Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2018.06–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P0097  Intake Air Temperature Sensor 2 Circuit Low Bank 1  P0098  Intake Air Temperature Sensor 2 Circuit High Bank 1  


DESCRIPTION

A429908E03
3.49,2.656 4.125,1.854 4.125,1.854 4.302,1.854 true 2.208,0.813 3.281,1.01 1.073,0.198 10 false Resistance kΩ 3.292,4.365 5.302,4.552 2.01,0.188 10 false Temperature °C (°F) 4.365,1.76 5.896,1.958 1.531,0.198 10 false Acceptable 0.188,0.115 1.26,0.313 1.073,0.198 10 false (Fig. 1) 2.833,3.99 3.448,4.188 0.615,0.198 10 false (-4) 3.156,3.99 3.771,4.188 0.615,0.198 10 false (32) 3.729,3.99 4.344,4.188 0.615,0.198 10 false (104) 3.469,3.99 4.083,4.188 0.615,0.198 10 false (68) 4.042,3.99 4.656,4.188 0.615,0.198 10 false (140) 4.354,3.99 4.969,4.188 0.615,0.198 10 false (176) 4.667,3.99 5.281,4.188 0.615,0.198 10 false (212)

The Intake Air Temperature Sensor (for Intercooler) detects the intake air temperature before the intake air passes through the turbo charger. A built-in thermistor in the sensor changes its resistance value according to the intake air temperature. The lower the intake air temperature, the higher the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (See Fig. 1).

The sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the sensor from terminal THCA via resistor R. Resistor R and the sensor are connected in series. When the resistance value of the sensor changes in accordance with changes in the intake air temperature, the potential at terminal THCA also changes. Based on this signal, the ECM corrects the fuel injection volume to improve driveability with a cold engine.

P0097
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 3 second or more Short in intake air temperature sensor (for intercooler) circuit for 3 seconds.(2 trip detection logic)
·

Short in intake air temperature sensor (for intercooler) circuit

·

Intake air temperature sensor (for intercooler)

·

ECM



P0098
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 3 second or more Short in intake air temperature sensor (for intercooler) circuit for 3 seconds.(2 trip detection logic)
·

Open in intake air temperature sensor (for intercooler) circuit

·

Intake air temperature sensor (for intercooler)

·

ECM



HINT:

When any of DTCs are stored, check the intake air temperature sensor (for intercooler)by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Intake Air Temp B1S2.


Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
215°C (419°F) or more Short circuit

WIRING DIAGRAM

A337317E83
0.448,2.813 1.385,3.052 0.938,0.24 10 false C182 5.563,3.01 6.021,3.208 0.458,0.198 10 false C150 5.583,3.208 6.042,3.406 0.458,0.198 10 false ECM 0.438,3.01 3.313,3.24 2.875,0.229 10 false Intake Air Temperature Sensor (for Intercooler) 5.26,1.333 5.719,1.531 0.458,0.198 10 false THCA 5.26,1.927 5.781,2.125 0.521,0.198 10 false ETCA 2.219,2.188 2.677,2.385 0.458,0.198 10 false 2 2.198,1.594 2.656,1.792 0.458,0.198 10 false 1 4.969,1.552 5.427,1.75 0.458,0.198 10 false 29 4.948,2.156 5.406,2.354 0.458,0.198 10 false 21 5.906,0.948 6.365,1.146 0.458,0.198 10 false 5 V 5.854,1.219 6.313,1.417 0.458,0.198 10 false R

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (INTAKE AIR TEMP B1S2)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp B1S2.


e.

Read the value.


Standard:

Same value as the actual inlet air temperature.


Result:
Result Proceed to
-40°C (-40°F) A
215°C (419°F) or more B
OK (same as air temperature near intake manifold) C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 215°C (419°F) or more.




A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

7.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A430889C02
2.677,1.396 2.99,1.594 0.313,0.198 10 false *2 2.448,0.656 2.958,0.865 0.51,0.208 10 false THCA 2.438,1.146 2.906,1.344 0.469,0.198 10 false ETCA 0.792,1.344 1.104,1.542 0.313,0.198 10 false *1 0.896,2.854 1.208,3.052 0.313,0.198 10 false *a
*1 Intake Air Temperature Sensor (for Intercooler)
*2 ECM
*a Front view of wire harness connector (to Intake Air Temperature Sensor(after turbocharged))


Disconnect the intake air temperature sensor (for intercooler) connector.


b.

Connect terminals 1 and 2 of the intake air temperature sensor (for intercooler) wire harness side connector.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG) and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp B1S2.


f.

Read the value.

OK:

215°C (419°F) or higher



g.

Reconnect the intake air temperature sensor (for intercooler) connector.


Result:
Proceed to
OK
NG



OK

3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER)

NG

4.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER) - ECM)
3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER)
a.

Replace the intake air temperature sensor (for intercooler).

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY
4.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER) - ECM)
a.

Disconnect the intake air temperature sensor (for intercooler) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C182-1 - C150-29 (THCA) Always Below 1 Ω
C182-2 - C150-21 (ETCA) Always Below 1 Ω


d.

Reconnect the intake air temperature sensor (for intercooler) connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY
7.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A302633C44
0.771,0.25 1.083,0.448 0.313,0.198 10 false *1 2.604,0.25 2.917,0.448 0.313,0.198 10 false *2 2.438,1.042 2.927,1.24 0.49,0.198 10 false THCA 2.448,1.51 2.938,1.708 0.49,0.198 10 false ETCA
*1 Intake Air Temperature Sensor (for Intercooler)
*2 ECM


Disconnect the intake air temperature sensor (for intercooler) connector.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG) and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp B1S2.


e.

Read the value.

OK:

-40°C (-40°F)



f.

Reconnect the intake air temperature sensor (for intercooler) connector.


Result:
Proceed to
OK
NG



OK

8.REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER)

NG

10.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER) - ECM)
8.REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER)
a.

Replace the intake air temperature sensor (for intercooler).

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off for 30 seconds or more.


d.

Turn the engine switch on (IG) for 1 second or more.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.



Result:
Proceed to
NEXT



NEXT

END

10.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER) - ECM)
a.

Disconnect the intake air temperature sensor (for intercooler) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
C182-1 or C150-29 (THCA) - Body ground and other terminals Always 10 kΩ or higher

d.

Reconnect the intake air temperature sensor (for intercooler) connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

11.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
11.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY