Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › ROOF RACK › from 2020.08
RM27T0E _59 Vehicle Exterior _053749 EXTERIOR PANELS / TRIM _0261321 ROOF RACK A

EXTERIOR PANELS / TRIM  ROOF RACK  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 63437A 1.INSTALL NO. 2 ROOF CARRIER SEAL (for Type A)

HINT:

When installing the No. 2 roof carrier seal, heat the roof rack assembly LH surface using a heat light.


Standard:
Item Temperature
Roof Rack Assembly LH 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the roof rack assembly LH excessively.


a.

Clean the roof rack assembly LH surface.

i.

Using a heat light, heat the roof rack assembly LH surface.


ii.

Remove the double-sided tape from the roof rack assembly LH surface.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new No. 2 roof carrier seal.

i.

Remove the peeling paper from the face of a new No. 2 roof carrier seal.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



ii.

Install the 4 No. 2 roof carrier seals.

HINT:

Press the No. 2 roof carrier seal firmly to install it.




Hide 75564B 2.INSTALL NO. 2 ROOF DRIP SIDE FINISH MOULDING RETAINER (for Type A)

a.

Install a new No. 2 roof drip side finish moulding retainer with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 63470B 3.INSTALL ROOF RACK ASSEMBLY LH (for Type A)

a.

Clean the threads of the bolts with non-residue solvent (when reusing the bolts).


b.

Apply adhesive to the threads of the bolts (when reusing the bolts).

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Install the roof rack assembly LH with the 5 bolts.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


Hide 63492 4.INSTALL FRONT ROOF RACK LEG COVER LH (for Type A)

a.

Attach the 2 guides and 4 claws to install the front roof rack leg cover LH.


Hide 63494 5.INSTALL REAR ROOF RACK LEG COVER LH (for Type A)

a.

Attach the 2 guides and 4 claws to install the rear roof rack leg cover LH.


Hide 63496 6.INSTALL CENTER ROOF RACK LEG COVER LH (for Type A)

a.

Attach the 2 claws to install the center roof rack leg cover LH.


Hide 63437A 7.INSTALL NO. 2 ROOF CARRIER SEAL (for Type B)

HINT:

When installing the No. 2 roof carrier seal, heat the roof rack assembly LH surface using a heat light.


Standard:
Item Temperature
Roof Rack Assembly LH 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the roof rack assembly LH excessively.


a.

Clean the roof rack assembly LH surface.

i.

Using a heat light, heat the roof rack assembly LH surface.


ii.

Remove the double-sided tape from the roof rack assembly LH surface.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new No. 2 roof carrier seal.

i.

Remove the peeling paper from the face of a new No. 2 roof carrier seal.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



ii.

Install the 6 No. 2 roof carrier seals.

HINT:

Press the No. 2 roof carrier seal firmly to install it.




Hide 63470B 8.INSTALL ROOF RACK ASSEMBLY LH (for Type B)

a.

Clean the threads of the bolts with non-residue solvent (when reusing the bolts).


b.

Apply adhesive to the threads of the bolts (when reusing the bolts).

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Install the roof rack assembly LH with the 6 bolts.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


Hide 75631K 9.INSTALL NO. 1 ROOF SIDE GARNISH LID LH (for Type B)

HINT:

Use the same procedure for all No. 1 roof side garnish lids LH.


a.

Attach the 2 guides and 2 claws to install the No. 1 roof side garnish lid LH.