Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM (for Camera built-in ECU) › 2017.08–2020.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261016 PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU) C

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU)  C1625  Open or Short in Steering Angle Sensor +B  


DESCRIPTION

This DTC is stored if the rear television camera assembly receives a signal via CAN communication from the steering sensor that indicates a power supply problem.

DTC Code DTC Detection Condition Trouble Area
C1625 Open or short in steering sensor power source
·

Harness or connector

·

Steering sensor



WIRING DIAGRAM

E433918E01
1.125,3.219 2.875,3.396 1.75,0.177 10 false : CAN Communication Line 3.229,0.604 3.583,0.781 0.354,0.177 10 false BAT 3.229,1.708 3.563,1.885 0.333,0.177 10 false ESS 5.063,2.198 7.104,2.417 2.042,0.219 10 false Navigation Receiver Assembly 2.031,1.344 3.042,1.521 1.01,0.177 10 false ECU-IG NO.1 2.271,0.813 2.802,1.01 0.531,0.198 10 false ECU-B 0.438,1.167 1.813,1.396 1.375,0.229 10 false from IG1 NO.1 Relay 0.927,0.625 1.844,0.823 0.917,0.198 10 false from Battery 3.188,2.365 4.729,2.781 1.542,0.417 10 false Steering Sensor 3.031,0.51 3.156,0.688 0.125,0.177 10 false 5 3.031,1.052 3.156,1.229 0.125,0.177 10 false 4 3.031,1.604 3.25,1.792 0.219,0.188 10 false 1 3.229,1.156 3.531,1.333 0.302,0.177 10 false IG 3.177,2.177 3.74,2.427 0.563,0.25 10 false G205

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When "System initializing" is displayed on the navigation receiver assembly after disconnecting the cable from the negative (-) battery terminal, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM (for Camera built-in ECU)>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM (for Camera built-in ECU)>CALIBRATION).

·

The parking assist monitor system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the parking assist monitor system after confirming that the communication system is functioning properly (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEERING SENSOR - BATTERY AND BODY GROUND)
a.
E376978C03
1.469,0.229 1.938,0.458 0.469,0.229 1.917,1.229 2.417,0.865 2.417,0.865 2.604,0.865 true 2.104,1.375 2.375,1.74 2.375,1.74 2.531,1.74 true 1.271,1.24 0.948,0.99 0.948,0.99 0.781,0.99 true 0.125,0.083 0.438,0.24 0.313,0.156 10 false *a 0.458,0.917 0.802,1.083 0.344,0.167 10 false ESS 2.604,1.656 2.948,1.823 0.344,0.167 10 false BAT 2.656,0.792 2.927,0.938 0.271,0.146 10 false IG 1.542,0.271 1.938,0.438 0.396,0.167 10 false G205

Disconnect the G205 steering sensor connector (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>STEERING ANGLE SENSOR>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G205-1 (ESS) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G205-4 (IG) - Body ground Engine switch on (IG) 11 to 14 V
G205-5 (BAT) - Body ground Always 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Steering Sensor)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR