Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2018.06–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P00E0  Charge Air Cooler Coolant Temperature Sensor Circuit Low  P00E1  Charge Air Cooler Coolant Temperature Sensor Circuit High  


DESCRIPTION

A thermistor is built into the engine coolant temperature sensor (for intercooler) and it changes its resistance value according to the engine coolant temperature.

The structure of the sensor and connection to the ECM is the same as that of the intake air temperature sensor.

P00E0
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 3 second or more Short in the engine coolant temperature sensor (for intercooler) circuit for 3 seconds (1 trip detection logic).
·

Short in engine coolant temperature sensor (for intercooler) circuit

·

Engine coolant temperature sensor (for intercooler)

·

ECM



P00E1
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 3 second or more Open in the engine coolant temperature sensor (for intercooler) circuit for 3 seconds (1 trip detection logic).
·

Open in engine coolant temperature sensor (for intercooler) circuit

·

Engine coolant temperature sensor (for intercooler)

·

ECM



Related Data List
DTC No. Data List
P00E0 Intercooler Coolant Temperature
P00E1

HINT:
·

If DTC P00E0 and/or P00E1 is stored, the following symptoms may appear:

-

Misfire

-

Combustion noise

-

Black smoke

-

White smoke

-

Lack of power


·

When DTC P00E0 and/or P00E1 is stored, check the engine coolant temperature by entering the following menus: Powertrain / Engine and ECT / Data List / Intercooler Coolant Temperature.



Reference
GTS Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) or higher Short circuit

WIRING DIAGRAM

A337317E82
0.448,2.813 1.063,3.031 0.615,0.219 10 false C183 5.563,3.01 6.177,3.229 0.615,0.219 10 false C150 5.583,3.208 6.042,3.406 0.458,0.198 10 false ECM 0.438,3.01 2.667,3.354 2.229,0.344 10 false Engine Coolant Temperature Sensor (for Intercooler) 5.26,1.333 5.719,1.531 0.458,0.198 10 false THIW 5.26,1.917 5.781,2.115 0.521,0.198 10 false ETHIW 2.188,1.313 2.646,1.51 0.458,0.198 10 false 2 2.188,1.948 2.646,2.146 0.458,0.198 10 false 1 5.021,1.333 5.479,1.531 0.458,0.198 10 false 31 5.01,1.917 5.469,2.115 0.458,0.198 10 false 23 5.906,0.948 6.365,1.146 0.458,0.198 10 false 5 V 5.854,1.219 6.313,1.417 0.458,0.198 10 false R

PROCEDURE

1.READ VALUE USING GTS (INTERCOOLER COOLANT TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intercooler Coolant Temperature.


d.

Read the value.


Result:
Result Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
70 to 90°C (158 to 194°F) C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F) or higher.




A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

6.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.

Disconnect the engine coolant temperature sensor (for intercooler) connector.

A412451C04
4.448,1.479 4.938,1.75 0.49,0.271 0.74,0.406 1.052,0.604 0.313,0.198 10 false *1 2.583,0.333 2.896,0.542 0.313,0.208 10 false *2 5,0.615 5.313,0.823 0.313,0.208 10 false *a 4.531,1.531 5.115,1.76 0.583,0.229 10 false C183 2.667,1.219 3.125,1.417 0.458,0.198 12 false THIW 2.688,1.615 3.146,1.813 0.458,0.198 10 false ETHW
*1 Engine Coolant Temperature Sensor
(for Intercooler)
*2 ECM
*a Front view of wire harness connector
(to Engine Coolant Temperature Sensor (for Intercooler))
- -



b.

Connect terminals 1 and 2 of the engine coolant temperature sensor (for intercooler) wire harness side connector.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG) and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intercooler Coolant Temperature.


f.

Read the value.

OK:

140°C (284°F) or higher



g.

Reconnect the engine coolant temperature sensor (for intercooler) connector.


Result:
Proceed to
OK
NG



OK

3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE SENSOR (FOR INTERCOOLER)

NG

4.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR (FOR INTERCOOLER) - ECM)
3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE SENSOR (FOR INTERCOOLER)

Replace the engine coolant temperature sensor (for intercooler).

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR (FOR INTERCOOLER) - ECM)
a.

Disconnect the engine coolant temperature sensor (for intercooler) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
C183-2 - C150-31 (THIW) Always Below 1 Ω
C183-1 - C150-23 (ETIW) Always Below 1 Ω

d.

Reconnect the engine coolant temperature sensor (for intercooler) connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A302633C42
2.469,1.063 2.917,1.323 0.448,0.26 10 false THIW 2.479,1.51 3,1.708 0.521,0.198 10 false ETIW 0.771,0.25 1.083,0.448 0.313,0.198 10 false *1 2.583,0.25 2.896,0.448 0.313,0.198 10 false *2
*1 Engine Coolant Temperature Sensor (for Intercooler)
*2 ECM


Disconnect the engine coolant temperature sensor (for intercooler) connector.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG) and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intercooler Coolant Temperature.


e.

Read the value.

OK:

-40°C (-40°F)



f.

Reconnect the engine coolant temperature sensor (for intercooler) connector.


Result:
Proceed to
OK
NG



OK

7.REPLACE ENGINE COOLANT TEMPERATURE SENSOR (FOR INTERCOOLER)

NG

9.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR (FOR INTERCOOLER) - ECM)
7.REPLACE ENGINE COOLANT TEMPERATURE SENSOR (FOR INTERCOOLER)
a.

Replace the engine coolant temperature sensor (for intercooler) sensor.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch on (IG) for 1 second or more.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.



Result:
Proceed to
NEXT



NEXT

END

9.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR (FOR INTERCOOLER) - ECM)
a.

Disconnect the engine coolant temperature sensor (for intercooler) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.


Tester Connection Condition Specified Condition
C183-2 or C150-31 (THIW) - Body ground and other terminals Always 10 kΩ or higher

d.

Reconnect the engine coolant temperature sensor (for intercooler) connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

10.REPLACE ECM

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED