Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2017.08
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P2610  ECM / PCM Internal Engine Off Timer Performance  


DESCRIPTION

The soak timer operates after the engine switch is turned off. When a certain amount of time has elapsed after turning the engine switch off, the soak timer activates the ECM to perform malfunction checks which can only be performed after the engine is stopped. The soak timer is built into the ECM.

A290317E22
4.167,0.833 4.583,1 0.417,0.167 10 false IGSW 4.333,2.667 4.583,2.833 0.25,0.167 10 false +B 4.167,3.469 4.583,3.635 0.417,0.167 10 false MREL 5,1.25 5.75,1.583 0.75,0.333 10 false Soak Timer IC 5,2.583 5.667,2.917 0.667,0.333 10 false Power Source IC 5,3.417 5.833,3.75 0.833,0.333 10 false MAIN Relay Control IC 5.5,4.333 5.917,4.5 0.417,0.167 10 false ECM 3.729,1.156 4.5,1.385 0.771,0.229 10 false IGN NO. 2 2.938,1.74 3.24,1.938 0.302,0.198 10 false IG2 2.604,3.906 3.688,4.073 1.083,0.167 10 false EFI MAIN NO. 1 1.99,1.135 2.729,1.385 0.74,0.25 10 false IG2 1.583,2.125 3.135,2.542 1.552,0.417 10 false Certification ECU (Smart Key ECU Assembly) 0.583,3.167 1.417,3.333 0.833,0.167 10 false from Battery 1.74,3.344 2.823,3.51 1.083,0.167 10 false EFI MAIN NO. 1 0.583,0.979 1.417,1.146 0.833,0.167 10 false from Battery

DTC No. DTC Detection Condition Trouble Area
P2610 ECM internal malfunction (2 trip detection logic). ECM

MONITOR DESCRIPTION

1.

While the engine is running, the ECM monitors the synchronization of the soak timer and the CPU clock. If these two are not synchronized, the ECM interprets this as a malfunction, illuminates the MIL and stores the DTC.

2.

If the soak timer activates the ECM even though only a short amount of time has elapsed since the engine switch was turned off, or if the soak timer does not activate the ECM even though a considerable amount of time has elapsed since the engine switch was turned off, the ECM determines that the soak timer is malfunctioning, illuminates the MIL and stores a DTC the next time the engine switch is turned to on (IG).


CAUTION / NOTICE / HINT

HINT:
·

DTC P2610 is stored if an internal ECM problem is detected. Diagnostic procedures are not required. ECM replacement is necessary.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.REPLACE ECM

NEXT

2.CHECK WHETHER DTC OUTPUT RECURS
2.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Start the engine and wait for 10 minutes or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


g.

If no pending DTC is output, the repair has been successfully completed.



NEXT

END