Home › Drivetrain › A750F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION FLUID › 2019.08–2020.08
RM27T0E _52 Drivetrain _053697 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0260754 AUTOMATIC TRANSMISSION FLUID N

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION FLUID  ADJUSTMENT  


CAUTION / NOTICE / HINT

C210202E01
1.645,3.18 4.279,3.363 2.634,0.183 12 FLUID TEMPERATURE CHECK 0.406,5.189 2.210,5.383 1.803,0.194 12 FLUID LEVEL CHECK 0.173,0.06 2.255,0.400 2.083,0.340 12 Fluid Filling Procedure: 0.166,0.419 1.942,0.827 1.776,0.409 12 TRANSMISSION FILL (When necessary) 0.155,1.107 2.961,1.285 2.806,0.178 10 Add fluid to the oil pan to the specified level. 4.16,0.746 6.830,1.103 2.670,0.357 10 Add the correct amount of fluid specified for the operation that was performed. 0.239,2.234 1.635,2.876 1.395,0.642 10 Add fluid until fluid comes out of the overflow plug hole. 0.131,7.008 2.266,7.404 2.135,0.396 10 Keep the overflow plug open until only drops of fluid come out. 0.413,5.539 2.881,6.016 2.468,0.477 10 Drain excess fluid at the specified fluid temperature. 4.322,5.445 6.801,5.781 2.479,0.336 10 If no fluid comes out, add fluid until fluid comes out of the overflow plug hole. 1.613,3.53 7.061,3.947 5.447,0.417 10 Start the engine to circulate the fluid. Enter fluid temperature detection mode and engine idle speed control mode, and adjust the fluid temperature to the specified value. 6.242,1.586 6.887,2.107 0.644,0.521 10 Specified Amount of Fluid 2.03,2.445 3.348,2.823 1.318,0.378 10 No. 1 Transmission Oil Filler Tube 1.78,2.016 2.63,2.369 2.63,2.369 2.63,2.414 false 5.244,1.944 5.84,2.186 5.84,2.186 5.84,2.29 false 5.328,2.331 6.307,2.525 0.979,0.194 10 Overflow Plug 3.977,5.35 7.107,7.643 3.13,2.293

NOTICE:
·

This transmission requires Toyota Genuine ATF WS.

·

After servicing the transmission, you must follow the ATF adjustment procedure.

·

Maintain the vehicle in a horizontal position while adjusting the fluid level.



PROCEDURE

Hide 1.BEFORE FILLING TRANSMISSION

·

When you have replaced the entire automatic transmission assembly, automatic transmission oil pan sub-assembly, drain plug, transmission valve body assembly and/or torque converter assembly, proceed to the "Transmission Fill" procedures.

·

When you have replaced the transmission hose and/or output shaft oil seal, proceed to the "Fluid Temperature Check" procedures.


Hide 2. TRANSMISSION FILL

a.
C269514C05
1.521,3.74 1.406,4.302 1.406,4.302 1.25,4.302 true 0.969,1.531 0.969,0.198 0.969,0.198 1.219,0.198 true 1.156,1.646 1.406,0.521 1.406,0.521 1.667,0.521 true 1.719,0.458 2.031,0.615 0.313,0.156 10 false *2 1.271,0.104 1.583,0.26 0.313,0.156 10 false *3 1.063,4.219 1.375,4.375 0.313,0.156 10 false *1
*1 Overflow Plug
*2 Refill Plug
*3 O-ring


Using a 5 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transmission assembly.


b.

Remove the refill plug and O-ring from the automatic transmission assembly.


c.
C358120C01
0.427,1.385 0.646,1.385 0.646,1.385 0.844,0.823 true 2.563,1.406 2.344,1.406 2.344,1.406 1.792,0.865 true 2.594,1.313 2.906,1.469 0.313,0.156 10 false *1 0.26,1.281 0.573,1.438 0.313,0.156 10 false *a
*1 Overflow Tube
*a Specified Fluid Level


Fill the transmission through the refill hole until fluid begins to trickle out of the overflow tube.


d.

Using a 5 mm hexagon socket wrench, temporarily install the overflow plug and gasket to the automatic transmission assembly.

HINT:

Reuse the old gasket as the overflow plug will be removed again.



e.

Fill the transmission with the amount of fluid listed in the table below.

Reference Capacity:
Repair Fill Amount
Transmission pan and drain plug removal 1.7 liters (1.8 US qts, 1.5 Imp. qts)
Transmission valve body removal 4.3 liters (4.5 US qts, 3.8 Imp. qts)
Torque converter removal 5.4 liters (5.7 US qts, 4.8 Imp. qts)



f.

Install the refill plug.

HINT:

If you cannot fill the listed amount of fluid, perform the following:


i.

Start the engine and idle it.

NOTICE:

Check that electrical systems such as the air conditioning system, audio system and lighting system are off.



ii.

Move the shift lever through the entire gear range to circulate the fluid.


iii.

Wait for 30 seconds with the engine idling.


iv.

Stop the engine.


v.

Remove the refill plug.


vi.

Fill the transmission with the remaining fluid until the amount in the table has been filled.


vii.

Install the refill plug.



Hide 3. FLUID TEMPERATURE CHECK

NOTICE:

The ATF temperature can be confirmed by using the GTS.


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Enter the following menus: Powertrain / ECT / Data List / A/T Oil Temperature 1.


e.

Check the ATF temperature.

