Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2017.08
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P2118  Throttle Actuator Control Motor Current Range / Performance  


DESCRIPTION

The ETCS (Electronic Throttle Control System) has a dedicated power supply circuit. The voltage (+BM) is monitored and when it is low (below 4 V), the ECM determines that there is a malfunction in the ETCS and cuts off the current to the throttle actuator.

When the voltage becomes unstable, the ETCS itself becomes unstable. For this reason, when the voltage is low, the current to the throttle actuator is cut. If repairs are made and the system returns to normal, turn the engine switch off. The ECM then allows the current to flow to the throttle actuator so that it can be restarted.

HINT:

The ETCS does not use a throttle cable.


A374780E09
0.083,0.948 0.865,1.51 0.781,0.563 10 false from EFI MAIN NO. 1 Relay 0.208,1.719 0.729,2.115 0.521,0.396 10 false from Battery 1.198,1.99 1.677,2.188 0.479,0.198 10 false ETCS 0.813,3.531 1.948,3.719 1.135,0.188 10 false Throttle Actuator 4.729,3.75 5.198,3.927 0.469,0.177 10 false ME01 4.729,3.073 5.01,3.26 0.281,0.188 10 false M- 4.719,2.417 5,2.604 0.281,0.188 10 false M+ 4.719,1.677 5.115,1.865 0.396,0.188 10 false +BM 4.729,0.917 5.125,1.104 0.396,0.188 10 false +B 5.438,1.521 6.781,1.875 1.344,0.354 10 false Power Source Circuit for CPU 5.521,3.396 6.604,3.74 1.083,0.344 10 false Throttle Actuator Control Circuit 5.656,4.229 6.115,4.427 0.458,0.198 10 false ECM

DTC No. DTC Detection Condition Trouble Area
P2118 An open in the ETCS power source (+BM) circuit (1 trip detection logic).
·

Open in ETCS power source circuit

·

Battery

·

Battery terminals

·

ETCS fuse

·

ECM



MONITOR DESCRIPTION

The ECM monitors the battery supply voltage applied to the throttle actuator.

When the power supply voltage (+BM) drops below 4 V for 0.8 seconds or more, the ECM interprets this as an open in the power supply circuit (+BM). The ECM illuminates the MIL and stores the DTC.

If the malfunction is not repaired successfully, the DTC is stored 5 seconds after the engine is next started.

FAIL-SAFE

When this DTC or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 7° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal opening angle to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

Fail-safe mode continues until a pass condition is detected, and the engine switch is then turned off.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (+BM VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / +BM Voltage.


e.

Read the value displayed on the GTS.

Standard Voltage:

11 to 14 V




OK

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY, BODY GROUND)

NG

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY, BODY GROUND)
a.

Disconnect the ECM connector.


U169512E01
1.938,2.115 2.375,1.896 false 1.938,2.417 2.375,2.708 false 0.802,2.125 1.104,2.292 0.302,0.167 10 false C36 2.417,1.792 3.115,1.969 0.698,0.177 10 false 6 (+BM)*A 2.427,2.635 3.208,2.813 0.781,0.177 10 false 23 (+BM)*B 0.031,0 0.271,0.198 0.24,0.198 10 false *a

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for Automatic Transmission
Tester Connection Condition Specified Condition
C36-6 (+BM) - Body ground Always 11 to 14 V

for Manual Transmission
Tester Connection Condition Specified Condition
C36-23 (+BM) - Body ground Always 11 to 14 V


Text in Illustration
*A for Automatic Transmission
*B for Manual Transmission
*a Rear view of wire harness connector
(to ECM)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Automatic Transmission
Tester Connection Condition Specified Condition
C36-29 (ME01) - Body ground Always Below 1 Ω
C36-12 (E1) - Body ground Always Below 1 Ω

for Manual Transmission
Tester Connection Condition Specified Condition
C37-10 (ME01) - Body ground Always Below 1 Ω
C36-12 (E1) - Body ground Always Below 1 Ω



d.

Reconnect the ECM connector.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG