Home › Drivetrain › VF4BM (TRANSFER / 4WD / AWD) › TRANSFER ASSEMBLY › from 2020.08
RM27T0E _52 Drivetrain _053703 VF4BM TRANSFER / 4WD / AWD _0260842 TRANSFER ASSEMBLY A

VF4BM TRANSFER / 4WD / AWD  TRANSFER ASSEMBLY  REASSEMBLY  


PROCEDURE

Hide 36273 1.INSTALL TRANSFER LOW PLANETARY RING GEAR

a.

Install the low planetary ring gear to the front transfer case.


b.
F043456

Using a screwdriver, install the snap ring.


Hide 2.INSTALL PIN

a.
F043455

Install the pin.


Hide 41331A 3.INSTALL COMPRESSION SPRING

a.

Install the spring.


Hide 36111C 4.INSTALL TRANSFER CASE PLUG

a.

Install the transfer case plug.

Torque:
19 N*m (190 kgf*cm, 14 ft.*lbf)


Hide 36231D 5.INSTALL TRANSFER OUTPUT SHAFT PLATE WASHER

a.
F043476

Install the washer.


Hide 36291A 6.INSTALL TRANSFER DRIVE SPROCKET BEARING

a.

Install the bearing.


Hide 36205 7.INSTALL TRANSFER DRIVE SPROCKET SUB-ASSEMBLY

a.

Install the transfer drive sprocket.


Hide 36255 8.INSTALL NO. 1 TRANSFER OUTPUT SHAFT SPACER

a.

Install the output shaft spacer.


Hide 36231J 9.INSTALL REAR TRANSFER OUTPUT SHAFT RADIAL BALL BEARING

a.
C357242E01
0.781,1.24 0.521,0.75 0.521,0.75 0.771,0.75 false 3.052,1.25 3.167,1.25 3.167,1.25 3.167,0.917 false 3,0.917 3.167,0.917 false 0.167,0.667 0.5,0.833 0.333,0.167 10 false SST 2.813,0.844 3.063,1.01 0.25,0.167 10 false *1

Using SST and a press, install a new bearing.

SST
09316-60011  (09316-00011, 09316-00071)

Text in Illustration
*1 Groove
V100135

Rear

NOTICE:

Install the bearing so that the bearing snap ring groove faces the rear.



Hide 36231D 10.INSTALL TRANSFER OUTPUT SHAFT PLATE WASHER

a.
F043510

Install the washer.


Hide 36231E 11.INSTALL TRANSFER OUTPUT SHAFT FRONT NEEDLE ROLLER BEARING

a.

Install the needle roller bearing.


Hide 36237 12.INSTALL TRANSFER CLUTCH HUB

a.

Install the transfer clutch hub.


Hide 41311M 13.INSTALL CENTER DIFFERENTIAL CASE

a.
F044051

Install the center differential case.


Hide 36255A 14.INSTALL TRANSFER OUTPUT SHAFT SPACER BALL

a.

Install the ball.


Hide 36256 15.INSTALL NO. 2 TRANSFER OUTPUT SHAFT SPACER

a.

Install the spacer.


b.

Using a snap ring expander, install the snap ring.


Hide 16.INSPECT DRIVE SPROCKET RADIAL CLEARANCE

F044050

a.

Using a dial indicator, measure the radial clearance of the drive sprocket.

Standard clearance:

0.01 to 0.06 mm (0.000394 to 0.0236 in.)


Maximum clearance:

0.06 mm (0.0236 in.)


If the clearance is more than the maximum, replace the drive sprocket, rear output shaft or bearing.


Hide 17.INSPECT DRIVE SPROCKET THRUST CLEARANCE

F044049

a.

Using a feeler gauge, measure the thrust clearance of the drive sprocket.

Standard clearance:

0.15 to 0.24 mm (0.00591 to 0.00944 in.)


Maximum clearance:

0.24 mm (0.00944 in.)


If the clearance is more than the maximum, replace the drive sprocket.


Hide 36210A 18.INSTALL TRANSFER INPUT SHAFT BEARING

a.
F043513E07
0.948,0.406 1.333,0.406 1.333,0.406 1.104,0.594 false 0.948,1.5 1.385,1.802 1.385,1.802 1.458,1.802 false 1.365,0.333 1.667,0.5 0.302,0.167 10 false SST 1.5,1.708 1.802,1.875 0.302,0.167 10 false SST

Using SST and a press, install a new bearing with the groove facing forward.

SST
09223-15020  
09515-30010  
09950-70010  (09951-07100)


Hide 36212D 19.INSTALL TRANSFER INPUT BEARING SHAFT SNAP RING

F043468

a.

Select a new snap ring that allows minimal axial play.

Standard Snap Ring Thickness:
Mark Specified Condition
1 1.45 to 1.50 mm (0.0571 to 0.0591 in.)
2 1.50 to 1.55 mm (0.0591 to 0.0610 in.)
3 1.55 to 1.60 mm (0.0610 to 0.0630 in.)
4 1.60 to 1.65 mm (0.0630 to 0.0650 in.)
5 1.65 to 1.70 mm (0.0650 to 0.0669 in.)



b.

Using a snap ring expander, install the snap ring.


Hide 36273 20.INSTALL TRANSFER LOW PLANETARY GEAR SPLINE PIECE

a.
F043507

Using a screwdriver, install the low planetary gear spline piece and snap ring.


Hide 36270A 21.INSTALL TRANSFER LOW PLANETARY GEAR BEARING

F043469E07
2.677,0.563 2.344,1.625 2.344,1.625 2.729,0.99 false 2.198,1.646 2.552,1.813 0.354,0.167 10 false SST

a.

Using SST and a press, press in a new low planetary gear bearing.

SST
09950-60010  (09951-00570)
09950-70010  (09951-07100)

Press in depth:

7.7 to 8.3 mm (0.304 to 0.326 in.)



Hide 36216A 22.INSTALL NO. 1 TRANSFER INPUT SHAFT SEAL RING

a.
C216962

Apply gear oil to 2 new seal rings.


b.

Install the 2 seal rings to the input shaft.

NOTICE:

When installing the seal ring, make sure not to expand it so that its inner diameter exceeds 65 mm (2.55 in.).



Hide 36270A 23.INSTALL TRANSFER LOW PLANETARY GEAR THRUST BEARING

a.
F043454

Install the bearing.

Text in Illustration
V100135

Front


Hide 36288 24.INSTALL NO. 1 TRANSFER THRUST BEARING RACE

a.

Install the thrust bearing race.


Hide 36211 25.INSTALL TRANSFER INPUT SHAFT

a.

Install the transfer input shaft.


Hide 26.INSTALL MANUAL TRANSFER PLANETARY CARRIER WASHER

a.
F043453

Install the washer.


Hide 36213A 27.INSTALL TRANSFER INPUT GEAR STOPPER BALL

a.

Install the ball.


Hide 36213 28.INSTALL TRANSFER INPUT GEAR STOPPER

a.

Install the input gear stopper.


Hide 36213B 29.INSTALL TRANSFER INPUT GEAR STOPPER SHAFT SNAP RING

a.
F043514

Select a new input gear stopper shaft snap ring that allows 0.05 to 0.15 mm (0.00197 to 0.00590 in.) of axial play.

Standard Snap Ring Thickness:
Specified Condition
2.10 to 2.15 mm (0.0827 to 0.0846 in.)
2.15 to 2.20 mm (0.0846 to 0.0866 in.)
2.20 to 2.25 mm (0.0866 to 0.0886 in.)
2.25 to 2.30 mm (0.0886 to 0.0906 in.)
2.30 to 2.35 mm (0.0906 to 0.0925 in.)
2.35 to 2.40 mm (0.0925 to 0.0945 in.)
2.40 to 2.45 mm (0.0945 to 0.0965 in.)
2.45 to 2.50 mm (0.0965 to 0.0984 in.)
2.50 to 2.55 mm (0.0984 to 0.100 in.)
2.55 to 2.60 mm (0.100 to 0.102 in.)
2.60 to 2.65 mm (0.102 to 0.104 in.)
2.65 to 2.70 mm (0.104 to 0.106 in.)
2.70 to 2.75 mm (0.106 to 0.108 in.)
2.75 to 2.80 mm (0.108 to 0.110 in.)
2.80 to 2.85 mm (0.110 to 0.112 in.)
2.85 to 2.90 mm (0.112 to 0.114 in.)
2.90 to 2.95 mm (0.114 to 0.116 in.)
2.95 to 3.00 mm (0.116 to 0.118 in.)
3.00 to 3.05 mm (0.118 to 0.120 in.)



b.
Q007289

Using a snap ring expander, install the snap ring.


Hide 30.INSTALL LOW PLANETARY GEAR ASSEMBLY WITH TRANSFER INPUT SHAFT SUB-ASSEMBLY

a.
F043450

Install the low planetary gear together with the input shaft.


b.
F043449

Using a snap ring expander, install the shaft snap ring.


Hide 36227 31.INSTALL TRANSFER OIL PUMP GEAR

a.
F043448

Install the transfer oil pump gear.


Hide 36104J 32.INSTALL TRANSFER OIL PUMP BODY O-RING

a.
U116668

Coat a new O-ring with gear oil and install it to the oil pump body.


Hide 36106 33.INSTALL TRANSFER OIL PUMP BODY SUB-ASSEMBLY

a.
C357243

Install the oil pump body with the 3 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 33449D 34.INSTALL TRANSFER CASE MAGNET

Hide 36104H 35.INSTALL TRANSFER OIL SEPARATOR SUB-ASSEMBLY

a.
F043446

Install the oil separator with the 3 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 36114B 36.INSTALL FILLER PLUG

a.

Install a new gasket and the filler plug.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 36114B 37.INSTALL DRAIN PLUG

a.

Install a new gasket and the drain plug.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 36410J 38.INSTALL TRANSFER SHIFT ACTUATOR ASSEMBLY

a.
C314513

Install a new O-ring to the transfer shift actuator assembly.


b.
C357244

Install the transfer shift actuator assembly with the 3 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


c.

Using a screwdriver and hammer, tap on the 2 snap rings.


Hide 36212A 39.INSTALL TRANSFER INPUT GEAR RADIAL BALL BEARING

a.
C216377E01
0.713,1.036 1.091,1.233 0.377,0.197 10 SST 1.933,1.549 1.431,1.132 false 1.431,1.132 1.11,1.132 false

Using SST and a press, install a new input gear radial ball bearing.

SST
09316-60011  (09316-00031)


Hide 36292A 40.INSTALL TRANSFER DRIVEN SPROCKET BEARING

a.
C216378E01
0.919,2.385 1.291,2.601 0.372,0.216 10 SST 2.261,2.49 1.289,2.49 false

Using SST and a press, install a new driven sprocket bearing.

SST
09316-60011  (09316-00071)


Hide 41.INSTALL REAR OUTPUT SHAFT SUB-ASSEMBLY, FRONT DRIVE CHAIN AND DRIVEN SPROCKET SUB-ASSEMBLY

a.
F043505

Install the rear output shaft and drive sprocket to the front drive chain.


b.
F043441

Install the rear output shaft, front drive chain and driven sprocket to the rear transfer case.

HINT:

Check that the rear output shaft and driven sprocket turn without much effort.



c.

Using a snap ring expander, install the snap ring.

NOTICE:

Make sure that the snap ring is firmly installed to the groove.



Hide 41408 42.INSTALL CENTER DIFFERENTIAL LOCK FORK SUB-ASSEMBLY WITH FRONT DRIVE CLUTCH SLEEVE

a.
F043519

Install the center differential lock fork and front drive clutch sleeve.

Text in Illustration
V100135

Front

NOTICE:

Install the clutch sleeve in the correct direction.



b.

Install the bolt.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


c.

Using a screwdriver and hammer, drive in the snap ring.


Hide 43.INSTALL NO. 2 TRANSFER GEAR SHIFT FORK SUB-ASSEMBLY WITH TRANSFER HIGH AND LOW CLUTCH SLEEVE

a.
F044401

Install the No. 2 gear shift fork and high and low clutch sleeve.

Text in Illustration
V100135

Front

NOTICE:

Install the clutch sleeve in the correct direction.



b.

Install the bolt.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


Hide 36231E 44.INSTALL TRANSFER OUTPUT SHAFT FRONT NEEDLE ROLLER BEARING

a.

Install the needle roller bearing to the input shaft.


Hide 36231A 45.INSTALL TRANSFER OUTPUT SHAFT SPACER

a.

Install the transfer output shaft spacer to the input shaft.


Hide 36112 46.INSTALL REAR TRANSFER CASE

a.
F043488E15
2.125,0.729 2.479,0.375 2.479,0.375 2.625,0.375 false 2.688,0.271 2.885,0.469 0.198,0.198 10 false *1

Apply seal packing to the rear transfer case as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


Text in Illustration
*1 Seal Packing

NOTICE:

If the removed rear transfer case is reused, be sure to perform the following before reinstalling it: 1) using a knife, cut off any old seal packing on the rear transfer case contact surface, 2) clean off any remaining old seal packing from the rear transfer case contact surface, and 3) reapply seal packing to the rear transfer case.



b.
U116131

Install the clamp and rear transfer case with the 12 bolts.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

NOTICE:

Tighten the bolts of the rear transfer case within 10 minutes of applying the seal packing. The seal packing will dry very quickly.



Hide 47.INSTALL COLLAR

a.
F043432

Install the collar.


Hide 33309H 48.INSTALL TRANSFER OUTPUT SHAFT WASHER

a.

Install the 2 washers.


Hide 36105 49.INSTALL TRANSFER EXTENSION HOUSING SUB-ASSEMBLY

a.
F043489E12
2.51,1.042 2.729,0.833 2.729,0.833 2.833,0.833 false 2.875,0.719 3.042,0.917 0.167,0.198 10 false *1

Apply seal packing to the extension housing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


Text in Illustration
*1 Seal Packing

NOTICE:

If the removed extension housing is reused, be sure to perform the following before reinstalling it: 1) using a knife, cut off any old seal packing on the housing contact surface, 2) clean off any remaining old seal packing from the housing contact surface, and 3) reapply seal packing to the housing.



b.

Apply adhesive to the threads of the bolts.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



c.
C357245

Install the extension housing with the 5 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:

Tighten the bolts of the extension housing within 10 minutes of applying the seal packing. The seal packing will dry very quickly.



Hide 33309D 51.INSTALL REAR TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL

a.
F043517E08
1,1.563 0.479,0.698 0.479,0.698 1.01,0.906 false 0.104,0.552 0.427,0.75 0.323,0.198 10 false SST

Using SST and a hammer, tap in a new oil seal.

SST
09950-60010  (09951-00320)
09950-70010  (09951-07100)


b.

Coat the lip of the oil seal with MP grease.


Hide 33309C 52.INSTALL REAR OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY

a.
C217384E01
2.494,2.995 2.883,3.249 0.389,0.254 10 SST 1.948,3.438 2.268,3.069 false 2.268,3.069 2.44,3.069 false

Apply gear oil to the connecting areas of the companion flange and output shaft.


b.

Install the companion flange to the output shaft.

Text in Illustration
V100135

Rear


c.

Using SST to hold the companion flange, install a new lock nut.

SST
09330-00021  

Torque:
118 N*m (1203 kgf*cm, 87 ft.*lbf)


d.
F050151E10
0.802,0.25 1,0.448 0.198,0.198 10 false *a 0.802,1.885 0.99,2.083 0.188,0.198 10 false *b

Using a chisel and hammer, stake the lock nut.

Text in Illustration
*a Correct
*b Incorrect

NOTICE:
·

Securely stake the shaft to the lock nut groove.

·

Be careful not to damage the parts around the lock nut.

·

Do not apply excessive force to the shaft.




Hide 33309D 54.INSTALL FRONT TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL

a.
F043517E09
1,1.563 0.479,0.698 0.479,0.698 1.01,0.906 false 0.104,0.552 0.427,0.75 0.323,0.198 10 false SST

Using SST and a hammer, tap in a new oil seal.

SST
09950-60010  (09951-00320)
09950-70010  (09951-07100)


b.

Coat the lip of the oil seal with MP grease.


Hide 33309C 55.INSTALL FRONT OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY

C217366E01
2.747,2.47 3.086,2.648 0.339,0.178 10 SST 2.024,3.394 2.365,2.542 false 2.365,2.542 2.652,2.542 false

a.

Apply gear oil to the connecting areas of the companion flange and driven sprocket.


b.

Install the companion flange to the driven sprocket.

Text in Illustration
V100135

Front


c.

Using SST to hold the companion flange, install a new lock nut.

SST
09330-00021  

Torque:
118 N*m (1203 kgf*cm, 87 ft.*lbf)


d.
F050151E11
0.802,0.25 1,0.448 0.198,0.198 10 false *a 0.802,1.885 0.99,2.083 0.188,0.198 10 false *b

Using a chisel and hammer, stake the lock nut.

Text in Illustration
*a Correct
*b Incorrect

NOTICE:
·

Securely stake the shaft to the lock nut groove.

·

Be careful not to damage the parts around the lock nut.

·

Do not apply excessive force to the shaft.




Hide 36128 56.INSTALL BREATHER OIL DEFLECTOR

a.

Install the oil deflector.


Hide 36102 57.INSTALL TRANSFER CASE COVER SUB-ASSEMBLY

a.
C357246

Install the case cover with the 4 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 36102F 58.INSTALL TRANSFER BEARING RETAINER OIL SEAL RH

a.
F043518E07
0.99,0.854 0.458,0.656 0.458,0.656 0.865,1.333 false 0.083,0.542 0.385,0.708 0.302,0.167 10 false SST

for AC60F, G52F, R150F:

Using SST and a hammer, drive in a new transfer bearing retainer oil seal RH until its surface is flush with the retainer upper surface.

SST
09950-60010  (09951-00590)
09950-70010  (09951-07100)


b.

for RA61F:

Using SST and a hammer, tap in 2 new transfer bearing retainer oil seals RH A and B as shown in the illustration.

SST
09950-60010  (09951-00590)
09950-70010  (09951-07100)

i.
C264672E01
0.087,0.368 0.416,0.524 0.330,0.156 10 SST 0.469,0.441 0.722,0.441 0.722,0.441 1.023,0.819 false 0.92,1.227 0.722,0.445 false 3.008,1.326 3.130,1.482 0.121,0.156 10 A 2.191,1.289 2.191,1.037 2.191,1.037 2.262,1.037 false 2.295,0.955 2.454,1.111 0.159,0.156 10 *1

for oil seal A:

Drive in depth (A):

43 to 44 mm (1.70 to 1.73 in.)


Text in Illustration
*1 Oil Seal A


ii.
C264673E01
0.087,0.347 0.378,0.502 0.291,0.156 10 SST 0.508,0.441 0.718,0.441 0.718,0.441 1.032,0.802 false 0.92,1.227 0.718,0.441 false 0.508,0.441 0.718,0.441 0.718,0.441 1.032,0.802 false 0.92,1.227 0.718,0.441 false 3.013,1.249 3.130,1.401 0.118,0.152 10 B 2.15,1.194 2.15,1.031 2.15,1.031 2.195,1.031 false 2.213,0.932 2.375,1.086 0.162,0.154 10 *1

for oil seal B:

Drive in depth (B):

53.5 to 54 mm (2.11 to 2.12 in.)


Text in Illustration
*1 Oil Seal B



c.

Coat the lip of the transfer bearing retainer oil seal RH with MP grease.


Hide 36102D 59.INSTALL TRANSFER BEARING RETAINER SUB-ASSEMBLY RH

a.

for RA61F:

Install a new O-ring to the transfer bearing retainer sub-assembly RH.

NOTICE:

Apply MP grease to the O-ring when installing the transfer onto the transmission.



b.
F043490E13
2.375,0.677 2.615,0.448 2.615,0.448 2.719,0.448 false 2.771,0.354 2.958,0.552 0.188,0.198 10 false *1

Apply seal packing to the transfer bearing retainer sub-assembly RH as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


Text in Illustration
*1 Seal Packing

NOTICE:

If the removed transfer bearing retainer sub-assembly RH is reused, be sure to perform the following before reinstalling it: 1) using a knife, cut off any old seal packing on the retainer contact surface, 2) clean off any remaining old seal packing from the retainer contact surface, and 3) reapply seal packing to the transfer bearing retainer sub-assembly RH.



c.

Apply sealant to the bolt threads.

Sealant:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



d.
C357247

Install the transfer bearing retainer sub-assembly RH with the 5 bolts.

Torque:
12 N*m (117 kgf*cm, 8 ft.*lbf)

NOTICE:

Tighten the bolts of the transfer bearing retainer sub-assembly RH within 10 minutes of applying the seal packing. The seal packing will dry very quickly.



Hide 60.INSTALL HOSE

C216295

a.

Attach the clamp and install the hose.