ENGINE CONTROL SYSTEM
| *1 | ECM | *2 | Pre-stroke Control Valve |
| *3 | Fuel Supply Pump Assembly | *4 | Common Rail Assembly |
| *5 | Pressure Discharge Valve | *6 | Glow Plug Controller |
| *7 | Engine Coolant Temperature Sensor (for Intercooler) | *8 | Radiator Assembly |
| *9 | Electric Water Pump Assembly | *10 | Intake Air Temperature Sensor (for Intercooler) |
| *11 | Intercooler Assembly | *12 | Intake Air Temperature Sensor (Turbo) |
| *13 | No. 1 EGR Cooler | *14 | No. 1 Vacuum Switching Valve Assembly (for EGR Bypass Valve) |
| *15 | Mass Air Flow Meter Sub-assembly | *16 | Intake Air Temperature Sensor (Built Into Mass Air Flow Meter) |
| *17 | Injector Assembly | *18 | Camshaft Position Sensor |
| *19 | Glow Plug Assembly | *20 | Electric EGR Control Valve Assembly |
| *21 | Nozzle Vane Position Sensor | *22 | Variable Vane DC Motor |
| *23 | Crankshaft Position Sensor | *24 | Engine Coolant Temperature Sensor |
| *25 | Manifold Absolute Pressure Sensor | *26 | Diesel Throttle Body Assembly |
| *27 | Oil Pressure Switching Valve Assembly | *28 | Oil Pressure Sender Gauge Assembly |
| *29 | Exhaust Fuel Addition Injector Assembly | *30 | Exhaust Gas Temperature Sensor |
| *31 | No. 2 Exhaust Gas Temperature Sensor | *32 | Differential Pressure Sensor |
| *33 | No. 3 Exhaust Gas Temperature Sensor | *34 | No. 1 Nitrogen Oxides Sensor |
| *35 | Urea Injector Set | *36 | Urea Pump |
| *37 | Urea Pump Control ECU | *38 | Particulate Matter Sensor
(w/ Particulate matter sensor) |
| *39 | No. 4 Exhaust Gas Temperature Sensor | *40 | No. 2 Nitrogen Oxides Sensor |
| *41 | Atmospheric Pressure Sensor | *42 | Accelerator Pedal Position Sensor |
i-ART SYSTEM
In the i-ART (Intelligent Accuracy Refinement Technology) System, i-ART injectors, which are injectors that have built-in pressure sensors, are used.
By incorporating a pressure sensor into the injector, any changes in the internal pressure of the injectors can be confirmed at a point close to where fuel is injected.
The i-ART injector directly detects its internal fuel pressure and fuel temperature.
The ECM receives the pressure waveform signal from the pressure sensor and detects the fuel injection volume to perform so that the fuel injection volume matches the target.
Due to this system, the fuel injection precision even in the smallest amount has been improved and precise control of multilevel injection has been made possible. In turn, combustion is more stable and the noise made during combustion has reduced.
The i-ART injectors automatically perform learning when they are replaced. Therefore, injector compensation code registration and pilot quantity learning is not necessary. Learning is performed while the engine is running.
| *1 | Nozzle | *2 | Two-Way Valve |
| *3 | Low Suck Volume Nozzle | *4 | Nozzle Needle |
| *5 | ·
Fuel Pressure Sensor ·
Fuel Temperature Sensor |
- | - |
| *a | Injector Assembly Cross Section Diagram | - | - |
DIESEL PARTICULATE FILTER SYSTEM DESCRIPTION
Diesel Particulate Filter System comprehensively regulates engine control (consists of a catalytic system and a fuel injection system) that purifies particulate matter (PM) by diesel engines. The catalytic system purifies hydrocarbons (HC) and carbon monoxides (CO), and reduces PM with a catalytic converter with the Diesel Particulate Filter (DPF). The fuel injection system adds fuel into the exhaust port using the exhaust fuel addition injector to produce and maintain a proper catalyst temperature for PM forced regeneration.
DPF components:
| Component | Description |
|---|---|
| DOC catalytic converter | Reduces HC and CO. |
| DPF catalytic converter | Reduces PM. |
| Exhaust fuel addition injector assembly | Adds fuel into the exhaust port in order to raise catalyst temperature for PM forced regeneration. |
·
Exhaust gas temperature sensor ·
No. 2 exhaust gas temperature sensor ·
No. 3 exhaust gas temperature sensor |
Used for estimating the DPF catalytic converter temperature and adjusting fuel addition by ECM while PM forced regeneration is performed. Also detects the DPF catalytic converter temperature to prevent the catalytic converter temperature from rising too high. |
| Differential pressure sensor | Detects the volume of PM deposits and any incorrect air hose arrangement on the DPF catalytic converter. |
| No. 1 Nitrogen Oxides Sensor | Used for controlling the air-fuel ratio. By controlling the air-fuel ratio, combustion control and PM forced regeneration are properly regulated. |
Diagnostics Trouble Codes (DTCs) table for DPF:
This table indicates typical DTC combinations for each malfunction occurrence.
| Trouble Area | Malfunction | DTC No. |
|---|---|---|
| DPF catalytic converter | Deteriorated or clogged | P042000*, P200200*, P200C4B*, P200E4B*, P244A00*, P244B00*, P245800*, P246300* |
| Exhaust fuel addition injector assembly | Stuck open | P20CF00 |
| Stuck closed | P042000*, P200200*, P244A00*, P245800* | |
| Low fuel addition volume | P042000*, P200200*, P244A00*, P244B00*, P245800*, P246300 | |
| Open in exhaust fuel addition injector circuit | P042000*, P200200*, P20CB14, P244A00*, P245800* | |
| Short in exhaust fuel addition injector circuit | P042000*, P200200*, P20CB12, P20CF00, P244A00*, P245800* | |
| Open or short in exhaust fuel addition injector circuit | P042000*, P200200*, P200C4B*, P200E4B, P20CB12*, P20CB14*, P20CF00, P244A00*, P245800* | |
| Exhaust gas temperature sensor | Open in exhaust gas temperature sensor circuit | P042000*, P054411, P054415, P200200*, P200C4B*, P200E4B*, P203111, P203115, P05442A, P20312A, P242A2A, P242A11, P242A15, P244A00*, P245800* |
| Short in exhaust gas temperature sensor circuit | P042000*, P054411, P054415, P200200*, P200C4B*, P200E4B*, P203111, P203115, P05442A, P20312A, P242A2A, P242A11, P242A15, P244A00*, P245800* | |
| Exhaust gas temperature sensor | P042000*, P054411, P054415, P200200*, P200C4B*, P200E4B*, P203111, P203115, P05442A, P20312A, P242A2A, P242A11, P242A15, P244A00*, P245800* | |
| Differential pressure sensor | Open in differential pressure sensor circuit | P042000*, P200200*, P244A00*, P245211, P245215, P245800*, P246300* |
| Short in differential pressure sensor circuit | P042000*, P200200*, P244A00*, P245211, P245215, P245800*, P246300* | |
| Differential pressure sensor | P042000*, P200200*, P244A00*, P245211, P245215, P245800*, P246300* | |
| Differential pressure sensor clogged | P042000*, P200200*, P244A00*, P24521C, P245800*, P246300* | |
| Incorrect air hose arrangement of the differential pressure sensor | P042000*, P200200*, P244A00*, P24521C, P245800*, P246300* | |
| No. 1 nitrogen oxides sensor | Open or short in No. 1 nitrogen oxides sensor or heater circuit | P013013, P220011, P220012, P220512, P220514, P244B00*, P246300* |
| No. 1 nitrogen oxides sensor | P219519, P219618, P220013, P225D2A, P244B00*, P246300*, U029D87 | |
| Particulate matter sensor | Open or short in particulate matter sensor or heater circuit | P24AE12, P24AE14, P24B301 |
| Particulate matter sensor | P200200, P24AE96, P24C601, P24D000 | |
| Exhaust gas leaks | Exhaust gas leaks | P042000*, P200200*, P244A00*, P245800* |
| Fuel leaks | Fuel leaks in fuel addition injector | P042000*, P200C4B*, P200E4B*, P20CF00*, P244A00*, P244B00*, P245800*, P246300* |
| Fuel supply pump assembly | Correct fuel pressure cannot be fed to the exhaust fuel addition injector | P042000*, P200200*, P244A00*, P244B00*, P245800*, P246300* |
*: There may be no DTC output depending on the condition of the malfunction.
Diagnostics trouble code description for DPF:
| DTC No. | Description |
|---|---|
| P013013 | Open in No. 1 nitrogen oxides sensor circuit |
| P042000 | DPF catalytic converter insufficient temperature increase |
| P054411 | Open or short in exhaust gas temperature sensor circuit (B1S1) (Low output) |
| P054415 | Open or short in exhaust gas temperature sensor circuit (B1S1) (High output) |
| P05442A | Exhaust gas temperature sensor circuit range/performance (B1S1) |
| P200200 | DPF catalytic converter thermal deterioration |
| P200C4B | DPF catalytic converter abnormally high exhaust gas temperature |
| P200E4B | Catalyst system temperature too high bank 1 |
| P203111 | Open or short in exhaust gas temperature sensor circuit (B1S2) (Low output) |
| P203115 | Open or short in exhaust gas temperature sensor circuit (B1S2) (High output) |
| P20312A | Exhaust gas temperature sensor circuit range/performance (B1S2) |
| P20CB12 | Short in exhaust fuel addition injector assembly circuit (High output) |
| P20CB14 | Open in exhaust fuel addition injector assembly circuit (Low output) |
| P20CF00 | Exhaust fuel addition injector assembly stuck open |
| P219519 | No. 1 nitrogen oxides sensor stuck lean |
| P219618 | No. 1 nitrogen oxides sensor stuck rich |
| P220011 | Short in No. 1 nitrogen oxides sensor circuit (Low output) |
| P220012 | Short in No. 1 nitrogen oxides sensor circuit (High output) |
| P220013 | Open in No. 1 nitrogen oxides sensor circuit |
| P220512 | Short in No. 1 nitrogen oxides sensor heater circuit (High output) |
| P220514 | Short in No. 1 nitrogen oxides sensor heater circuit (Low output) |
| P225D2A | No. 1 nitrogen oxides sensor stuck |
| P242A2A | Exhaust gas temperature sensor circuit range / performance (B1S3) |
| P242A11 | Open or short in exhaust gas temperature sensor circuit (B1S3) (Low output) |
| P242A15 | Open or short in exhaust gas temperature sensor circuit (B1S3) (High output) |
| P244A00 | DPF catalytic converter excessive differential pressure (Low input) |
| P244B00 | DPF catalytic converter excessive differential pressure (High input) |
| P24521C | Differential pressure sensor is clogged or has incorrect air hose arrangement |
| P245211 | Open or short in differential pressure sensor circuit (Low output) |
| P245215 | Open or short in differential pressure sensor circuit (High output) |
| P245800 | Diesel particulate filter regeneration duration |
| P246300 | DPF catalytic converter soot deposition |
| U029D87 | Lost communication with No. 1 nitrogen oxides sensor missing message |
UREA SCR SYSTEM
| *A | w/ Particulate Matter Sensor | - | - |
| *1 | Urea Pump Control ECU | *2 | Urea Tank Sub-assembly |
| *3 | Urea Tank Filler Pipe Assembly | *4 | Urea Tube with Heater Assembly |
| *5 | Urea Injector Set | *6 | Front Exhaust Pipe Assembly |
| *7 | Particulate Matter Sensor | *8 | No. 4 Exhaust Gas Temperature Sensor |
| *9 | No. 2 Nitrogen Oxides Sensor | *10 | Urea Pump |
Urea SCR System:
(1) A urea SCR system is used to purify NOx in the exhaust gas. The urea SCR system injects urea solution into the exhaust gas to generate ammonia. The generated ammonia produces a chemical reaction with the NOx in the exhaust gas on the SCR catalyst, breaking it down into nitrogen and water, thereby purifying the exhaust gas.
(2) The urea SCR system is composed of a urea pump control ECU, urea tank sub-assembly, urea injector set, urea pump, No. 4 exhaust gas temperature sensor and nitrogen oxides sensor.
(3) In the urea SCR system, the urea pump control ECU controls the urea injector set and urea pump based on various signals.
