Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2017.08–2018.06
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) U

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  TERMINALS OF ECM  


U169465E03
0.615,0.438 0.979,0.604 0.365,0.167 10 false C149 1.771,0.438 2.135,0.604 0.365,0.167 10 false C150 2.948,0.438 3.313,0.604 0.365,0.167 10 false C151 3.958,0.438 4.323,0.604 0.365,0.167 10 false C152 5.094,0.438 5.458,0.604 0.365,0.167 10 false G184 6.177,0.448 6.542,0.615 0.365,0.167 10 false G185

HINT:

Each ECM terminal's standard voltage is shown in the table below.

In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition".

Use the illustration above as a reference for the ECM terminals.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G185-1 (BATT) - C152-1 (E1) L - W-B Battery (for measuring the battery voltage and for the ECM memory) Always 11 to 14 V
G185-18 (IGSW) - C152-1 (E1) W - W-B Engine switch Engine switch on (IG) 11 to 14 V
G185-2 (+B) - C152-1 (E1) W - W-B Power source of ECM Engine switch on (IG) 11 to 14 V
G185-3 (+B2) - C152-1 (E1) W - W-B Power source of ECM Engine switch on (IG) 11 to 14 V
G185-4 (+B3) - C152-1 (E1) W - W-B Power source of ECM Engine switch on (IG) 11 to 14 V
G184-14 (MREL) - C152-1 (E1) V - W-B EFI MAIN1 relay operation signal Engine switch on (IG) 11 to 14 V
10 seconds elapsed after engine switch off 0 to 1.5 V
C151-5 (+BD1) - C152-1 (E1) B - W-B EDU relay operation signal Engine switch on (IG) 11 to 14 V
C151-4 (+BD2) - C152-1 (E1) B - W-B EDU relay operation signal Engine switch on (IG) 11 to 14 V
G184-15 (GREL) - C152-1 (E1) R - W-B GLOW relay Cranking 11 to 14 V
Idling (10 seconds or more after engine start) 0 to 1.5 V
G185-29 (VCPA) - G185-22 (EPA) LG - P Power source of accelerator pedal position sensor (for VPA) Engine switch on (IG) 4.5 to 5.5 V
G185-30 (VCP2) - G185-25 (EPA2) R - W Power source of accelerator pedal position sensor (for VPA2) Engine switch on (IG) 4.5 to 5.5 V
G185-28 (VPA) - G185-22 (EPA) L - P Accelerator pedal position sensor (for engine control) Engine switch on (IG), accelerator pedal fully released 0.5 to 1.1 V
Engine switch on (IG), accelerator pedal fully depressed 3.0 to 4.6 V
G185-31 (VPA2) - G185-25 (EPA2) GR - W Accelerator pedal position sensor (for sensor malfunction detection) Engine switch on (IG), accelerator pedal fully released 0.9 to 2.3 V
Engine switch on (IG), accelerator pedal fully depressed 3.4 to 5.0 V
C150-25 (VCVG) - C150-24 (EVG) R - G Power source of mass air flow meter sub-assembly (for VG) Engine switch on (IG) 4.8 to 5.2 V
C150-33 (VG) - C150-24 (EVG) W - G Mass air flow meter sub-assembly signal Engine switch on (IG) Pulse generation
(See waveform 1)
C150-32 (THA) - C150-24 (EVG) Y-B - G Intake air temperature sensor (built into mass air flow meter sub-assembly) Idling, intake air temperature at 20°C (68°F) 0.5 to 3.4 V
C150-35 (THIA) - C150-27 (ETHI) B - BR Intake air temperature sensor (turbo) Idling, intake air temperature at 0 to 80°C (32 to 176°F) 0.5 to 3.4 V
C149-34 (THW) - C149-27 (ETHW) R-L - BR Engine coolant temperature sensor Idling, engine coolant temperature at 80°C (176°F) 0.2 to 1.0 V
G184-22 (STA) - C152-1 (E1) W - W-B Starter signal Cranking 6.0 V or higher
C149-6 (#1D+) - C149-7 (#1D-) W - B No. 1 injector assembly signal Idling Pulse generation
(See waveform 2)
C149-1 (#2D+) - C149-2 (#2D-) V - P No. 2 injector assembly signal
C150-7 (#3D+) - C150-6 (#3D-) L - LG No. 3 injector assembly signal
C149-5 (#4D+) - C149-4 (#4D-) G - L No. 4 injector assembly signal
C152-17 (VCG) - C152-18 (G2-) B - L Power source of camshaft position sensor (specific voltage) Engine switch on (IG) 4.5 to 5.5 V
C152-27 (G2+) - C152-18 (G2-) GR - L Camshaft position sensor Idling Pulse generation
(See waveform 3)
C152-20 (VCNE) - C152-19 (NE-) R - L Power source of crankshaft position sensor (specific voltage) Engine switch on (IG) 4.5 to 5.5 V
C152-28 (NE+) - C152-19 (NE-) W - L Crankshaft position sensor Idling Pulse generation
(See waveform 4)
G185-13 (STP) - C152-1 (E1) V - W-B Stop light switch assembly Engine switch on (IG), brake pedal depressed 7.5 to 14 V
Engine switch on (IG), brake pedal released 0 to 1.5 V
G185-12 (ST1-) - C152-1 (E1) B - W-B Stop light switch assembly
(opposite to STP)
Engine switch on (IG), brake pedal depressed 0 to 1.5 V
Engine switch on (IG), brake pedal released 7.5 to 14 V
G184-25 (TC) - C152-1 (E1) V - W-B Terminal TC of DLC3 Engine switch on (IG) 11 to 14 V
G184-10 (SPD) - C152-1 (E1) R - W-B Speed signal from combination meter assembly Engine switch on (IG), slowly wheel rotated Pulse generation
(See waveform 5)
C149-28 (VCPM) - C149-19 (EPIM) R - B Power source of manifold absolute pressure sensor
(specific voltage)
Engine switch on (IG) 4.5 to 5.5 V
C149-18 (PIM) - C149-19 (EPIM) L-B - B Manifold absolute pressure sensor Negative pressure of 40 kPa (300 mmHg, 11.8 in.Hg) applied 0.1 to 0.7 V
Same as atmospheric pressure 0.8 to 1.5 V
Positive pressure of 170 kPa (1275 mmHg, 50.2 in.Hg) applied 1.6 to 2.3 V
G184-16 (TACH) - C152-1 (E1) P - W-B Engine speed Idling Pulse generation
(See waveform 6)
C151-28 (VCM) - C151-19 (E2M) Y-B - GR Power source of fuel pressure sensor (for PCR1) Engine switch on (IG) 4.5 to 5.5 V
C151-18 (PCR1) - C151-19 (E2M) R - GR Fuel pressure sensor (main) Idling 1.8 to 2.1 V
C152-33 (VCS) - C152-25 (E2S) LG - L Power source of fuel pressure sensor (for PCR2) Engine switch on (IG) 4.5 to 5.5 V
C152-26 (PCR2) - C152-25 (E2S) Y - L Fuel pressure sensor (sub) Idling 1.2 to 1.5 V
C150-3 (PCV+) - C150-4 (PCV-) W - B Pre-stroke control valve operation signal Idling Pulse generation
(See waveform 7)
C150-2 (PRV+) - C150-1 (PRV-) Y - G Pressure discharge valve signal Engine switch turned off after idling Pulse generation
C151-1 (VNM+) - C152-1 (E1) W - W-B DC motor signal
(turbocharger nozzle vane control actuator)
Idling Pulse generation
C151-2 (VNM-) - C152-1 (E1) B - W-B DC motor signal
(turbocharger nozzle vane control actuator)
Idling Pulse generation
C151-30 (VNVC) - C151-22 (VNE2) W - L Power source of nozzle vane position sensor
(turbocharger nozzle vane control actuator)
Engine switch on (IG) 4.5 to 5.5 V
C151-23 (VNA) - C151-22 (VNE2) R - L Nozzle vane position sensor signal
(turbocharger nozzle vane control actuator)
Engine switch on (IG) 2.3 to 2.7 V
C151-29 (VCVL) - C151-20 (EVLU) LG - W Power source of throttle position sensor Engine switch on (IG) 4.5 to 5.5 V
C151-21 (VLU) - C151-20 (EVLU) R - W Throttle position sensor signal Engine switch on (IG), throttle valve fully opened 3.6 to 4.2 V
Engine switch on (IG), throttle valve fully closed 0.4 to 1.0 V
C152-6 (M+) - C152-3 (ME01) R - W-B Diesel throttle duty signal Engine warmed up, racing engine Pulse generation
C152-5 (M-) - C152-3 (ME01) L - W-B Diesel throttle duty signal Engine warmed up, racing engine Pulse generation
C151-31 (VCEG) - C151-24 (EEGL) V - G Power source of EGR valve position sensor Engine switch on (IG) 4.5 to 5.5 V
C151-25 (EGLS) - C151-24 (EEGL) R-Y - G EGR valve position sensor Engine switch on (IG) 0.6 to 1.4 V
C151-6 (EGM+) - C152-1 (E1) LG- W-B EGR valve duty signal Engine warmed up, idling Pulse generation
C151-7 (EGM-) - C152-1 (E1) V - W-B EGR valve duty signal Engine warmed up, idling Pulse generation
C149-16 (ECBV) - C152-1 (E1) L-Y - W-B No. 1 vacuum switching valve assembly (for EGR bypass valve) No. 1 vacuum switching valve assembly (for EGR bypass valve) on 0 to 1.5 V
No. 1 vacuum switching valve assembly (for EGR bypass valve) off 11 to 14 V
C151-32 (VCPX) - C151-26 (EPEX) L - G Power source of differential pressure sensor Engine switch on (IG) 4.5 to 5.5 V
C151-27 (PEX) - C151-26 (EPEX) L - G Differential pressure sensor Engine switch on (IG) 0.4 to 4.8 V
G184-5 (HA1A) - C152-2 (E04) W - W-B Air fuel ratio sensor heater Engine switch on (IG) 11 to 14 V
Idling before air fuel ratio sensor warmed Pulse generation
(See waveform 8)
C152-31 (A1A+) - C152-1 (E1) P - W-B Air fuel ratio sensor Engine switch on (IG) 2.0 to 2.5 V
C152-32 (A1A-) - C152-1 (E1) L - W-B Air fuel ratio sensor Engine switch on (IG) 2.0 to 2.5 V
G184-6 (FIV) - C152-1 (E1) W - W-B Exhaust fuel addition injector Exhaust fuel addition injector operating Pulse generation
C149-23 (THTO) - C149-22 (ETTO) R-W - G-B Exhaust gas temperature sensor Engine warmed up, idling 0.2 to 4.95 V
C149-25 (THCI) - C149-24 (ETCI) G-B - G-R No. 2 Exhaust gas temperature sensor Engine warmed up, idling 0.2 to 4.95 V
C149-33 (THCO) - C149-26 (ETCO) B - R No. 3 Exhaust gas temperature sensor Engine warmed up, idling 0.2 to 4.95 V
G184-26 (THSO) - G184-33 (ETSO) P - W No. 4 Exhaust gas temperature sensor Engine warmed up, idling 0.2 to 4.95 V
C149-10 (SCV) - C151-3 (E01) G - W-B Vacuum switching valve assembly (for swirl control valve) Idling 0 to 1.5 V
Engine speed 2600 rpm or more 11 to 14 V
C150-12 (ACM) - C151-3 (E01) LG-B - W-B Vacuum switching valve sub-assembly (for engine mounting) Idling 0 to 1.5 V
Engine speed 2600 rpm or more 11 to 14 V
G184-11 (NSW)*1 - C152-1 (E1) B - W-B Park/neutral position switch assembly Engine switch on (IG), shift lever in P or N Below 3 V
Engine switch on (IG), shift lever not in P and N 11 to 14 V
G184-28 (CANL) - C152-1 (E1) W - W-B CAN communication line Engine switch on (IG) Pulse generation
(See waveform 9)
G184-17 (CANH) - C152-1 (E1) R*2 - W-B
LG*3 - W-B
CAN communication line Engine switch on (IG) Pulse generation
(See waveform 10)
G184-27 (CANU) - C152-1 (E1) L - W-B CAN communication line Engine switch on (IG) Pulse generation
(See waveform 10)
G184-35 (CAND) - C152-1 (E1) W - W-B CAN communication line Engine switch on (IG) Pulse generation
(See waveform 9)
C152-7 (LIN) - C152-1 (E1) L - W-B LIN communication line Engine switch on (IG) Pulse generation
(See waveform 11)
C151-3 (E01) - Body ground W-B - Body ground Earth (ground) circuit of ECM Always Below 1 Ω
C152-4 (E02) - Body ground W-B - Body ground Earth (ground) circuit of ECM Always Below 1 Ω
C152-1 (E1) - Body ground W-B - Body ground Earth (ground) circuit of ECM Always Below 1 Ω
C152-3 (ME01) - Body ground W-B - Body ground Earth (ground) circuit of ECM Always Below 1 Ω
G185-8 (EC) - Body ground W-B - Body ground Earth (ground) circuit of ECM Always Below 1 Ω
C149-3 (E1D1) - Body ground W-B - Body ground Earth (ground) circuit of ECM Always Below 1 Ω
C150-5 (E1D2) - Body ground W-B - Body ground Earth (ground) circuit of ECM Always Below 1 Ω
C152-2 (E04) - Body ground W-B - Body ground Earth (ground) circuit of ECM Always Below 1 Ω

