Home › Engine / Hybrid System › CRUISE CONTROL › FORWARD RECOGNITION CAMERA SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053696 CRUISE CONTROL _0332059 FORWARD RECOGNITION CAMERA SYSTEM U

CRUISE CONTROL  FORWARD RECOGNITION CAMERA SYSTEM  TERMINALS OF ECU  


CHECK FORWARD RECOGNITION CAMERA


E256359E98
2.083,0.75 2.5,1 0.417,0.25 2.156,0.802 2.615,1 0.458,0.198 10 false W22

a.

Disconnect the W22 forward recognition camera connector.

NOTICE:
·

DTCs may be output when connectors are disconnected during inspection. Therefore, be sure to clear the DTCs using the GTS once the inspection has been completed.

·

Do not apply excessive force to the W22 forward recognition camera connector.




b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

If the result is not as specified, there may be a malfunction on the wire harness side.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
W22-7 (IGB) - Body ground G - Body ground Power source Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
W22-10 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the W22 forward recognition camera connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
W22-1 (HTR) - Body ground P - Body ground Forward recognition with heater hood sub-assembly operation signal Ignition switch ON,
Forward recognition with heater hood sub-assembly not operating
11 to 14 V
Ignition switch ON,
Forward recognition with heater hood sub-assembly operating
Below 1 V


e.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
W22-5 (CA1P) - W22-10 (GND) GR - W-B CAN communication signal Ignition switch ON Pulse generation
(See waveform 1)
W22-11 (CA1N) - W22-10 (GND) W - W-B CAN communication signal Ignition switch ON Pulse generation
(See waveform 2)
W22-6 (CANH) - W22-10 (GND) G - W-B CAN communication signal Ignition switch ON Pulse generation
(See waveform 1)
W22-12 (CANL) - W22-10 (GND) W - W-B CAN communication signal Ignition switch ON Pulse generation
(See waveform 2)


f.

WAVEFORM 1

i.
A086154E97
2.75,0.271 3.365,0.521 0.615,0.25 10 false 1 V/DIV. 1.365,1.906 2.313,2.094 0.948,0.188 10 false 10 μsec./DIV.

CAN communication signal

Item Content
Terminal Name Between W22-5 (CA1P) and W22-10 (GND)
Between W22-6 (CANH) and W22-10 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.




g.

WAVEFORM 2

i.
A086155E89
2.76,0.281 3.396,0.51 0.635,0.229 10 false 1 V/DIV. 1.365,1.875 2.333,2.073 0.969,0.198 10 false 10 μsec./DIV.

CAN communication signal

Item Content
Terminal Name Between W22-11 (CA1N) and W22-10 (GND)
Between W22-12 (CANL) and W22-10 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.