Home › Engine / Hybrid System › 2TR-FE (ENGINE MECHANICAL) › DRIVE BELT › from 2018.06
RM27T0E _51 Engine / Hybrid System _053663 2TR-FE ENGINE MECHANICAL _0260499 DRIVE BELT A

2TR-FE ENGINE MECHANICAL  DRIVE BELT  INSTALLATION  


PROCEDURE

Hide 16603B 1.INSTALL TENSIONER PULLEY

NOTICE:

Perform the following procedure when it is necessary to replace the tensioner pulley.


HINT:

The tensioner pulley service kit consists of a bolt, dust seal and tensioner pulley.


a.
A415340E01
0.438,1.708 0.594,1.406 0.594,1.406 0.792,1.406 false 1.635,1.365 1.854,0.948 1.854,0.948 2.052,0.948 false 2.604,1.073 2.823,0.656 2.823,0.656 3.021,0.656 false 0.823,1.313 1.042,1.49 0.219,0.177 10 false *1 2.083,0.865 2.292,1.073 0.208,0.208 10 false *2 3.052,0.563 3.25,0.75 0.198,0.188 10 false *3

Install the dust seal and bolt to the tensioner pulley as shown in the illustration.

Text in Illustration
*1 Bolt
*2 Dust Seal
*3 Tensioner Pulley
V100135

Front

NOTICE:
·

The dust seal must be oriented correctly when installed, If the dust seal is installed incorrectly, the bearing may be damaged.

·

Do not touch the seal surface of the bearing.



HINT:

Be sure to use the bolt from the service kit.



b.

Tighten the bolt by hand until the flange of the bolt contacts the dust seal and the tensioner pulley is fixed in place.

NOTICE:

Do not use any tools.



c.

Tighten the bolt.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


Hide 16361A 2.INSTALL FAN AND GENERATOR V BELT

a.
A348629E03
0.885,2.865 0.479,2.865 true 1.323,3.365 0.948,3.781 0.948,3.781 0.781,3.781 true 1.615,4.24 1.615,3.833 true 2.354,4.188 2.177,4.188 2.177,4.188 2.01,3.552 true 2.813,3.656 2.406,3.656 true 2.573,3.156 2.406,3.156 2.406,3.156 1.938,3.208 true 2.771,2.469 2.625,2.469 2.625,2.469 2.396,2.76 true 1.844,2.323 1.698,2.323 1.698,2.323 1.583,2.906 true 0.281,2.771 0.5,2.969 0.219,0.198 10 false *1 2.844,3.573 3.063,3.771 0.219,0.198 10 false *8 2.396,4.094 2.625,4.313 0.229,0.219 10 false *7 1.542,4.25 1.76,4.448 0.219,0.198 10 false *6 0.594,3.688 0.781,3.896 0.188,0.208 10 false *5 2.615,3.063 2.823,3.26 0.208,0.198 10 false *4 2.813,2.375 3.021,2.563 0.208,0.188 10 false *3 1.885,2.229 2.094,2.438 0.208,0.208 10 false *2

Install the fan and generator V belt to all the pulleys except the tensioner pulley.

Text in Illustration
*1 Generator Assembly
*2 Idler Pulley Sub-assembly
*3 Vane Pump Assembly
*4 Fan Pulley
*5 Tensioner Pulley
*6 Crankshaft Pulley
*7 No. 1 Idler Pulley Sub-assembly
*8 Cooler Compressor Assembly


b.

Use the hexagonal part indicated by the arrow in the illustration to move the tensioner pulley downward and install the fan and generator V belt to the tensioner pulley.

NOTICE:
·

The backside of the fan and generator V belt should face the tensioner pulley.

·

Check that the fan and generator V belt is properly set on each pulley.