The manifold absolute pressure sensor detects the intake manifold pressure. The ECM determines the basic injection volume and injection advance timing based on the voltage output by the manifold absolute pressure sensor.
The manifold absolute pressure sensor monitors the absolute pressure inside the intake manifold (default is 0 kPa [0 mmHg, 0 in.Hg]). As a result, the ECM controls the air-fuel ratio so that it reaches the proper level under any driving conditions.
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| 2 seconds after engine is started, race engine for 1 second | After the engine is started, condition (a) continues for more than 0.5 seconds (1 trip detection logic):
(a) Manifold absolute pressure sensor voltage is 0.1 V or less. |
·
Open or short in manifold absolute pressure sensor circuit ·
Manifold absolute pressure sensor ·
ECM |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| 2 seconds after engine is started, race engine for 1 second | After the engine is started, condition (a) continues for more than 0.5 seconds (1 trip detection logic):
(a) Manifold absolute pressure sensor voltage is 4.8 V or higher. |
·
Open or short in manifold absolute pressure sensor circuit ·
Manifold absolute pressure sensor ·
ECM |
| DTC No. | Data List |
|---|---|
| P0107
P0108 |
·
MAP ·
Atmosphere Pressure |
If DTC P0107 and/or P0108 is stored, the following symptoms may appear:
Misfire
Combustion noise
Black smoke
White smoke
Lack of power
When DTC P0107 or P0108 is stored, check the intake manifold pressure by entering the following menus: Powertrain / Engine and ECT / Data List / MAP.
| GTS Displayed | Malfunction |
|---|---|
| 22 kPa (165 mmHg, 6.5 in.Hg) | ·
Open in VC circuit ·
Open in PIMcircuit ·
Short in PIM circuit |
| 320 kPa (2400 mmHg, 94.5 in.Hg) or higher | ·
Open in E circuit |
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAP.
Read the value.
Same as the actual atmospheric pressure.
Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather (high atmospheric pressure, low atmospheric pressure).
Also, check "Atmosphere Pressure" in the Data List.
NG
OK
Disconnect the manifold absolute pressure sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C83-3 (VC) - C83-1 (E) | Engine switch on (IG) | 4.5 to 5.5 V |
| *a | Front view of wire harness connector
(to Manifold Absolute Pressure Sensor) |
Reconnect the manifold absolute pressure sensor connector.
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C149-18 (PIM) - C149-19 (EPIM) | Engine switch on (IG) | 0.8 to 1.5 V |
| *a | Component with harness connected
(ECM) |
NG
OK
Disconnect the manifold absolute pressure sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C83-2 (PIM) - C149-18 (PIM) | Always | Below 1 Ω |
| C83-1 (E) - C149-19 (EPIM) | Always | Below 1 Ω |
| C83-2 (PIM) or C149-18 (PIM) - Body ground and other terminals | Always | 10 kΩ or higher |
| C83-1 (E) or C149-19 (EPIM) - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the manifold absolute pressure sensor connector.
Reconnect the ECM connector.
OK
NG
Disconnect the manifold absolute pressure sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C83-3 (VC) - C83-2 (PIM) | Engine switch off | No short or open |
| C83-2 (PIM) - C83-1 (E) |
| *a | Front view of wire harness connector
(to Manifold Absolute Pressure Sensor) |
Reconnect the manifold absolute pressure sensor connector.
OK
NG
Replace the manifold absolute pressure sensor (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MANIFOLD ABSOLUTE PRESSURE SENSOR>REMOVAL).
NEXT
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C149-28 (VCPM) - C149-19 (EPIM) | Engine switch on (IG) | 4.5 to 5.5 V |
| *a | Component with harness connected
(ECM) |
OK
NG
Repair or replace the harness or connector.
NEXT
Replace the ECM (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>DTC CHECK / CLEAR).
Turn the engine switch off for 30 seconds or more.
Turn the GTS off.
Turn the engine switch on (IG) for 3 seconds and turn the GTS on.
After the engine is started for 2 seconds, race the engine for 1 second.
Confirm that the DTC is not output again.
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTC P0107 or P0108.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, race the engine for 1 minute, and then idle the engine for 5 minutes.
NEXT