Home › Brake › BRAKE SYSTEM (OTHER) › HYDRAULIC BRAKE BOOSTER(for RHD) › from 2017.08
RM27T0E _54 Brake _053713 BRAKE SYSTEM (OTHER) _0260931 HYDRAULIC BRAKE BOOSTER(for RHD) G

BRAKE SYSTEM (OTHER)  HYDRAULIC BRAKE BOOSTER(for RHD)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 47217 1.INSPECT BRAKE MASTER CYLINDER FLUID PRESSURE CHANGE

a.
C354137E01
1.51,0.417 1.51,0.219 1.51,0.219 1.719,0.219 false 0.302,0.563 0.302,0.365 0.302,0.365 0.51,0.365 false 3.104,0.531 3.104,0.333 3.104,0.333 2.917,0.333 false 1.76,0.125 2.073,0.323 0.313,0.198 10 false *a 0.573,0.281 0.885,0.479 0.313,0.198 10 false SST 2.583,0.26 2.885,0.438 0.302,0.177 10 false SST

Inspect the battery voltage.

Standard Voltage:

11 to 14 V



b.

Turn the ignition switch off and depress the brake pedal more than 40 times.

HINT:

When pressure in the power supply system is released, the reaction force decreases and the stroke becomes longer.



c.

Install the LSPV gauge (SST) and brake pedal effort gauge, and bleed air from the LSPV gauge (SST).

SST
09709-29018  

Text in Illustration
*a Brake Pedal Effort Gauge


d.

When the booster does not operate:

Depress the brake pedal and check the fluid pressure.

Standard Fluid Pressure with Pedal Depressing Force of 245 N (25 kgf, 55 lbf):
Front Brake Pressure Rear Brake Pressure
2090 kPa (21.3 kgf/cm2, 303 psi) or more 0 kPa (0 kgf/cm2, 0 psi)


Standard Fluid Pressure with Pedal Depressing Force of 343 N (35 kgf, 77 lbf):
Front Brake Pressure Rear Brake Pressure
3090 kPa (31.5 kgf/cm2, 448psi) or more 0 kPa (0 kgf/cm2, 0 psi)



e.

When the booster operates:

i.

Turn the ignition switch to ON and wait until the pump motor has stopped.


ii.

Depress the brake pedal and check the fluid pressure.

Standard Fluid Pressure with Pedal Depressing Force of 49 N (5 kgf, 11 lbf):
Front Brake Pressure Rear Brake Pressure
1809 to 2211 kPa
(18.4 to 22.5 kgf/cm2, 262 to 320 psi)
1998 to 2442 kPa
(20.4 to 24.9 kgf/cm2, 290 to 354 psi)


Standard Fluid Pressure with Pedal Depressing Force of 98 N (10 kgf, 22 lbf):
Front Brake Pressure Rear Brake Pressure
4059 to 4961 kPa
(41.4 to 50.5 kgf/cm2, 589 to 719 psi)
4338 to 5302 kPa
(44.2 to 54.0 kgf/cm2, 629 to 768 psi)


Standard Fluid Pressure with Pedal Depressing Force of 147 N (15 kgf, 33 lbf):
Front Brake Pressure Rear Brake Pressure
6309 to 7711 kPa
(64.3 to 78.6 kgf/cm2, 915 to 1118 psi)
6669 to 8151 kPa
(68.0 to 83.1 kgf/cm2, 967 to 1181 psi)


Standard Fluid Pressure with Pedal Depressing Force of 196 N (20 kgf, 44 lbf):
Front Brake Pressure Rear Brake Pressure
8550 to 10450 kPa
(87.2 to 106.5 kgf/cm2, 1240 to 1515 psi)
9360 to 11440 kPa
(95.4 to 116.6 kgf/cm2, 1357 to 1658 psi)




Hide 47217 2.INSPECT BRAKE MASTER CYLINDER OPERATION

a.

Inspect the battery voltage.

Standard Voltage:

11 to 14 V



b.

Turn the ignition switch off and depress the brake pedal more than 20 times.

HINT:

When pressure in the power supply system is released, the reaction force decreases and the stroke becomes longer.



c.

