Home › Engine / Hybrid System › 1GD-FTV (INTAKE / EXHAUST) › COOLANT (w/ Urea SCR System) › from 2018.06
RM27T0E _51 Engine / Hybrid System _053680 1GD-FTV INTAKE / EXHAUST _0358860 COOLANT(w/ Urea SCR System) A

1GD-FTV INTAKE / EXHAUST  COOLANT(w/ Urea SCR System)  REPLACEMENT  


PROCEDURE

Hide 1.DRAIN ENGINE COOLANT

CAUTION:

Do not remove the reservoir cap (for Intercooler) while the engine coolant (for Intercooler) is still hot. Pressurized, hot coolant and steam may be released and cause serious burns.


a.
A421187C02
1.76,1.458 2.25,1.458 false 2.313,1.375 2.625,1.531 0.313,0.156 10 true *a
*a Vinyl Tube


Install a vinyl tube to the radiator drain cock plug (for Intercooler).


b.
A421188C02
1.552,0.844 1.813,0.177 1.813,0.177 2.042,0.177 true 0.156,2.865 0.156,2.646 0.156,2.646 0.26,2.208 true 0.302,0.302 0.458,0.302 0.458,0.302 0.49,0.625 true 2.146,0.094 2.458,0.25 0.313,0.156 10 false *1 0.094,2.917 0.406,3.073 0.313,0.156 10 false *2 0.115,0.219 0.427,0.375 0.313,0.156 10 false *a
*1 Reservoir Cap (for Intercooler)
*2 Radiator Drain Cock Plug (for Intercooler)
*a Bleeder Plug


Loosen the radiator drain cock plug (for Intercooler) and drain the coolant (for Intercooler).

HINT:

Collect the coolant in a container and dispose of it according to the regulations in your area.



c.

Remove the reservoir cap (for Intercooler).


d.

Tighten the radiator drain cock plug (for Intercooler) by hand.


e.

Remove the vinyl tube from the radiator drain cock plug (for Intercooler).


Hide 2.ADD ENGINE COOLANT

CAUTION:

Do not remove the reservoir cap (for Intercooler) while the engine coolant (for Intercooler) is still hot. Pressurized, hot coolant and steam may be released and cause serious burns.


a.

When using the GTS:

i.
A421189C02
1.76,1.125 1.917,1.448 1.917,1.448 2.146,1.448 true 2.198,1.375 2.51,1.531 0.313,0.156 10 true *a
*a Bleeder Plug


Loosen the bleeder plug of the intercooler cooling radiator assembly.


ii.

Slowly pour coolant into the intercooler reservoir tank assembly.

Standard capacity:

2.6 liters (2.7 US qts, 2.2 Imp. qts)


NOTICE:

Never use water as a substitute for coolant.


HINT:

TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).



iii.

Tighten the bleeder plug of the intercooler cooling radiator assembly.


iv.

Connect the GTS to the DLC3.


v.

Turn the engine switch on (IG).


vi.

Enter the following menus: Powertrain / Engine / Active Test / Control the Intercooler Water Pump.


vii.

While adding coolant so that the coolant level is kept near the F line in the intercooler reservoir assembly, activate the electric water pump assembly for approximately 1 minute and then stop pump operation for 1 minute. At that time, check that air bubbles are discharged to the intercooler reservoir assembly.

Standard:

Repeat this operation approximately 3 times until the sound of the electric water pump assembly gets smaller and no more bubbles are visible from the intercooler reservoir assembly or the coolant level in the intercooler reservoir assembly stabilizes. When this condition is reached, this indicates that air is completely bled from the coolant system.


HINT:

If the intercooler reservoir assembly is filled excessively with coolant, coolant may spill out when the electric water pump assembly is stopped.



viii.
A421190C02
1.719,1.146 2.031,1.302 0.313,0.156 10 false .
V100135

F Line


When air is completely bled, add coolant up to the F line in the intercooler reservoir assembly, and install the reservoir cap (for Intercooler).



b.

When not using the GTS:

i.
A421189C02
1.76,1.125 1.917,1.448 1.917,1.448 2.146,1.448 true 2.198,1.375 2.51,1.531 0.313,0.156 10 true *a
*a Bleeder Plug


Loosen the bleeder plug of the intercooler cooling radiator assembly.


ii.

Slowly pour coolant into the intercooler reservoir tank assembly.

Standard capacity:

2.6 liters (2.7 US qts, 2.2 Imp. qts)


NOTICE:

Never use water as a substitute for coolant.


HINT:

TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).



iii.

Tighten the bleeder plug of the intercooler cooling radiator assembly.


iv.

Install the reservoir cap (for Intercooler). [*1]


v.

Start the engine. [*2]


vi.

In order to operate the electric water pump assembly, maintain the engine speed at 2000 rpm or higher with the shift lever in N or P for 1 minute and then stop operation for 1 minute. Repeat this operation approximately 3 times until the sound of the electric water pump assembly gets smaller and no more bubbles are visible from the intercooler reservoir assembly or the coolant level in the intercooler reservoir assembly stabilizes. [*3]

CAUTION:
·

Be careful as the radiator hoses are hot.

·

Keep your hands away from the cooling fan.



NOTICE:
·

Make sure that the coolant level in the intercooler reservoir assembly does not drop below the L line when the engine speed is 2000 rpm or higher.

·

Immediately after starting the engine, if the intercooler reservoir assembly runs out of coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) pour in coolant until it reaches the F line.




vii.

Stop the engine and wait until the coolant cools down to ambient temperature. [*4]


viii.
A421190C02
1.719,1.146 2.031,1.302 0.313,0.156 10 false .
V100135

F Line


Check that the coolant level is between the F and L line. [*5]

If the coolant level is lower than the L line, pour coolant of the specified concentration into the intercooler reservoir assembly until it reaches the F line, and repeat the procedure from steps [*1] to [*5].

If the coolant level is above the F line, drain coolant so that the coolant level is between the F and L line.