The Intake Air Temperature Sensor (for Intake Air Connector) detects the intake air temperature after the intake air passes through the intercooler. A built-in thermistor in the sensor changes its resistance value according to the intake air temperature. The lower the intake air temperature, the higher the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (See Fig. 1).
The sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the sensor from terminal THIA via resistor R. Resistor R and the sensor are connected in series. When the resistance value of the sensor changes in accordance with changes in the intake air temperature, the potential at terminal THIA also changes. Based on this signal, the ECM corrects the fuel injection volume to improve driveability with a cold engine.
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Engine switch on (IG) for 1 second or more | Short in the intake air temperature sensor (for intake air connector) circuit for 0.5 seconds.
(1 trip detection logic). |
·
Short in intake air temperature sensor (for intake air connector) circuit ·
Intake air temperature sensor (for intake air connector) ·
ECM |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Engine switch on (IG) for 1 second or more | Open in the intake air temperature sensor (for intake air connector) circuit for 0.5 seconds.
(1 trip detection logic) |
·
Open in intake air temperature sensor (for intake air connector) circuit ·
Intake air temperature sensor (for intake air connector) ·
ECM |
| DTC No. | Data List |
|---|---|
| P007C
P007D |
Intake Air Temp (Turbo) |
If DTC P007C or P007D is stored, the following symptoms may appear:
Misfire
Combustion noise
Black smoke
White smoke
Lack of power
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).
Read the value.
Same as air temperature near intake manifold
| Result | Proceed to |
|---|---|
| -40°C (-40°F) | A |
| 140°C (284°F) or higher | B |
| OK (same as air temperature near intake manifold) | C |
If there is an open circuit, the GTS indicates -40°C (-40°F).
If there is a short circuit, the GTS indicates 140°C (284°F) or higher.
A
B
C
| *1 | Intake Air Temperature Sensor (for intake air connector) |
| *2 | ECM |
| *a | Front view of wire harness connector
(to Intake Air Temperature Sensor (for intake air connector)) |
Disconnect the intake air temperature sensor (for intake air connector) connector.
Connect terminals 1 and 2 of the intake air temperature sensor (for intake air connector) wire harness side connector.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).
Read the value.
140°C (284°F) or higher
Reconnect the intake air temperature sensor (for intake air connector) connector.
OK
NG
Replace the intake air temperature sensor (for intake air connector).
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>REMOVAL
NEXT
Disconnect the intake air temperature sensor (for intake air connector) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C176-2 - C150-35 (THIA) | Always | Below 1 Ω |
| C176-1 - C150-27 (ETHI) | Always | Below 1 Ω |
Reconnect the intake air temperature sensor (for intake air connector) connector.
Reconnect the ECM connector.
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
NEXT
| *1 | Intake Air Temperature Sensor (for Intake Air Connector) |
| *2 | ECM |
Disconnect the intake air temperature sensor (for intake air connector) connector.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).
Read the value.
-40°C (-40°F)
Reconnect the intake air temperature sensor (for intake air connector) connector.
OK
NG
Replace the intake air temperature sensor (for intake air connector).
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>REMOVAL
NEXT
Disconnect the intake air temperature sensor (for intake air connector) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C176-2 or C150-27 (THIA) - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the intake air temperature sensor (for intake air connector) connector.
Reconnect the ECM connector.
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
NEXT
Repair or replace the harness or connector.
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>DTC CHECK / CLEAR
Turn the engine switch off for 30 seconds or more.
Turn the engine switch on (IG) for 1 second or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
NEXT