Check that the brake pedal reaction force decreases.

If the pedal reaction force does not decrease, check the brake line and brake master cylinder and replace parts as necessary.


d.

Turn the ignition switch to ON and check the pump motor operation noise.

If the pump motor does not operate, check the wire harness and brake booster pump assembly and replace parts as necessary (See page Brake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER(for RHD)>REMOVAL).


e.

Connect the intelligent tester to the DLC3.


f.

Turn the ignition switch to ON.


g.

Turn the intelligent tester on.


h.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.


i.

Jack up and support the vehicle.


j.

Release the parking brake lever.


k.

Move the shift lever to N and check that the rear wheels can be rotated by hand.


l.

Inspect the front VSC solenoid (SMCF) operation.

i.

Select "VSC/TRC Solenoid (SRCF)" on the intelligent tester.


ii.

Turn "VSC/TRC Solenoid (SRCF)" on with the intelligent tester, depress the brake pedal with a stable force and check that the pedal cannot be depressed.

If the pedal can be depressed, replace the brake master cylinder.

NOTICE:

When operating the solenoid continuously, set the interval to more than 20 seconds.


HINT:

To protect the solenoids, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.



iii.

Release the brake pedal.


iv.

When the solenoid is off, depress the brake pedal again and check that the brake pedal can be depressed.

If the pedal cannot be depressed, replace the brake master cylinder.



m.

Inspect the front VSC solenoid (SREA) operation.

i.

Select "VSC/TRC Solenoid (SRCR)" and "VSC/TRC Solenoid (SRCF)" on the intelligent tester.


ii.

Turn "VSC/TRC Solenoid (SRCR)" and "VSC/TRC Solenoid (SRCF)" on simultaneously with the intelligent tester, and then depress the brake pedal with a stable force.


iii.

When the solenoids are on, check that the front wheels cannot be rotated by hand.

If the front wheels can be rotated, replace the brake master cylinder.

NOTICE:

When operating the solenoid continuously, set the interval to more than 20 seconds.


HINT:
·

To protect the solenoids, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.

·

When rotating the wheels quickly, the fail-safe function is activated and judgment cannot be made properly. Rotate the wheels as slowly as possible.




iv.

When the solenoids are off, turn "VSC/TRC Solenoid (SRCF)" on again, and then depress the brake pedal. Check the front wheels by rotating them by hand.

If the front wheels cannot be rotated, replace the brake master cylinder.


v.

When "VSC/TRC Solenoid (SRCF)" is off, depress the brake pedal again and check that the brake pedal can be depressed.

If the pedal cannot be depressed, replace the brake master cylinder.



n.

Inspect the front ABS solenoid (SFRH) operation.

i.

Select "ABS Solenoid (SFRH)" on the intelligent tester.


ii.

Turn "ABS Solenoid (SFRH)" on with the intelligent tester, and then depress the brake pedal with a stable force.


iii.

When the solenoid is on, check the right front wheel by rotating it by hand.

If the right front wheel cannot be rotated, replace the brake master cylinder.

NOTICE:

When operating the solenoid continuously, set the interval to more than 20 seconds.


HINT:
·

To protect the solenoids, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.

·

When rotating the wheel quickly, the fail-safe function is activated and judgment cannot be made properly. Rotate the wheel as slowly as possible.




iv.

When the solenoid is off, depress the brake pedal again and check that the right front wheel cannot be rotated by hand.

If the right front wheel can be rotated, replace the brake master cylinder.

HINT:

When rotating the wheel quickly, the fail-safe function is activated and judgment cannot be made properly. Rotate the wheel as slowly as possible.




o.

Inspect the front ABS solenoid (SFLH) operation.

i.

Select "ABS Solenoid (SFLH)" on the intelligent tester.


ii.

Turn "ABS Solenoid (SFLH)" on with the intelligent tester, and then depress the brake pedal with a stable force.


iii.

When the solenoid is on, check the left front wheel by rotating it by hand.

If the left front wheel cannot be rotated, replace the brake master cylinder.

NOTICE:

When operating the solenoid continuously, set the interval to more than 20 seconds.


