 0.49,0.188 10 false 18 5.396,1.698 5.677,1.896 0.281,0.198 10 false 19 5.979,2.229 6.51,2.427 0.531,0.198 10 false ECM 5.99,2.042 6.448,2.24 0.458,0.198 10 false C149

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (MAP)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAP.


d.

Read the value.

OK:

Same as the actual atmospheric pressure.


HINT:
·

Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather (high atmospheric pressure, low atmospheric pressure).

·

Also, check "Atmosphere Pressure" in the Data List.





NG

2.CHECK ECM TERMINAL VOLTAGE (VC TERMINAL)

OK

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.CHECK ECM TERMINAL VOLTAGE (VC TERMINAL)
a.
U169124E01
1.49,1.281 1.198,1.698 false 1.948,1.281 2.188,1.688 false 1.094,1.729 1.208,1.885 0.115,0.156 10 false E 2.208,1.698 2.479,1.854 0.271,0.156 10 false VC 0.24,0.219 0.427,0.385 0.188,0.167 10 false *a 0.656,1.094 0.938,1.24 0.281,0.146 10 false C83

Disconnect the manifold absolute pressure sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C83-3 (VC) - C83-1 (E) Engine switch on (IG) 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Manifold Absolute Pressure Sensor)


c.

Reconnect the manifold absolute pressure sensor connector.



OK

3.INSPECT MANIFOLD ABSOLUTE PRESSURE SENSOR (PIM VOLTAGE)

NG

7.CHECK ECM (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)
3.INSPECT MANIFOLD ABSOLUTE PRESSURE SENSOR (PIM VOLTAGE)
a.
U169388E01
0.573,1.646 1.271,2.458 false 0.521,1.635 0.292,2.438 false 0.271,0.927 0.708,1.094 0.438,0.167 10 false C149 0.094,0.031 0.531,0.198 0.438,0.167 10 false *a 0.073,2.458 0.75,2.625 0.677,0.167 10 false 19 (EPIM) 1.208,2.458 1.854,2.625 0.646,0.167 10 false 18 (PIM)

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C149-18 (PIM) - C149-19 (EPIM) Engine switch on (IG) 0.8 to 1.5 V

Text in Illustration
*a Component with harness connected
(ECM)




NG

4.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)

OK

9.REPLACE ECM
4.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C83-2 (PIM) - C149-18 (PIM) Always Below 1 Ω
C83-1 (E) - C149-19 (EPIM) Always Below 1 Ω
C83-2 (PIM) or C149-18 (PIM) - Body ground and other terminals Always 10 kΩ or higher
C83-1 (E) or C149-19 (EPIM) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the manifold absolute pressure sensor connector.


e.

Reconnect the ECM connector.



OK

5.CHECK ECM (CHECK RESISTANCE)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CHECK ECM (CHECK RESISTANCE)
a.
U169125E01
0.638,1.108 0.938,1.265 0.300,0.158 10 C83 1.466,1.263 1.033,1.734 false 1.975,1.275 2.408,1.746 false 0.939,1.755 1.084,1.913 0.145,0.158 10 E 2.328,1.749 2.628,1.907 0.300,0.158 10 VC 0.14,0.114 0.322,0.271 0.182,0.158 10 *a 1.586,1.775 1.886,1.933 0.300,0.158 10 PIM 1.723,1.269 1.724,1.749 false

Disconnect the manifold absolute pressure sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C83-3 (VC) - C83-2 (PIM) Engine switch off No short or open
C83-2 (PIM) - C83-1 (E)


Text in Illustration
*a Front view of wire harness connector
(to Manifold Absolute Pressure Sensor)


c.

Reconnect the manifold absolute pressure sensor connector.



OK

6.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

9.REPLACE ECM
6.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Replace the manifold absolute pressure sensor (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MANIFOLD ABSOLUTE PRESSURE SENSOR>REMOVAL).



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CHECK ECM (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.
U169389E01
0.573,1.698 1.271,2.458 false 0.521,1.646 0.292,2.438 false 0.26,0.927 0.698,1.094 0.438,0.167 10 false C149 0.094,0.031 0.531,0.198 0.438,0.167 10 false *a 0.073,2.458 0.75,2.625 0.677,0.167 10 false 19 (EPIM) 1.208,2.458 2.063,2.625 0.854,0.167 10 false 28 (VCPM)

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C149-28 (VCPM) - C149-19 (EPIM) Engine switch on (IG) 4.5 to 5.5 V

Text in Illustration
*a Component with harness connected
(ECM)




OK

8.REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

9.REPLACE ECM
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPLACE ECM

NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off for 30 seconds or more.


d.

Turn the GTS off.


e.

Turn the engine switch on (IG) for 3 seconds and turn the GTS on.


f.

After the engine is started for 2 seconds, race the engine for 1 second.


g.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


ii.

Input DTC P0107 or P0108.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, race the engine for 1 minute, and then idle the engine for 5 minutes.




NEXT

END