RM27T0E
_V1
General
_053654
SPECIFICATIONS
_0260351
1GR-FE ENGINE CONTROL
F
SPECIFICATIONS 1GR-FE ENGINE CONTROL SERVICE DATA
- Camshaft Timing Oil Control Valve:
| Tester Connection
|
Condition
|
Specified Condition
|
| 1 - 2
|
20°C (68°F)
|
6.9 to 7.9 Ω
|
- Crankshaft Position Sensor:
| Tester Connection
|
Condition
|
Specified Condition
|
| 1 - 2
|
Cold
|
1630 to 2740 Ω
|
| Hot
|
2065 to 3225 Ω
|
- Engine Coolant Temperature Sensor:
| Tester Connection
|
Condition
|
Specified Condition
|
| 1 - 2
|
Approx. 20°C (68°F)
|
2.32 to 2.59 kΩ
|
| Approx. 80°C (176°F)
|
0.310 to 0.326 kΩ
|
- Throttle Body:
| Tester Connection
|
Condition
|
Specified Condition
|
| 2 (M+) - 1 (M-)
|
20°C (68°F)
|
0.3 to 100 Ω
|
- Knock Sensor:
| Tester Connection
|
Condition
|
Specified Condition
|
| 1 - 2
|
20°C (68°F)
|
120 to 280 kΩ
|
- Accelerator Pedal:
| Accelerator Pedal Operation
|
Accelerator Position No. 1
|
Accelerator Position No. 2
|
| Released
|
0.5 to 1.1 V
|
1.2 to 2.0 V
|
| Depressed
|
2.6 to 4.5 V
|
3.4 to 5.3 V
|
- Air Fuel Ratio Sensor (for Bank 1):
| Tester Connection
|
Condition
|
Specified Condition
|
| 1 (HA1A) - 2 (+B)
|
20°C (68°F)
|
1.8 to 3.4 Ω
|
| 1 (HA1A) - 4 (A1A-)
|
Always
|
10 kΩ or higher
|
- Air Fuel Ratio Sensor (for Bank 2):
| Tester Connection
|
Condition
|
Specified Condition
|
| 1 (HA2A) - 2 (+B)
|
20°C (68°F)
|
1.8 to 3.4 Ω
|
| 1 (HA2A) - 4 (A2A-)
|
Always
|
10 kΩ or higher
|
- Heated Oxygen Sensor (for Bank 1):
| Tester Connection
|
Condition
|
Specified Condition
|
| 1 (HT1B) - 2 (+B)
|
20°C (68°F)
|
11 to 16 Ω
|
| 1 (HT1B) - 4 (E2)
|
Always
|
10 kΩ or higher
|
- Heated Oxygen Sensor (for Bank 2):
| Tester Connection
|
Condition
|
Specified Condition
|
| 1 (HT2B) - 2 (+B)
|
20°C (68°F)
|
11 to 16 Ω
|
| 1 (HT2B) - 4 (E2)
|
Always
|
10 kΩ or higher
|
- No. 1 Integration Relay (C/OPN):
| Tester Connection
|
Condition
|
Specified Condition
|
| 1V-6 - 1W-10
|
Battery voltage not applied to terminals 1V-7 and 1W-12
|
10 kΩ or higher
|
| Battery voltage applied to terminals 1V-7 and 1W-12
|
Below 1 Ω
|
- No. 1 Integration Relay (IG2):
| Tester Connection
|
Condition
|
Specified Condition
|
| 1S-1 - 1V-1
|
Battery voltage not applied to terminals 1V-2 and 1W-4
|
10 kΩ or higher
|
| Battery voltage applied to terminals 1V-2 and 1W-4
|
Below 1 Ω
|
- No. 1 Integration Relay (EFI MAIN NO. 1):
| Tester Connection
|
Condition
|
Specified Condition
|
| 1W-7 - 1W-10
|
Battery voltage not applied to terminals 1W-4 and 1W-8
|
10 kΩ or higher
|
| Battery voltage not applied to terminals 1W-4 and 1W-8
|
Below 1 Ω
|
- No. 1 Integration Relay (A/F):
| Tester Connection
|
Condition
|
Specified Condition
|
| 1S-1 - 1W-3
|
Battery voltage not applied to terminals 1W-2 and 1W-4
|
10 kΩ or higher
|
| Battery voltage not applied to terminals 1W-2 and 1W-4
|
Below 1 Ω
|
- No. 1 Integration Relay (AIR PMP HTR):
| Tester Connection
|
Condition
|
Specified Condition
|
| 1S-1 - 1T-12
|
Battery voltage not applied to terminals 1T-8 and 1T-11
|
10 kΩ or higher
|
| Battery voltage not applied to terminals 1T-8 and 1T-11
|
Below 1 Ω
|
- No. 1 Integration Relay (AI VSV):
| Tester Connection
|
Condition
|
Specified Condition
|
| 1S-1 - 1U-2
|
Battery voltage not applied to terminals 1U-1 and 1U-3
|
10 kΩ or higher
|
| Battery voltage not applied to terminals 1U-1 and 1U-3
|
Below 1 Ω
|
- Spark Plug:
| Recommended spark plug
|
Correct electrode gap for new spark plug
|
Maximum electrode gap for used spark plug
|
Standard insulation resistance
|
| SK16HR11
|
Correct electrode gap for new spark plug 1.0 to 1.1 mm (0.0394 to 0.0433in.)
|
1.3 mm (0.0512 in.)
|
10 MΩ or higher
|