NOTICE:

If the ATF temperature is higher than 45°C (113°F), turn the ignition switch off and wait until the fluid temperature drops to below 40°C (104°F).



Hide 4. FLUID LEVEL CHECK

NOTICE:
·

It is necessary to change to temperature detection mode in order to idle the vehicle appropriately.

·

The ATF temperature must be between 40 and 45°C (104 and 113°F) to accurately check the fluid level.



a.

When using the GTS:

i.

Enter the following menus: Powertrain / ECT / Active Test / Connect the TC and TE1.


ii.

Depress and hold the brake pedal.


iii.

Start the engine and idle it.

NOTICE:

Check that electrical systems such as the air conditioning system, audio system and lighting system are off.



iv.

Slowly move the shift lever from P to S, and then change the gear from 1st to 5th. Then return the shift lever to P.

HINT:

Slowly move the shift lever to circulate the fluid through each part of the transmission.



v.
C380095C01
0.031,0.031 0.313,0.281 0.281,0.25 10 true *A 0.031,2.302 0.302,2.531 0.271,0.229 10 true *B
*A w/o Multi-Information Display
*B w/ Multi-Information Display


Move the shift lever to D, and quickly move it back and forth between N and D (once within 1.5 seconds) for at least 6 seconds. This will activate the fluid temperature detection mode.


vi.

Check that the D shift indicator comes on for 2 seconds.

HINT:
·

When fluid temperature detection mode is activated, the D shift indicator on the combination meter comes on for 2 seconds.

·

If the D shift indicator does not come on for 2 seconds, return to the first step and perform the procedure again.




vii.

Move the shift lever from N to P.


viii.

Release the brake pedal.


ix.

Select the Active Test item: Connect the TC and TE1 / OFF.

NOTICE:

Be sure that terminals TC and TE1 are not connected. If the terminals are connected, the automatic transmission fluid level cannot be precisely adjusted due to fluctuations in engine speed.


HINT:
·

Disconnecting terminals TC and TE1 activates engine idle speed control mode.

·

Even after terminals TC and TE1 are disconnected, automatic transmission fluid temperature detection mode will be active until the ignition switch is turned off.





b.

When not using the GTS:

NOTICE:

Make sure to switch to fluid temperature detection mode within 60 seconds after starting the engine.


i.

Depress and hold the brake pedal.


ii.

Start the engine and idle it.

NOTICE:

Check that electrical systems such as the air conditioning system, audio system and lighting system are off.



iii.

Slowly move the shift lever from P to S, and then change the gear from 1st to 5th. Then return the shift lever to P.

HINT:

Slowly move the shift lever to circulate the fluid through each part of the transmission.



iv.
C380095C01
0.031,0.031 0.313,0.281 0.281,0.25 10 true *A 0.031,2.302 0.302,2.531 0.271,0.229 10 true *B
*A w/o Multi-Information Display
*B w/ Multi-Information Display


Move the shift lever to D, and quickly move it back and forth between N and D (once within 1.5 seconds) for at least 12 seconds. This will activate the fluid temperature detection mode.


v.

Check that the D shift indicator comes on for 2 seconds.

HINT:
·

When fluid temperature detection mode is activated, the D shift indicator on the combination meter comes on for 2 seconds.

·

If the D shift indicator does not come on for 2 seconds, return to the first step and perform the procedure again.

·

Fluid temperature detection mode will be active until the ignition switch is turned off.




vi.

Move the shift lever from N to P.


vii.

Release the brake pedal.



c.

Allow the engine to idle until the fluid temperature reaches 40 to 45°C (104 to 113°F).

HINT:

The indicator [D] will come on again when the fluid temperature reaches 40°C (104°F) and will blink if it is higher than 45°C (113°F).


Indicator [D] Indication of ATF Temperature
Below 40°C (104°F) 40 to 45°C (104 to 113°F) Higher than 45°C (113°F)
Turns off Turns on Blinking


d.
C358120C01
0.427,1.385 0.646,1.385 0.646,1.385 0.844,0.823 true 2.563,1.406 2.344,1.406 2.344,1.406 1.792,0.865 true 2.594,1.313 2.906,1.469 0.313,0.156 10 false *1 0.26,1.281 0.573,1.438 0.313,0.156 10 false *a
*1 Overflow Tube
*a Specified Fluid Level


Remove the overflow plug and gasket with the engine idling.


e.

Wait until the overflow slows to a trickle.

NOTICE:

If the fluid does not overflow, perform the following:


i.

Remove the refill plug and gasket.


ii.

Refill the transmission through the refill hole until fluid begins to trickle out of the overflow tube.


iii.

Wait until the overflow slows to a trickle.


iv.

Install a new O-ring and the refill plug to the automatic transmission assembly.

Torque:
37 N*m (379 kgf*cm, 27 ft.*lbf)



f.

Using a 5 mm hexagon socket wrench, install a new gasket and the overflow plug to the automatic transmission assembly.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


g.

Install a new O-ring and the refill plug to the automatic transmission assembly.

Torque:
37 N*m (379 kgf*cm, 27 ft.*lbf)


Hide 5. COMPLETE

a.

Turn the ignition switch off.


b.

When using the GTS:

Disconnect the GTS from the DLC3.


c.

Inspect for automatic transmission fluid leaks.


Hide 6. ATF THERMAL DEGRADATION ESTIMATE RESET

HINT:

Approximately 50% or more of the automatic transmission fluid has been replaced during a repair of the transmission or a similar operation.

Click hereDrivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 1KD-FTV)>INITIALIZATION