Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM C

1GD-FTV ENGINE CONTROL  ECD SYSTEM  P2454  Diesel Particulate Filter Pressure Sensor "A" Circuit Low  P2455  Diesel Particulate Filter Pressure Sensor "A" Circuit High  


DESCRIPTION

HINT:
·

For more information on the differential pressure sensor and Diesel Particulate Filter (DPF), refer to the following procedures (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>SYSTEM DESCRIPTION).

·

If P2454 and/or P2455 is present, refer to the DTC chart for DPF system (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>SYSTEM DESCRIPTION).



A128654E15
4.417,1.208 4.229,1.385 false 4.948,1.115 4.875,1.365 4.875,1.365 4.969,1.365 false 4.406,1.167 4.24,1.208 false 5.5,3.042 5.271,2.552 5.271,2.552 5.406,2.552 false 1.302,2.26 0.802,2.917 false 2.76,2.552 2.885,2.917 false 1.302,0.708 2.125,0.885 0.823,0.177 10 false Exhaust Gas 2.917,0.708 3.26,0.875 0.344,0.167 10 false ECM 0.375,2.938 1.448,3.271 1.073,0.333 10 false DPF Catalytic Converter 2.094,2.958 3.823,3.146 1.729,0.188 10 false Differential Pressure Sensor 3.854,0.052 5.708,0.24 1.854,0.188 10 false Property of Output Voltage: 5.01,1.281 5.896,1.448 0.885,0.167 10 false Stores P2455 5.448,2.479 6.354,2.646 0.906,0.167 10 false Stores P2454 4.052,0.635 6.073,0.813 2.021,0.177 10 false Differential Pressure Voltage (V) 4.021,0.938 4.396,1.104 0.375,0.167 10 false 5.000 3.865,1.135 4.24,1.302 0.375,0.167 10 false 4.800 3.865,1.333 4.24,1.5 0.375,0.167 10 false 4.650 4.021,2.396 4.396,2.563 0.375,0.167 10 false 1.530 4.021,2.604 4.396,2.771 0.375,0.167 10 false 0.750 4.021,2.75 4.396,2.917 0.375,0.167 10 false 0.555 4.021,2.896 4.396,3.063 0.375,0.167 10 false 0.400 4.292,3.115 4.396,3.271 0.104,0.156 10 false 0 4.771,3.24 4.875,3.396 0.104,0.156 10 false 0 4.531,3.24 4.708,3.406 0.177,0.167 10 false -5 4.938,3.24 5.229,3.406 0.292,0.167 10 false 20.0 6.479,3.25 6.865,3.417 0.385,0.167 10 false 100.0 4.323,3.427 6.813,3.625 2.49,0.198 10 false Exhaust Gas Differential Pressure (kPa)

The two sensing chambers of the differential pressure sensor are mounted to monitor the pressure before and after the DPF catalytic converter. The sensor itself is not located on the engine assembly in order to reduce the influence of vibration.

The ECM compares the exhaust gas pressure before and after the DPF catalytic converter by monitoring the pressure using the upstream and downstream sensing chambers of the differential pressure sensor. If the difference in pressure exceeds a predetermined level, the ECM judges that the catalytic converter is clogged with particulate matter (PM). When the ECM judges that a partially clogged condition exists, the ECM begins to perform PM forced regeneration.

When the output voltage of the sensor deviates from the normal operating range, the ECM interprets this as a malfunction of the sensor circuit, and sets DTC P2454 or P2455, and illuminates the MIL.

P2454
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 5 seconds Differential pressure sensor output voltage is below 0.4 V for 3 seconds or more.
(1 trip detection logic)
·

Open or short in differential pressure sensor circuit

·

Incorrect air hose routing

·

Differential pressure sensor

·

ECM



P2455
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 5 seconds Differential pressure sensor output voltage is higher than 4.8 V for 3 seconds or more.
(1 trip detection logic)
·

Open or short in differential pressure sensor circuit

·

Incorrect air hose routing

·

Differential pressure sensor

·

ECM



Related Data List
DTC No. Data List
P2454
P2455
DPF Differential Pressure

HINT:
·

DTC P2453 (Diesel Particulate Filter Pressure Sensor "A" Circuit Range / Performance) will be stored if there is incorrect vacuum hose routing to the differential pressure sensor assembly.

·

After confirming DTC P2454 and P2455, check the differential pressure in the "Powertrain / Engine and ECT / Data List / DPF Differential Pressure" menu using the GTS.


Reference:
Condition DPF Differential Pressure Output Sensor Condition
Engine switch on (IG) Approximately 0 kPa Normal
Always -5 kPa or less or higher than 99 kPa Open or short circuit
4000 rpm (No engine load) Negative output Incorrect hose routing


MONITOR DESCRIPTION

In order to detect abnormality in the differential pressure sensor, the ECM always monitors the output voltage from the sensor. When the sensor output voltage deviates from the normal operating range (between 0.4 V and 4.8 V) for more than 3 seconds, the ECM interprets this as a malfunction in the sensor circuit and illuminates the MIL.

