Home › Drivetrain › CLUTCH › CLUTCH PEDAL (for LHD) › from 2020.08
RM27T0E _52 Drivetrain _053699 CLUTCH _0260792 CLUTCH PEDAL(for LHD) N

CLUTCH  CLUTCH PEDAL(for LHD)  ADJUSTMENT  


PROCEDURE

Hide 1.INSPECT AND ADJUST CLUTCH PEDAL ASSEMBLY

a.

Fold back the floor carpet.


b.
C358137E01
2.667,1.5 2.5,1.5 2.5,1.5 2.083,1.01 true 0.583,2.833 0.75,2.833 0.75,2.833 1.667,1.667 true 2.688,1.417 3,1.615 0.313,0.198 10 false *a 0.417,2.75 0.729,2.948 0.313,0.198 10 false *b 2.333,4.042 2.646,4.24 0.313,0.198 10 false *c

Check that the pedal height is correct.

Pedal height from floor:
Engine Specified Condition
2TR-FE
5L-E
160.4 to 170.4 mm (6.32 to 6.70 in.)
1GR-FE
1GD-FTV
172.9 to 182.9 mm (6.81 to 7.20 in.)


Text in Illustration
*a Pedal Height Adjustment Point
*b Push Rod Play and Free Play Adjustment Point
*c Pedal Height


c.

Adjust the pedal height.

i.

w/ Cruise Control:

Loosen the lock nut and turn the clutch switch until the height is correct. Tighten the lock nut.

Torque:
16 N*m (160 kgf*cm, 12 ft.*lbf)


ii.

w/o Cruise Control:

Loosen the lock nut and turn the clutch pedal stopper bolt until the height is correct. Tighten the lock nut.

Torque:
26 N*m (260 kgf*cm, 19 ft.*lbf)



d.
D031462E19
1.938,1.854 1.25,1.854 false 1.875,1.594 1.875,1.698 false 1.865,1.698 2.625,1.698 false 2.677,1.604 2.927,1.771 0.25,0.167 10 false *b 1,1.76 1.229,1.938 0.229,0.177 10 false *a

Check the pedal free play and push rod play.

Text in Illustration
*a Pedal Free Play
*b Push Rod Play

HINT:

Pay close attention to the change in resistance to distinguish between pedal free play and push rod play while performing the inspection.


i.

Depress the clutch pedal until resistance is felt.


ii.

Measure the distance between the pedal's released position and the position in the previous step.

Pedal free play:

5.0 to 15.0 mm (0.197 to 0.591 in.)



iii.

Release the pedal. Using your finger, gently press the pedal until resistance increases slightly.


iv.

Measure the distance between the pedal's released position and the position in the previous step.

Push rod play at pedal top:

1.0 to 5.0 mm (0.0394 to 0.197 in.)




e.

Adjust the pedal free play and push rod play.

HINT:

The push rod play can be adjusted by changing the length of the push rod. Pedal free play changes together with push rod play.


i.

Loosen the lock nut and turn the push rod until the pedal free play and push rod play are within the specified ranges.

NOTICE:

If pedal free play and push rod play are not within the standard range even after adjustment, inspect the related parts.



ii.

Tighten the lock nut.

Torque:
12 N*m (120 kgf*cm, 9 ft.*lbf)


iii.

After adjusting the pedal free play and push rod play, check the pedal height.



f.
C358138E01
1.281,1.542 0.667,0.75 0.667,0.75 0.5,0.75 true 1.552,1.594 2.167,1.083 2.167,1.083 2.333,1.083 true 0.333,0.667 0.646,0.865 0.313,0.198 10 false *a 2.354,1 2.667,1.198 0.313,0.198 10 false *b 1.313,1 1.625,1.198 0.313,0.198 10 false *C

Check the clutch release point.

Text in Illustration
*a Full Stroke End Position
*b Release Position
*c 25 mm or more

i.

Pull the parking brake lever and use wheel chocks to stabilize the vehicle.


ii.

Start the engine and run it at idle.


iii.

Without depressing the clutch pedal, slowly move the shift lever to R until the gears contact.


iv.

Gently depress the clutch pedal and measure the stroke distance from the point that the gear noise stops (release point) up to the full stroke end position.

Standard distance:

25 mm (0.984 in.) or more


If the result is not as specified, perform the following procedures.

·

Check pedal height.


·

Check push rod play and pedal free play.


·

Bleed air from clutch line.


·

Check clutch cover and disc.