Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM › from 2017.08
RM27T0E _55 Steering _053718 STEERING COLUMN _0260955 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM C

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  B2620  ECU Power Source Circuit Malfunction  


DESCRIPTION

The ECU power source circuit supplies positive (+) voltage to the multiplex tilt and telescopic ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2620 ECU Power Source Circuit Malfunction The voltage of the ECU power source drops to 8 V or less and this condition continues for 10 seconds or more.
·

Harness or connector

·

Multiplex tilt and telescopic ECU



WIRING DIAGRAM

C268477E62
3.74,0.896 4.406,1.115 0.667,0.219 10 false ECU-B 0.552,0.719 1.406,0.917 0.854,0.198 10 false from Battery 5.594,0.719 6.469,1.052 0.875,0.333 10 false ECUB 5.583,2.427 6.063,2.708 0.479,0.281 10 false GND2 5.354,0.625 5.531,0.896 0.177,0.271 10 false 9 5.365,2.333 5.542,2.552 0.177,0.219 10 false 8 5.427,2.969 5.979,3.208 0.552,0.24 10 false G211 5.427,3.135 6.51,3.573 1.083,0.438 10 false Multiplex Tilt and Telescopic ECU

CAUTION / NOTICE / HINT

HINT:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY)
a.
C387819C03
1.469,0.281 1.917,0.521 0.448,0.24 0.979,1.229 0.938,1.615 0.938,1.615 0.771,1.615 true 1.531,0.323 2.146,0.521 0.615,0.198 10 false G211 0.365,1.542 0.979,1.74 0.615,0.198 10 false ECUB
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


Disconnect the G211 multiplex tilt and telescopic ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G211-9 (ECUB) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)
a.
C387819C04
1.469,0.281 1.917,0.521 0.448,0.24 0.771,1.229 0.729,1.615 0.729,1.615 0.563,1.615 true 1.531,0.323 2.146,0.521 0.615,0.198 10 false G211 0.167,1.531 0.781,1.729 0.615,0.198 10 false GND2
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


Disconnect the G211 multiplex tilt and telescopic ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G211-8 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR