Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261011 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1ABE  Short to GND or Open in Buzzer  


DESCRIPTION

DTC C1ABE is stored when the blind spot monitor sensor RH detects a ground short or open in RCTA buzzer (blind spot monitor buzzer) circuit.

DTC Code DTC Detection Condition Trouble Area
C1ABE

Both of the following conditions are met:

-

Blind spot monitor system is on with engine switch on (IG).

-

The current flowing to the buzzer is below a specified value when buzzer operation voltage is being sent to the buzzer.



·

Blind spot monitor sensor RH

·

RCTA buzzer (blind spot monitor buzzer)

·

Harness or connector



WIRING DIAGRAM

E254403E63
0.156,1.021 1.563,1.219 1.406,0.198 10 false from IG1 NO. 1 Relay 3.521,1.021 3.813,1.219 0.292,0.198 10 false BZP 3.177,1.313 3.521,1.51 0.344,0.198 10 false R44 3.177,1.479 4.74,1.813 1.563,0.333 10 false RCTA Buzzer (Blind Spot Monitor Buzzer) 5.615,1.927 5.906,2.125 0.292,0.198 10 false R43 5.615,2.083 6.813,2.448 1.198,0.365 10 false Blind Spot Monitor Sensor RH 4.344,1.021 4.677,1.219 0.333,0.198 10 false BZN 3.333,0.906 3.479,1.083 0.146,0.177 10 false 1 5.646,1.021 5.979,1.219 0.333,0.198 10 false BUZ 5.479,0.917 5.625,1.094 0.146,0.177 10 false 3 4.698,0.917 4.844,1.094 0.146,0.177 10 false 2 2.406,1.188 2.729,1.385 0.323,0.198 10 false IG1

CAUTION / NOTICE / HINT

NOTICE:
·

When checking for DTCs, make sure that the blind spot monitor system is on.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK DTC

b.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

NG

2.CHECK HARNESS AND CONNECTOR (RCTA BUZZER - BATTERY AND BLIND SPOT MONITOR SENSOR RH)
2.CHECK HARNESS AND CONNECTOR (RCTA BUZZER - BATTERY AND BLIND SPOT MONITOR SENSOR RH)
a.

Disconnect the R44 RCTA buzzer (blind spot monitor buzzer) connector.


b.

Disconnect the R43 blind spot monitor sensor RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R44-2 (BZN) - R43-3 (BUZ) Always Below 1 Ω
R44-2 (BZN) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R44-1 (BZP) - Body ground Engine switch on (IG) 11 to 14 V
R44-1 (BZP) - Body ground Engine switch off Below 1 V




OK

3.REPLACE BLIND SPOT MONITOR BUZZER (RCTA BUZZER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE BLIND SPOT MONITOR BUZZER (RCTA BUZZER)
a.

Replace the RCTA buzzer (blind spot monitor buzzer) with a new or normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SENSOR>REMOVAL).



NEXT

4.CHECK DTC
4.CHECK DTC

b.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

END (RCTA BUZZER [BLIND SPOT MONITOR BUZZER] IS DEFECTIVE)

NG