Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › MANIFOLD ABSOLUTE PRESSURE SENSOR › 2018.06–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260469 MANIFOLD ABSOLUTE PRESSURE SENSOR G

1GD-FTV ENGINE CONTROL  MANIFOLD ABSOLUTE PRESSURE SENSOR  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 89421C 1.INSPECT DIESEL TURBO PRESSURE SENSOR

a.

Inspect the power source voltage.

i.

Disconnect the diesel turbo pressure sensor connector.


ii.

Turn the engine switch on (IG).


iii.
A200310C13
1.531,1.198 1.219,1.583 1.219,1.583 1.115,1.583 false 1.948,1.198 2.25,1.594 2.25,1.594 2.354,1.594 false 0.865,1.5 1.094,1.688 0.229,0.188 10 false E2 2.396,1.5 2.625,1.688 0.229,0.188 10 false VC 0.073,0.042 0.281,0.229 0.208,0.188 10 false *a
*a Front view of wire harness connector
(to Diesel Turbo Pressure Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
3 (VC) - 1 (E2) Engine switch on (IG) 4.75 to 5.25 V



iv.

Turn the engine switch off.


v.

Connect the diesel turbo pressure sensor connector.


vi.

Clear the DTCs.



b.

Inspect the diesel turbo pressure sensor.

i.

Connect the GTS to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / Atmosphere Pressure and MAP.


v.

Disconnect the vacuum hose from the diesel turbo pressure sensor.


vi.

Using SST, apply pressure to the diesel turbo pressure sensor.

A424430C01
2.958,0.99 3.073,0.729 3.073,0.729 3.24,0.729 false 2.76,2.573 2.875,2.313 2.875,2.313 3.042,2.313 false 6.313,2.552 6.427,2.292 6.427,2.292 6.594,2.292 false 6.448,0.948 6.563,0.688 6.563,0.688 6.729,0.688 false 0.115,0.083 0.427,0.24 0.313,0.156 10 false *A 4,0.073 4.313,0.229 0.313,0.156 10 false *B 3.104,2.229 3.344,2.427 0.24,0.198 10 true *a 3.292,0.646 3.646,0.833 0.354,0.188 10 false SST 6.656,2.208 6.896,2.406 0.24,0.198 10 true *a 6.781,0.615 7.135,0.802 0.354,0.188 10 false SST
*A w/o Urea SCR System *B w/ Urea SCR System
*a Vacuum Pump - -


SST
09992-00242  


vii.

Using a vacuum pump, apply vacuum to the diesel turbo pressure sensor.


viii.

Read the value.

OK:
Condition MAP Value
No pressure applied Same as atmospheric pressure
Pressure applied Indicates pressure
Vacuum applied Indicates vacuum


If the result is not as specified, replace the diesel turbo pressure sensor or ECM.