Refer to DTC P007C (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>P007C).
Refer to DTC P0112 (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>P0112).
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| After engine completely warmed up, allow engine to soak for long time (10 hours or more).
Start the engine and idle the engine for 3 minutes or more. |
After the engine is completely warmed up and then allowed to soak for a long time (10 hours or more), the difference in temperature at the intake air temperature sensor and intake air temperature sensor (turbo) after turbocharger after idling for 3 minutes is 25°C (45°F) or higher.
(2 trip detection logic) |
·
Open or short in intake air temperature sensor circuit ·
Open or short in intake air temperature sensor (turbo) circuit ·
Intake air temperature sensor (built into mass air flow meter sub-assembly) ·
Intake air temperature sensor (turbo) ·
ECM ·
Engine off timer (P2610) |
| DTC No. | Data List |
|---|---|
| P011C | ·
Intake Air ·
Intake Air Temp (Turbo) |
Refer to DTC P007C (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>P007C).
Refer to DTC P0112 (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>P0112).
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P011C is output | A |
| DTC P011C and other DTCs are output | B |
A
B
Allow the engine to soak for 1 to 2 hours.
It is not necessary to allow the engine to soak if the engine is cold.
The engine cools faster if the hood is opened.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant temp.
Read the value.
The difference between the displayed value and outside air temperature is below 5°C (9°F).
If the difference between "Coolant Temp" and the outside air temperature is 5°C (9°F) or higher, the heat from the engine affects the intake air temperature sensor, causing an incorrect value to be displayed. In this case, allow the engine to soak again.
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
Read the value.
The difference between the displayed value and outside air temperature is below 25°C (45°F).
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).
Read the value.
The difference between the displayed value and outside air temperature is below 25°C (45°F).
OK
NG
Replace the ECM (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Disconnect the intake air temperature sensor (turbo) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C84-2 - C150-35 (THIA) | Always | Below 1 Ω |
| C84-1 - C150-27 (ETHI) | Always | Below 1 Ω |
| C84-2 or C150-35 (THIA) - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the intake air temperature sensor (turbo) connector.
Reconnect the ECM connector.
OK
NG
Replace the intake air temperature sensor (turbo) (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>REMOVAL).
NEXT
Disconnect the mass air flow meter sub-assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| GTS Connection | Condition | Specified Condition |
|---|---|---|
| C33-4 (THA) - C150-32 (THA) | Always | Below 1 Ω |
| C33-2 (E2G) - C150-24 (EVG) | Always | Below 1 Ω |
| C33-4 (THA) or C150-32 (THA) - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the mass air flow meter sub-assembly connector.
Reconnect the ECM connector.
OK
NG
Replace the mass air flow meter sub-assembly (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL).
If foreign matter is stuck inside the mass air flow meter sub-assembly, the output characteristics of the mass air flow meter sub-assembly may change, resulting in a malfunction.
NEXT
Repair or replace the harness or connector.
NEXT
Allow the engine to soak for 1 to 2 hours.
It is not necessary to allow the engine to soak if the engine is cold.
The engine cools faster if the hood is opened.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant temp.
Read the value.
If the difference between "Coolant Temp" and the outside air temperature is 5°C (9°F) or higher, the heat from the engine affects the intake air temperature sensor, causing an incorrect value to be displayed. In this case, allow the engine to soak again.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air and Intake Air Temp (Turbo).
Read the value.
The difference between the displayed value and outside air temperature is below 25°C (45°F).
NEXT