HINT:
·

*1: for Automatic Transmission

·

*2: for LHD

·

*3: for RHD



WAVEFORM 1


A337204E02
0.167,1.458 0.625,1.656 0.458,0.198 10 false GND

Mass Air Flow Meter Sub-assembly Signal
Item Content
ECM Terminal Name Between VG and EVG
Tester Range 1 V/DIV., 100 μsec./DIV.
Condition Engine switch on (IG)


WAVEFORM 2


A346498E01
1.094,1.917 1.958,2.115 0.865,0.198 10 false 1 msec./DIV. 2.781,0.146 3.396,0.344 0.615,0.198 10 false 10 V/DIV. 2.969,1.188 3.344,1.385 0.375,0.198 10 false GND

No. 1 (to No. 4) Injector Assembly Signal
Item Content
ECM Terminal Name Between #1D+ and #1D-
Between #2D+ and #2D-
Between #3D+ and #3D-
Between #4D+ and #4D-
Tester Range 10 V/DIV., 1 msec./DIV.
Condition Idling after engine warmed

HINT:

The waveform varies depending on the injector injection.



WAVEFORM 3


A340470E01
2.854,0.156 3.406,0.344 0.552,0.188 10 false 5 V/DIV. 3.042,1.427 3.406,1.646 0.365,0.219 10 false GND 1.094,1.854 2.052,2.031 0.958,0.177 10 false 20 msec./DIV.

Camshaft Position Sensor Signal
Item Content
ECM Terminal Name Between G2+ and G2-
Tester Range 2 V/DIV., 20 msec./DIV.
Condition Idling after engine warmed

HINT:

The waveform varies depending on the engine speed.



WAVEFORM 4


A362183E01
0.732,1.671 1.694,1.879 0.961,0.208 10 10 msec./DIV. 2.597,0 3.190,0.208 0.593,0.208 10 2 V/DIV. 3.022,1.276 3.362,1.439 0.340,0.163 10 GND

Crankshaft Position Sensor Signal
Item Content
ECM Terminal Name Between NE+ and NE-
Tester Range 2 V/DIV., 10 msec./DIV.
Condition Idling after engine warmed

HINT:

The wavelength becomes shorter as the engine speed.



WAVEFORM 5


U169139E01
2.878,1.177 2.808,1.177 false 2.766,0.111 3.317,0.273 0.551,0.163 10 5 V/DIV. 2.919,1.094 3.290,1.257 0.371,0.163 10 GND 0.136,1.073 0.459,1.236 0.323,0.163 10 SPD 1.503,1.842 2.460,2.005 0.957,0.163 10 10 msec./DIV.

Vehicle Speed Signal
Item Content
ECM Terminal Name Between SPD and E1
Tool Setting 5 V/DIV., 10 msec./DIV.
Condition Driving at vehicle speed of 40 km/h (25 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



WAVEFORM 6


A292385E01
0.542,1.167 1,1.365 0.458,0.198 10 GND 0.125,0.125 0.948,0.354 0.823,0.229 10 5 V/DIV. 1.75,1.917 2.563,2.104 0.813,0.188 10 10 ms./DIV.

Engine Speed Signal
Item Content
ECM Terminal Name Between TACH and E1
Tester Range 5 V/DIV., 10 msec./DIV.
Condition Idling after engine warmed

HINT:

The waveform varies depending on the engine speed.



WAVEFORM 7


A346499E01
2.76,0.073 3.385,0.292 0.625,0.219 10 false 10 V/DIV. 1.104,1.865 2.083,2.042 0.979,0.177 10 false 20 msec./DIV. 3.031,1.01 3.365,1.208 0.333,0.198 10 false GND

Pre-stroke Control Valve Signal
Item Content
ECM Terminal Name Between PCV+ and PCV-
Tester Range 10 V/DIV., 20 msec./DIV.
Condition Idling after engine warmed

HINT:

The waveform varies depending on pre-stroke control valve operation.



WAVEFORM 8


A287796E06
2.594,1.656 3.052,1.854 0.458,0.198 10 GND 0.063,0.063 0.781,0.292 0.719,0.229 10 1 V/DIV. 1.167,1.927 2,2.135 0.833,0.208 10 2 ms./DIV.

Engine Speed Signal
Item Content
ECM Terminal Name Between NEO and E1
Tester Range 1 V/DIV., 2 msec./DIV.
Condition Racing with warm engine


WAVEFORM 9


U169141E01
2.911,1.287 2.84,1.287 false 2.771,0.121 3.318,0.284 0.547,0.163 10 1 V/DIV. 2.972,1.2 3.344,1.363 0.371,0.163 10 GND 1.594,1.7 2.878,1.863 1.283,0.163 10 10 msec./DIV.

CAN Communication Signal
Item Content
ECM Terminal Name Between CANL and E1
Between CAND and E1
Tester Range 1 V/DIV., 10 msec./DIV.
Condition Engine stopped, Engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 10


U169140E01
2.884,1.307 2.813,1.307 false 2.744,0.142 3.291,0.304 0.547,0.163 10 1 V/DIV. 2.945,1.221 3.317,1.383 0.371,0.163 10 GND 1.567,1.73 2.828,1.893 1.260,0.163 10 10 msec./DIV.

CAN Communication Signal
Item Content
ECM Terminal Name Between CANH and E1
Between CANU and E1
Tester Range 1 V/DIV., 10 msec./DIV.
Condition Engine stopped, Engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 11


A349005E01
1.177,2.49 2.188,2.688 1.01,0.198 10 false 10 msec./DIV. 2.917,1.896 3.271,2.104 0.354,0.208 10 false GND 2.698,0.792 3.292,0.99 0.594,0.198 10 false 2 V/DIV.

LIN Communication Signal
Item Content
ECM Terminal Name Between LIN and E1
Tester Range 2 V/DIV., 10 msec./DIV.
Condition Engine stopped, Engine switch on (IG)