WIRING DIAGRAM

A384892E01
1.479,0.927 1.792,1.125 0.313,0.198 10 false VC 1.396,1.604 1.708,1.802 0.313,0.198 10 false PEX 1.49,2.396 1.802,2.594 0.313,0.198 10 false E2 4.656,0.802 5.229,1.01 0.573,0.208 10 false VCPX 5.656,0.583 5.917,0.771 0.26,0.188 10 false 5V 1.781,1.479 2.094,1.677 0.313,0.198 10 false 2 1.781,2.26 2.094,2.458 0.313,0.198 10 false 1 0.74,2.792 1.115,3 0.375,0.208 10 false C129 0.74,2.969 2.5,3.219 1.76,0.25 10 false Differential Pressure Sensor 1.781,0.802 2.094,1 0.313,0.198 10 false 3 4.375,0.802 4.688,1 0.313,0.198 10 false 32 4.375,1.49 4.688,1.688 0.313,0.198 10 false 27 4.375,2.26 4.688,2.458 0.313,0.198 10 false 26 4.667,1.479 5.24,1.688 0.573,0.208 10 false PEX 4.667,2.26 5.24,2.469 0.573,0.208 10 false EPEX 5.396,3.021 5.969,3.229 0.573,0.208 10 false C151 5.396,3.198 5.969,3.406 0.573,0.208 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF DIFFERENTIAL PRESSURE SENSOR)
a.
U169126E02
1.938,1.281 2.24,1.708 true 1.479,1.281 1.156,1.688 true 0.333,0.25 0.583,0.406 0.25,0.156 10 false *a 2.219,1.729 2.479,1.896 0.26,0.167 10 false VC 0.521,1.083 0.927,1.25 0.406,0.167 10 false C129 0.958,1.688 1.219,1.854 0.26,0.167 10 false E2

Disconnect the differential pressure sensor connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C129-3 (VC) - C129-1 (E2) Engine switch on (IG) 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Differential Pressure Sensor)


d.

Reconnect the differential pressure sensor connector.



OK

2.INSPECT DIFFERENTIAL PRESSURE SENSOR (PEX VOLTAGE)

NG

6.CHECK ECM (POWER SOURCE OF DIFFERENTIAL PRESSURE SENSOR)
2.INSPECT DIFFERENTIAL PRESSURE SENSOR (PEX VOLTAGE)
a.
U169402E02
1.271,1.646 0.958,2.385 true 1.313,1.646 1.698,2.406 true 0.073,0.052 0.344,0.26 0.271,0.208 10 false *a 1.344,0.896 1.76,1.052 0.417,0.156 10 false C151 0.708,2.448 1.635,2.635 0.927,0.188 10 false 27 (PEX) 1.385,2.448 2.167,2.604 0.781,0.156 10 false 26 (EPEX)

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C151-27 (PEX) - C151-26 (EPEX) Engine switch on (IG) 0.4 to 4.8 V


Text in Illustration
*a Component with harness connected
(ECM)



NG

3.CHECK WIRE HARNESS (DIFFERENTIAL PRESSURE SENSOR - ECM)

OK

7.REPLACE ECM
3.CHECK WIRE HARNESS (DIFFERENTIAL PRESSURE SENSOR - ECM)
a.

Disconnect the differential pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C129-2 (PEX) - C151-27 (PEX) Always Below 1 Ω
C129-3 (VC) - C151-32 (VCPX) Always Below 1 Ω
C129-1 (E2) - C151-26 (EPEX) Always Below 1 Ω
C129-2 (PEX) or C151-27 (PEX) - Body ground and other terminals Always 10 kΩ or higher
C129-3 (VC) or C151-32 (VCPX) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the differential pressure sensor connector.


e.

Reconnect the ECM connector.



OK

4.CHECK ECM (CHECK RESISTANCE)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK ECM (CHECK RESISTANCE)
a.
U169127E02
1.969,1.271 2.406,1.688 true 1.51,1.292 1.188,1.698 true 1.698,1.281 1.708,1.75 true 0.333,0.25 0.583,0.406 0.25,0.156 10 false *a 2.406,1.708 2.667,1.875 0.26,0.167 10 false VC 0.521,1.083 0.927,1.25 0.406,0.167 10 false C129 0.979,1.698 1.24,1.865 0.26,0.167 10 false E2 1.552,1.781 1.938,1.948 0.385,0.167 10 false PEX

Disconnect the differential pressure sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C129-3 (VC) - C129-2 (PEX) Engine switch off No short or open circuit
C129-2 (PEX) - C129-1 (E2)


Text in Illustration
*a Front view of wire harness connector
(to Differential Pressure Sensor)


c.

Reconnect the differential pressure sensor connector.



OK

5.REPLACE DIFFERENTIAL PRESSURE SENSOR

NG

7.REPLACE ECM
5.REPLACE DIFFERENTIAL PRESSURE SENSOR
a.


NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CHECK ECM (POWER SOURCE OF DIFFERENTIAL PRESSURE SENSOR)
a.
U169403E02
1.271,1.698 1.125,2.417 true 1.323,1.635 1.875,2.396 true 0.104,0.073 0.375,0.281 0.271,0.208 10 false *a 1.344,0.896 1.76,1.052 0.417,0.156 10 false C151 0.583,2.531 1.469,2.719 0.885,0.188 10 false 32 (VCPX) 1.74,2.552 2.521,2.708 0.781,0.156 10 false 26 (EPEX)

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C151-32 (VCPX) - C151-26 (EPEX) Engine switch on (IG) 4.5 to 5.5 V


Text in Illustration
*a Component with harness connected
(ECM)



OK

8.REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

7.REPLACE ECM
7.REPLACE ECM

NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch on (IG) and wait for 5 seconds.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Confirm that the DTC is not output again.



NEXT

END