HINT:
·

To protect the solenoids, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.

·

When rotating the wheel quickly, the fail-safe function is activated and judgment cannot be made properly. Rotate the wheel as slowly as possible.




iv.

When the solenoid is off, depress the brake pedal again and check that the left front wheel cannot be rotated by hand.

If the left front wheel can be rotated, replace the brake master cylinder.



p.

Inspect the front ABS solenoid (SFRR) operation.

i.

Select "ABS Solenoid (SFRR)" and "ABS Solenoid (SFRH)" on the intelligent tester.


ii.

Depress the brake pedal with a stable force, and then turn "ABS Solenoid (SFRR)" and "ABS Solenoid (SFRH)" on simultaneously with the intelligent tester.


iii.

When the solenoids are on, check the right front wheel by rotating it by hand.

If the right front wheel cannot be rotated, replace the brake master cylinder.

NOTICE:

When operating the solenoid continuously, set the interval to more than 20 seconds.


HINT:
·

To protect the solenoids, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.

·

When rotating the wheel quickly, the fail-safe function is activated and judgment cannot be made properly. Rotate the wheel as slowly as possible.




iv.

When the solenoids are off, depress the brake pedal again and check that the right front wheel cannot be rotated by hand.

If the right front wheel can be rotated, replace the brake master cylinder.



q.

Inspect the front ABS solenoid (SFLR) operation.

i.

Select "ABS Solenoid (SFLR)" and "ABS Solenoid (SFLH)" on the intelligent tester.


ii.

Depress the brake pedal with a stable force, and then turn "ABS Solenoid (SFLR)" and "ABS Solenoid (SFLH)" on simultaneously with the intelligent tester.


iii.

When the solenoids are on, check the left front wheel by rotating it by hand.

If the left front wheel cannot be rotated, replace the brake master cylinder.

NOTICE:

When operating the solenoid continuously, set the interval to more than 20 seconds.


HINT:
·

To protect the solenoids, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.

·

When rotating the wheel quickly, the fail-safe function is activated and judgment cannot be made properly. Rotate the wheel as slowly as possible.




iv.

When the solenoids are off, depress the brake pedal again and check that the left front wheel cannot be rotated by hand.

If the left front wheel can be rotated, replace the brake master cylinder.



r.

Inspect the rear VSC solenoid (SREC) operation.

i.

Select "VSC/TRC Solenoid (SRMF)" on the intelligent tester.


ii.

Depress the brake pedal with a stable force, and then turn "VSC/TRC Solenoid (SRMF)" on with the intelligent tester.


iii.

Release the brake pedal when the solenoid is on, and check that the rear wheels cannot be rotated by hand.

If the rear wheels can be rotated, replace the brake master cylinder.

NOTICE:

When operating the solenoid continuously, set the interval to more than 20 seconds.


HINT:
·

To protect the solenoids, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.

·

When rotating the wheels quickly, the fail-safe function is activated and judgment cannot be made properly. Rotate the wheels as slowly as possible.




iv.

When the solenoid is off, check the rear wheels by rotating them by hand.

If the rear wheels cannot be rotated, replace the brake master cylinder.



s.

Inspect the rear VSC solenoid (STR) operation.

i.

Select "VSC/TRC Solenoid (SRMR)" and "VSC/TRC Solenoid (SRMF)" on the intelligent tester.


ii.

Turn "VSC/TRC Solenoid (SRMR)" and "VSC/TRC Solenoid (SRMF)" on simultaneously with the intelligent tester.


iii.

When the solenoids are on, check that the rear wheels cannot be rotated by hand.

If the rear wheels can be rotated, replace the brake master cylinder.

NOTICE:

When operating the solenoid continuously, set the interval to more than 20 seconds.


HINT:
·

To protect the solenoids, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.

·

When rotating the wheels quickly, the fail-safe function is activated and judgment cannot be made properly. Rotate the wheels as slowly as possible.




iv.

When the solenoids are off, turn "VSC/TRC Solenoid (SRMF)" on again, and check the rear wheels by rotating them by hand.

If the rear wheels cannot be rotated, replace the brake master cylinder.


v.

When "VSC/TRC Solenoid (SRMF)" is off, depress the brake pedal again and check that the rear wheels cannot be rotated by hand.

If the rear wheels can be rotated, replace the brake master cylinder.



t.

Inspect the rear ABS solenoid (SRRH) operation.

i.

Select "ABS Solenoid (SRRH)" on the intelligent tester.


ii.

Turn "ABS Solenoid (SRRH)" on with the intelligent tester, and then depress the brake pedal with a stable force.


iii.

When the solenoid is on, check the right rear wheel by rotating it by hand.

If the right rear wheel cannot be rotated, replace the brake master cylinder.

NOTICE:

When operating the solenoid continuously, set the interval to more than 20 seconds.


HINT:
·

To protect the solenoids, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.

·

When rotating the wheel quickly, the fail-safe function is activated and judgment cannot be made properly. Rotate the wheel as slowly as possible.




iv.

When the solenoid is off, depress the brake pedal again and check that the right rear wheel cannot be rotated by hand.

If the right rear wheel can be rotated, replace the brake master cylinder.

HINT:

When rotating the wheel quickly, the fail-safe function is activated and judgment cannot be made properly. Rotate the wheel as slowly as possible.




u.

Inspect the rear ABS solenoid (SRLH) operation.

i.

Select "ABS Solenoid (SRLH)" on the intelligent tester.


ii.

Turn "ABS Solenoid (SRLH)" on with the intelligent tester, and then depress the brake pedal with a stable force.


iii.

When the solenoid is on, check the left rear wheel by rotating it by hand.

If the left rear wheel cannot be rotated, replace the brake master cylinder.

NOTICE:

When operating the solenoid continuously, set the interval to more than 20 seconds.


HINT:
·

To protect the solenoids, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.

·

When rotating the wheel quickly, the fail-safe function is activated and judgment cannot be made properly. Rotate the wheel as slowly as possible.




iv.

When the solenoid is off, depress the brake pedal again and check that the left rear wheel cannot be rotated by hand.

If the left rear wheel can be rotated, replace the brake master cylinder.



v.

Inspect the rear ABS solenoid (SRRR) operation.

i.

Select "ABS Solenoid (SRRR)" and "ABS Solenoid (SRRH)" on the intelligent tester.


ii.

Depress the brake pedal with a stable force, and then turn "ABS Solenoid (SRRR)" and "ABS Solenoid (SRRH)" on simultaneously with the intelligent tester.


iii.

When the solenoids are on, check the right rear wheel by rotating it by hand.

If the right rear wheel cannot be rotated, replace the brake master cylinder.

NOTICE:

When operating the solenoid continuously, set the interval to more than 20 seconds.


HINT:
·

To protect the solenoids, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.

·

When rotating the wheel too quickly, the fail-safe function is activated and judgment cannot be made properly. Rotate the wheel as slowly as possible.




iv.

When the solenoids are off, depress the brake pedal again and check that the right rear wheel cannot be rotated by hand.

If the right rear wheel can be rotated, replace the brake master cylinder.



w.

Inspect the rear ABS solenoid (SRLR) operation.

i.

Select "ABS Solenoid (SRLR)" and "ABS Solenoid (SRLH)" on the intelligent tester.


ii.

Depress the brake pedal with a stable force, and then turn "ABS Solenoid (SRLR)" and "ABS Solenoid (SRLH)" on simultaneously with the intelligent tester.


iii.

When the solenoids are on, check the left rear wheel by rotating it by hand.

If the left rear wheel cannot be rotated, replace the brake master cylinder.

NOTICE:

When operating the solenoid continuously, set the interval to more than 20 seconds.


HINT:
·

To protect the solenoids, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.

·

When rotating the wheel too quickly, the fail-safe function is activated and judgment cannot be made properly. Rotate the wheel as slowly as possible.




iv.

When the solenoids are off, depress the brake pedal again and check that the left rear wheel cannot be rotated by hand.

If the left rear wheel can be rotated, replace the brake master cylinder.



x.

Lower the vehicle.


y.

Disconnect the intelligent tester.