Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM › from 2017.08
RM27T0E _55 Steering _053718 STEERING COLUMN _0260955 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM U

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  DATA LIST / ACTIVE TEST  


READ DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Tilt & Telescopic / Data List.


f.

According to the display on the GTS, read the Data List.

Body Electrical > Tilt&Telescopic > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tilt Position Current tilt position data Min.: 0
Max.: 65535
28672 to 36864 -
Telesco Position Current telescopic position data Min.: 0
Max.: 65535
28672 to 36864 -
Tilt Return Position Memorized tilt return position data Min.: 0
Max.: 65535
28672 to 36864 -
Telesco Return Position Memorized telescopic return position data Min.: 0
Max.: 65535
28672 to 36864 -
Tilt Memory Pos 1 Tilt data of memory position 1 Min.: 0
Max.: 65535
28672 to 36864 -
Telesco Memory Pos 1 Telescopic data of memory position 1 Min.: 0
Max.: 65535
28672 to 36864 -
Tilt Memory Pos 2 Tilt data of memory position 2 Min.: 0
Max.: 65535
28672 to 36864 -
Telesco Memory Pos 2 Telescopic data of memory position 2 Min.: 0
Max.: 65535
28672 to 36864 -
Tilt Memory Pos 3 Tilt data of memory position 3 Min.: 0
Max.: 65535
28672 to 36864 This item is not related to this vehicle
Telesco Memory Pos 3 Telescopic data of memory position 3 Min.: 0
Max.: 65535
28672 to 36864 This item is not related to this vehicle
Tilt Up Limit Uppermost tilt position Not Mem or Mem Not Mem: Position not memorized
Mem: Position memorized
-
Tilt Up Limit Position Uppermost tilt position data Min.: 0
Max.: 65535
28672 to 36864 -
Tilt Down Limit Lowermost tilt position Not Mem or Mem Not Mem: Position not memorized
Mem: Position memorized
-
Tilt Down Limit Position Lowermost tilt position data Min.: 0
Max.: 65535
28672 to 36864 -
Telesco Short Limit Shortest telescopic position Not Mem or Mem Not Mem: Position not memorized
Mem: Position memorized
-
Telesco Short Limit Pos Shortest telescopic position data Min.: 0
Max.: 65535
28672 to 36864 -
Telesco Long Limit Longest telescopic position Not Mem or Mem Not Mem: Position not memorized
Mem: Position memorized
-
Telesco Long Limit Pos Longest telescopic position data Min.: 0
Max.: 65535
28672 to 36864 -
Tilt Up Switch Input state of tilt up switch ON or OFF ON: Tilt up switch activated
OFF: Tilt up switch not activated
Tilt Up SW(CAN) Input state of tilt up switch ON or OFF - This item is not related to this vehicle
Tilt Down Switch Input state of tilt down switch ON or OFF ON: Tilt down switch activated
OFF: Tilt down switch not activated
-
Tilt Down SW(CAN) Input state of tilt down switch ON or OFF - This item is not related to this vehicle
Telesco Short Switch Input state of telescopic contract switch ON or OFF ON: Telescopic contract switch activated
OFF: Telescopic contract switch not activated
-
Telesco Short SW(CAN) Input state of telescopic contract switch ON or OFF - This item is not related to this vehicle
Telesco Long Switch Input state of telescopic extend switch ON or OFF ON: Telescopic extend switch activated
OFF: Telescopic extend switch not activated
-
Telesco Long SW(CAN) Input state of telescopic extend switch ON or OFF - This item is not related to this vehicle
T&T Manual SW Data Voltage data of tilt and telescopic switch Min.: 0.00 V
Max.: 4.99 V
Neutral position: Below 0.20 V
Tilt up: 1.67 to 2.13 V
Tilt down: 0.54 to 0.74 V
Telescopic contract: 1.08 to 1.40 V
Telescopic extend: 2.22 to 2.77 V
-
S/B Mem1 Tilt and telescopic memory position 1 Not Mem or Mem Not Mem: Position not memorized
Mem: Position memorized
-
S/B Mem2 Tilt and telescopic memory position 2 Not Mem or Mem Not Mem: Position not memorized
Mem: Position memorized
-
S/B Mem3 Tilt and telescopic memory position 3 Not Mem or Mem Not Mem: Position not memorized
Mem: Position memorized
This item is not related to this vehicle
T&T Autoaway Function Auto away/return function ON or OFF ON: Auto away/return function allowed
OFF: Auto away/return function prohibited
-
Power Source Voltage Voltage data of power supply Min.: 0.00 V
Max.: 19.99 V
11.00 to 14.00 V -
Freeze Speed Info Vehicle speed data Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual vehicle speed -
IG Switch (CAN) Communication state of ignition switch ON or OFF ON: Communication normal
OFF: Communication interrupted
-
IG Switch Input state of ignition switch ON or OFF ON: Input signal normal
OFF: Input signal interrupted
-
Receive from Meter Communication state of combination meter assembly signal OK or Interpt OK: Communication normal
Interpt: Communication interrupted
-
Receive from Seat ECU Communication state of position control ECU and switch assembly (driver seat) signal OK or Interpt OK: Communication normal
Interpt: Communication interrupted
-
Receive from Combi Communication state of combination switch ECU signal OK or Interpt OK: Communication normal
Interpt: Communication interrupted
This item is not related to this vehicle
J/B Communication state of main body ECU (multiplex network body ECU) signal OK or Interpt OK: Communication normal
Interpt: Communication interrupted
-
Driver Information 1 Driver Information 1 Not Mem or Mem - -
Driver 1 Tilt Mem Driver tilt memory position 1 Min.: 0
Max.: 65535
- -
Driver 1 Telesco Mem Driver telescopic memory position 1 Min.: 0
Max.: 65535
- -
Driver Information 2 Driver Information 2 Not Mem or Mem - -
Driver 2 Tilt Mem Driver tilt memory position 2 Min.: 0
Max.: 65535
- -
Driver 2 Telesco Mem Driver telescopic memory position 2 Min.: 0
Max.: 65535
- -
Driver Information 3 Driver Information 3 Not Mem or Mem - This item is not related to this vehicle
Driver 3 Tilt Mem Driver tilt memory position 3 Min.: 0
Max.: 65535
- This item is not related to this vehicle
Driver 3 Telesco Mem Driver telescopic memory position 3 Min.: 0
Max.: 65535
- This item is not related to this vehicle
Handle Position Steering wheel position signal Away or Return Away: Steering wheel in away position
Return: Steering wheel in return position
-
The Number of DTCs Number of stored DTCs Min.: 0
Max.: 255
Actual number of stored DTCs -



ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Tilt & Telescopic / Active Test.


f.

According to the display on the GTS, perform the Active Test.

Body Electrical > Tilt&Telescopic > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Tilt Operation Tilt operation UP/DOWN -
Telesco Operation Telescopic operation LONG/SHORT -