RM27T0E
_V1
General
_053654
SPECIFICATIONS
_0260315
2TR-FE ENGINE CONTROL
F
SPECIFICATIONS 2TR-FE ENGINE CONTROL SERVICE DATA
IGNITION SYSTEM
| Spark plug
|
Electrode gap
|
Maximum
|
1.1 mm (0.0433 in.)
|
| Standard
|
0.7 to 0.8 mm (0.0276 to 0.0315 in.)
|
CAMSHAFT OIL CONTROL VALVE
| Camshaft timing oil control valve
|
Standard resistance
|
1 - 2
|
20°C (68°F)
|
6.9 to 7.9 Ω
|
THROTTLE BODY
| Throttle body with motor assembly
|
Standard resistance
|
1 (M-) - 2 (M+)
|
20°C (68°F)
|
0.3 to 100 Ω
|
MASS AIR FLOW METER
| Intake mass air flow meter sub-assembly
|
Standard resistance
|
4 (THA) - 5 (E2)
|
-20°C (-4°F)
|
12.5 to 16.9 kΩ
|
| 20°C (68°F)
|
2.19 to 2.67 kΩ
|
| 60°C (140°F)
|
0.50 to 0.68 kΩ
|
CRANKSHAFT POSITION SENSOR
| Crankshaft position sensor
|
Standard resistance
|
1 (NE+) - 2 (NE-)
|
Cold
(Approximately -10 to 50°C (14 to 122°F)
|
1630 to 2740 Ω
|
Hot
(Approximately 50 to 100°C (122 to 212°F)
|
2065 to 3225 Ω
|
ENGINE COOLANT TEMPERATURE SENSOR
| Engine coolant temperature sensor
|
Standard resistance
|
1 (E2) - 2 (THW)
|
20°C (68°F)
|
2.32 to 2.59 kΩ
|
| 80°C (176°F)
|
0.310 to 0.326 kΩ
|
KNOCK SENSOR
| Knock sensor
|
Standard resistance
|
1 (Ground) - 2 (Output)
|
20°C (68°F)
|
120 to 280 kΩ
|
AIR FUEL RATIO SENSOR
| Air fuel ratio sensor
|
Standard resistance
|
1 (HA1A) - 2 (+B)
|
20°C (68°F)
|
1.6 to 3.2 Ω
|
HEATED OXYGEN SENSOR
| Heated oxygen sensor
|
Standard resistance
|
1 (HT1B) - 2 (+B)
|
20°C (68°F)
|
5 to 8 Ω
|
- INJ NO. 2 Relay:
| Tester Connection
|
Condition
|
Specified Condition
|
| 3 - 5
|
Battery voltage is not applied to terminals 1 and 2
|
10 kΩ or higher
|
| Battery voltage is applied to terminals 1 and 2
|
Below 1 Ω
|
- No. 1 Integration Relay (C/OPN):
| Tester Connection
|
Condition
|
Specified Condition
|
| 1V-6 - 1W-10
|
Battery voltage not applied to terminals 1V-7 and 1W-12
|
10 kΩ or higher
|
| Battery voltage applied to terminals 1V-7 and 1W-12
|
Below 1 Ω
|
- No. 1 Integration Relay (AIR PMP HTR):
| Tester Connection
|
Condition
|
Specified Condition
|
| 1S-1 - 1T-12
|
Battery voltage not applied to terminals 1T-8 and 1T-11
|
10 kΩ or higher
|
| Battery voltage not applied to terminals 1T-8 and 1T-11
|
Below 1 Ω
|
- No. 1 Integration Relay (IG2):
| Tester Connection
|
Condition
|
Specified Condition
|
| 1S-1 - 1V-1
|
Battery voltage not applied to terminals 1V-2 and 1W-4
|
10 kΩ or higher
|
| Battery voltage applied to terminals 1V-2 and 1W-4
|
Below 1 Ω
|
- No. 1 Integration Relay (EFI MAIN NO. 1):
| Tester Connection
|
Condition
|
Specified Condition
|
| 1W-7 - 1W-10
|
Battery voltage not applied to terminals 1W-4 and 1W-8
|
10 kΩ or higher
|
| Battery voltage not applied to terminals 1W-4 and 1W-8
|
Below 1 Ω
|
- No. 1 Integration Relay (A/F):
| Tester Connection
|
Condition
|
Specified Condition
|
| 1S-1 - 1W-3
|
Battery voltage not applied to terminals 1W-2 and 1W-4
|
10 kΩ or higher
|
| Battery voltage not applied to terminals 1W-2 and 1W-4
|
Below 1 Ω
|