Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2017.08
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM J

1GR-FE ENGINE CONTROL  SFI SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the engine switch is turned on (IG), battery voltage is applied to the IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes a current to flow to the coil, closing the contacts of the No. 1 integration relay (EFI MAIN NO. 1 relay) and supplying power to terminals +B and +B2 of the ECM.

WIRING DIAGRAM

for Automatic Transmission
A411066E03
6.135,2.01 6.75,2.208 0.615,0.198 10 false IGSW 5.75,2.125 6.365,2.323 0.615,0.198 10 false G55 5.854,1.917 6.073,2.115 0.219,0.198 10 false 21 6.167,2.969 6.479,3.167 0.313,0.198 10 false +B 6.167,3.354 6.625,3.552 0.458,0.198 10 false +B2 5.74,3 6.354,3.198 0.615,0.198 10 false G55 5.74,3.365 6.354,3.563 0.615,0.198 10 false G55 5.844,2.771 6.063,2.958 0.219,0.188 10 false 23 5.865,3.198 6.063,3.406 0.198,0.208 10 false 22 6.135,3.698 6.75,3.896 0.615,0.198 10 false MREL 5.74,3.802 6.354,4 0.615,0.198 10 false G56 5.844,3.604 6.156,3.802 0.313,0.198 10 false 36 5.75,4.521 6.208,4.719 0.458,0.198 10 false C36 5.833,4.302 6.052,4.5 0.219,0.198 10 false 12 6.156,4.51 6.469,4.708 0.313,0.198 10 false E1 4.042,0.365 4.198,0.563 0.156,0.198 10 false 3 3.604,0.458 4.219,0.656 0.615,0.198 10 false IG1D 2.531,0.917 3.146,1.115 0.615,0.198 10 false G213 2.531,1.094 4.354,1.51 1.823,0.417 10 false Certification ECU (Smart Key ECU Assembly) 4.073,2.125 4.385,2.323 0.313,0.198 10 false 1V 4.167,1.927 4.323,2.125 0.156,0.198 10 false 1 4.073,2.51 4.385,2.708 0.313,0.198 10 false 1V 4.167,2.323 4.323,2.521 0.156,0.198 10 false 2 3.271,2.76 3.729,2.958 0.458,0.198 10 false IG2 2.625,2.281 3.083,2.479 0.458,0.198 10 false IG2 1.406,2.125 1.719,2.323 0.313,0.198 10 false 1S 1.5,1.917 1.656,2.115 0.156,0.198 10 false 1 1.385,3.813 1.698,4.01 0.313,0.198 10 false 1W 1.49,3.583 1.646,3.781 0.156,0.198 10 false 4 4.052,3.375 4.365,3.573 0.313,0.198 10 false 1W 4.135,3.167 4.448,3.365 0.313,0.198 10 false 10 4.042,3.802 4.354,4 0.313,0.198 10 false 1W 4.156,3.604 4.313,3.802 0.156,0.198 10 false 8 2.979,4 5.125,4.198 2.146,0.198 10 false EFI MAIN NO. 1 2.042,3.5 3.125,3.729 1.083,0.229 10 false EFI MAIN NO. 1 2.917,4.625 4.427,4.875 1.51,0.25 10 false No. 1 Integration Relay 0.604,2.281 1.146,2.479 0.542,0.198 10 false 70A FL 4.885,2.292 5.594,2.49 0.708,0.198 10 false IGN NO. 2 6.385,5.094 6.844,5.292 0.458,0.198 10 false ECM 0.563,4.573 1.635,4.771 1.073,0.198 10 false Battery


for Manual Transmission
A411066E04
6.135,2.01 6.75,2.208 0.615,0.198 10 false IGSW 5.729,2.125 6.344,2.323 0.615,0.198 10 false G56 5.854,1.917 6.073,2.115 0.219,0.198 10 false 21 6.167,2.969 6.479,3.167 0.313,0.198 10 false +B 6.167,3.354 6.625,3.552 0.458,0.198 10 false +B2 5.74,3 6.354,3.198 0.615,0.198 10 false G55 5.74,3.365 6.354,3.563 0.615,0.198 10 false G55 5.844,2.771 6.063,2.958 0.219,0.188 10 false 22 5.865,3.198 6.063,3.406 0.198,0.208 10 false 23 6.135,3.698 6.75,3.896 0.615,0.198 10 false MREL 5.74,3.802 6.354,4 0.615,0.198 10 false G55 5.844,3.604 6.156,3.802 0.313,0.198 10 false 9 5.75,4.521 6.208,4.719 0.458,0.198 10 false C36 5.833,4.302 6.052,4.5 0.219,0.198 10 false 12 6.156,4.51 6.469,4.708 0.313,0.198 10 false E1 4.042,0.365 4.198,0.563 0.156,0.198 10 false 3 3.604,0.458 4.219,0.656 0.615,0.198 10 false IG1D 2.531,0.917 3.146,1.115 0.615,0.198 10 false G213 2.531,1.094 4.354,1.51 1.823,0.417 10 false Certification ECU (Smart Key ECU Assembly) 4.073,2.125 4.385,2.323 0.313,0.198 10 false 1V 4.167,1.927 4.323,2.125 0.156,0.198 10 false 1 4.073,2.51 4.385,2.708 0.313,0.198 10 false 1V 4.167,2.323 4.323,2.521 0.156,0.198 10 false 2 3.271,2.76 3.729,2.958 0.458,0.198 10 false IG2 2.625,2.281 3.083,2.479 0.458,0.198 10 false IG2 1.406,2.125 1.719,2.323 0.313,0.198 10 false 1S 1.5,1.917 1.656,2.115 0.156,0.198 10 false 1 1.385,3.813 1.698,4.01 0.313,0.198 10 false 1W 1.49,3.583 1.646,3.781 0.156,0.198 10 false 4 4.052,3.375 4.365,3.573 0.313,0.198 10 false 1W 4.135,3.167 4.448,3.365 0.313,0.198 10 false 10 4.042,3.802 4.354,4 0.313,0.198 10 false 1W 4.156,3.604 4.313,3.802 0.156,0.198 10 false 8 2.979,4 5.125,4.198 2.146,0.198 10 false EFI MAIN NO. 1 2.042,3.5 3.125,3.729 1.083,0.229 10 false EFI MAIN NO. 1 2.917,4.625 4.427,4.875 1.51,0.25 10 false No. 1 Integration Relay 0.542,2.281 1.146,2.49 0.604,0.208 10 false 70A FL 4.885,2.292 5.594,2.49 0.708,0.198 10 false IGN NO. 2 6.385,5.094 6.844,5.292 0.458,0.198 10 false ECM 0.563,4.573 1.635,4.771 1.073,0.198 10 false Battery


CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BATTERY)
U147511E04
0.26,0.135 0.479,0.323 0.219,0.188 10 false *a 0.677,1.104 0.99,1.292 0.313,0.188 10 false 1S

a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1S-1 - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to No. 1 Integration Relay)



OK

2.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN NO. 1 RELAY AND IG2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN NO. 1 RELAY AND IG2 RELAY)
a.

Inspect the No. 1 integration relay (EFI MAIN NO. 1 relay) (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).


b.

Inspect the No. 1 integration relay (IG2 relay) (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)

NG

REPLACE NO. 1 INTEGRATION RELAY

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for Automatic Transmission
Tester Connection Condition Specified Condition
G56-36 (MREL) - 1W-8 Always Below 1 Ω
G55-23 (+B) - 1W-10 Always Below 1 Ω
G55-22 (+B2) - 1W-10 Always Below 1 Ω

for Manual Transmission
Tester Connection Condition Specified Condition
G55-9 (MREL) - 1W-8 Always Below 1 Ω
G55-22 (+B) - 1W-10 Always Below 1 Ω
G55-23 (+B2) - 1W-10 Always Below 1 Ω


Standard Resistance (Check for Short):
for Automatic Transmission
Tester Connection Condition Specified Condition
G56-36 (MREL) or 1W-8 - Body ground and other terminals Always 10 kΩ or higher
G55-23 (+B) or 1W-10 - Body ground and other terminals Always 10 kΩ or higher
G55-22 (+B2) or 1W-10 - Body ground and other terminals Always 10 kΩ or higher

for Manual Transmission
Tester Connection Condition Specified Condition
G55-9 (MREL) or 1W-8 - Body ground and other terminals Always 10 kΩ or higher
G55-22 (+B) or 1W-10 - Body ground and other terminals Always 10 kΩ or higher
G55-23 (+B2) or 1W-10 - Body ground and other terminals Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1W-4 - Body ground Always Below 1 Ω




OK

5.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C36-12 (E1) - Body ground Always Below 1 Ω




OK

6.INSPECT ECM (IGSW VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT ECM (IGSW VOLTAGE)
U169407E02
2.375,1.75 2.698,2.74 false 0.802,1.927 0.448,2.76 false 1.094,1.833 1.25,2.406 false 0.521,1.167 0.823,1.333 0.302,0.167 10 false G55 0.979,1.156 1.281,1.323 0.302,0.167 10 false G56 2.104,1.167 2.406,1.333 0.302,0.167 10 false C36 0.073,0.01 0.292,0.219 0.219,0.208 10 false *a 0.344,2.802 1.219,2.979 0.875,0.177 10 false 21 (IGSW)*A 1.188,2.427 2.063,2.604 0.875,0.177 10 false 21 (IGSW)*B 2.635,2.76 3.135,2.938 0.5,0.177 10 false 12 (E1)

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for Automatic Transmission
Tester Connection Switch Condition Specified Condition
G55-21 (IGSW) - C36-12 (E1) Engine switch on (IG) 11 to 14 V

for Manual Transmission
Tester Connection Switch Condition Specified Condition
G56-21 (IGSW) - C36-12 (E1) Engine switch on (IG) 11 to 14 V


Text in Illustration
*A for Automatic Transmission
*B for Manual Transmission
*a Component with harness connected
(ECM)



OK

NG

7.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
7.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for Automatic Transmission
Tester Connection Condition Specified Condition
1V-1 - G55-21 (IGSW) Always Below 1 Ω

for Manual Transmission
Tester Connection Condition Specified Condition
1V-1 - G56-21 (IGSW) Always Below 1 Ω


Standard Resistance (Check for Short):
for Automatic Transmission
Tester Connection Condition Specified Condition
1V-1 or G52-21 (IGSW) - Body ground and other terminals Always 10 kΩ or higher

for Manual Transmission
Tester Connection Condition Specified Condition
1V-1 or G56-21 (IGSW) - Body ground and other terminals Always 10 kΩ or higher




OK

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INTEGRATION RELAY)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
G213-3 (IG1D) - 1V-2 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
G213-3 (IG1D) or 1V-2 - Body ground and other terminals Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR