Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM › from 2017.08
RM27T0E _55 Steering _053718 STEERING COLUMN _0260955 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM J

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  IG Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, the IG power source circuit supplies positive (+) voltage to the multiplex tilt and telescopic ECU.

The multiplex tilt and telescopic ECU also receives ignition switch signals via this circuit.

WIRING DIAGRAM

C244378E52
3.708,0.802 4.885,1.021 1.177,0.219 10 false ECU-IG NO. 1 0.625,0.635 1.646,0.896 1.021,0.26 10 false from IG Circuit 5.792,0.635 6.667,0.969 0.875,0.333 10 false IG 5.781,2.333 6.26,2.615 0.479,0.281 10 false GND2 5.51,0.542 5.698,0.729 0.188,0.188 10 false 10 5.594,2.24 5.844,2.417 0.25,0.177 10 false 8 5.781,1.417 6.26,1.698 0.479,0.281 10 false GND 5.594,1.323 5.844,1.5 0.25,0.177 10 false 1 5.604,2.865 6.198,3.094 0.594,0.229 10 false G211 5.604,3.031 6.688,3.469 1.083,0.438 10 false Multiplex Tilt and Telescopic ECU

CAUTION / NOTICE / HINT

HINT:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY)
a.
C387819C06
1.469,0.281 1.917,0.521 0.448,0.24 1.188,1.24 1.146,1.625 1.146,1.625 0.979,1.625 true 1.531,0.323 2.146,0.521 0.615,0.198 10 false G211 0.802,1.552 1.417,1.75 0.615,0.198 10 false IG
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


Disconnect the G211 multiplex tilt and telescopic ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G211-10 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)
a.
C387819C01
1.469,0.281 1.917,0.521 0.448,0.24 0.802,0.979 0.719,0.677 0.719,0.677 0.552,0.677 true 0.771,1.229 0.729,1.615 0.729,1.615 0.563,1.615 true 1.531,0.323 2.146,0.521 0.615,0.198 10 false G211 0.167,1.531 0.781,1.729 0.615,0.198 10 false GND2 0.219,0.604 0.833,0.802 0.615,0.198 10 false GND
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


Disconnect the G211 multiplex tilt and telescopic ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G211-1 (GND) - Body ground Always Below 1 Ω
G211-8 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR