88625
1.INSTALL NO. 1 COOLER THERMISTOR
Insert the sensor to a location that is 1 fin to the right or left of its previous location.
If reusing the evaporator, do not insert the sensor into a location where the sensor was previously inserted.
| *A | w/o Stop and Start System | *B | w/ Stop and Start System |
| *1 | 1 Fin | - | - |
| Area | Specified Condition | Area | Specified Condition |
|---|---|---|---|
| A | 45 to 55 mm (1.77 to 2.17 in.) | B | 46.7 mm (1.84 in.) |
| C | 33.3 mm (1.31 in.) | D | 154.1 mm (6.07 in.) |
| E | 20 to 30 mm (0.787 to 1.18 in.) | F | 20 to 30 mm (0.787 to 1.18 in.) |
| G | 73.5 mm (2.89 in.) | H | 60.1 mm (2.37 in.) |
| I | 140.7 mm (5.54 in.) | J | 20 to 30 mm (0.787 to 1.18 in.) |
88501
2.INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY
Sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the hose joint.
| Refrigerant | Compressor Oil |
|---|---|
| HFC-134a (R134a) | ND-OIL 8 or equivalent |
| HFO-1234yf (R1234yf) | ND-OIL 12 or equivalent |
Install the 2 O-rings to the evaporator.
Install the evaporator.
Attach the 4 claws to install the unit case.
Install the 6 screws.
87106D
3.INSTALL DAMPER SERVO SUB-ASSEMBLY LH
Align the grooves on the damper servo sub-assembly with the protrusions on the unit and install the damper servo sub-assembly.
| *A | for Automatic Air conditioning System | - | - |
| *a | Air Conditioning Unit Side | *b | Damper Servo Side |
Install the 4 screws.
87106L
4.INSTALL DAMPER SERVO SUB-ASSEMBLY RH
Align the grooves on the damper servo sub-assembly with the protrusions on the unit and install the damper servo sub-assembly.
| *a | Air Conditioning Unit Side | *b | Damper Servo Side |
Install the 3 screws.
88515
5.INSTALL COOLER EXPANSION VALVE
Install the expansion valve.
88710H
6.INSTALL AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY
Sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the hose joint.
| Refrigerant | Compressor Oil |
|---|---|
| HFC-134a (R134a) | ND-OIL 8 or equivalent |
| HFO-1234yf (R1234yf) | ND-OIL 12 or equivalent |
Install the 2 O-rings to the air conditioner tube and accessory assembly.
Using a 4 mm hexagon wrench, install the 2 bolts.
Install new butyl tape.
Install new packing.
7.INSTALL AIR CONDITIONING HARNESS
Attach the clamps to install the harness.
Connect the connectors.
87107A
8.INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY
Install the radiator.
Install the 2 brackets with the 2 screws.
87710G
9.INSTALL QUICK HEATER ASSEMBLY (w/ PTC Heater)
88539J
10.INSTALL DRAIN COOLER HOSE
install the drain cooler hose.
88669B
11.INSTALL ASPIRATOR HOSE
Attach the 2 claws to install the aspirator hose.
55950G
12.INSTALL DEFROSTER NOZZLE ASSEMBLY
Attach the 6 claws to install the defroster nozzle assembly.
87130D
13.INSTALL BLOWER ASSEMBLY
Attach the 2 claws to install the blower unit assembly.
Install the screw.