Urea Pump:
(1) The urea pump has the following functions:
| Function | Outline |
|---|---|
| Pump Function | While performing feedback control according to the pressure sensor inside the urea pump, the pump raises the pressure to approximately 500 kPa, sending urea solution to the urea injector set. |
| Heating Function | The heater inside the urea pump is operated to thaw the urea solution so that exhaust gas can be purified even when the ambient temperature is low and the urea solution freezes. The heater turns on and off according to the urea solution temperature sensor inside the urea pump. |
| Filter Function | Foreign matter that enters the urea tank sub-assembly is collected by the filter inside the urea pump, preventing foreign matter from getting jammed in the urea pump and urea injector set. |
| Level Gauge Function | The fluid level position is detected by the float sensor inside the urea pump in order to detect the remaining quantity of urea solution inside the urea tank sub-assembly. |
COMMON RAIL SYSTEM DESCRIPTION
Common rail system:
The common rail system uses high-pressure fuel for improved fuel economy. This system also provides robust engine power while suppressing engine vibration and noise.
This system stores fuel in the common rail, which has been pressurized and supplied by the fuel supply pump assembly. By storing fuel at high-pressure, the common rail system can provide fuel at stable fuel injection pressures, regardless of engine speed or engine load.
The ECM provides an electric current to the solenoid valve in each injector assembly to regulate the fuel injection timing and volume. The ECM also monitors the internal fuel pressure of the common rail using the fuel pressure sensor built into each injector. The ECM causes the fuel supply pump assembly to supply the fuel necessary to obtain the target fuel pressure.
In addition, this system uses a solenoid valve inside each injector assembly to open and close the fuel passages. Therefore, both fuel injection time and fuel injection volume can be precisely regulated by the ECM.
| *1 | Common Rail Assembly | *2 | Pressure Discharge Valve |
| *3 | ECM | *4 | Crankshaft Position Sensor |
| *5 | Camshaft Position Sensor | *6 | Injector Assembly |
| *7 | Pre-stroke Control Valve | *8 | Fuel Supply Pump Assembly |
| *9 | Pressurized Fuel Filter | *10 | Exhaust Fuel Addition Injector Assembly |
| *11 | Fuel Filter Element Assembly | *12 | Fuel Tank Assembly |
|
High Pressure Fuel |
|
Return Fuel |
|
Suction Fuel |
|
Feed Pressure Fuel |
If there is a problem with a fuel return pipe, as bleeding air from the fuel system may not be able to be performed properly in certain instances, such as after replacing an injector assembly, etc., the engine startability may deteriorate.
Common rail system components:
| Component | Description |
|---|---|
| Common rail assembly | Stores high-pressure fuel produced by supply pump |
| Fuel supply pump assembly | ·
Operated by crankshaft via timing chain ·
Supplies high-pressure fuel to common rail assembly |
| Injector assembly | Injects fuel to combustion chamber based on signals from ECM |
| Fuel pressure sensor (Built into injector assembly) | Monitors internal fuel pressure of injector assembly and sends signals to ECM |
| Pressure discharge valve | Based on signals from ECM, opens valve when sudden deceleration occurs, or when engine switch is off to prevent fuel pressure from becoming too high |
| Pre-stroke control valve | Based on signals from ECM, adjusts fuel volume supplied to common rail and regulates internal fuel pressure |
Diagnostic trouble code (DTC) table for the common rail system:
This table indicates typical DTC combinations for each malfunction occurrence.
| Trouble Area | Malfunction | DTC No. |
|---|---|---|
| Injector assembly | Open or short in injector circuit | P009300*, P020112, P020114, P020212, P020214, P020312, P020314, P020412, P020414, P029D00, P02A100, P02A500, P02A900, P062D96 |
| Stuck open | P009300, P029D00, P02A100, P02A500, P02A900 | |
| Stuck closed | P030100, P030200, P030300, P030400 | |
| Communication malfunction | P167A87, P167B87, P167C87, P167D87 | |
| Internal malfunction | P168A00, P168A44, P168A46, P168B00, P168B44, P168B46, P168C00, P168C44, P168C46, P168D00, P168D44, P168D46, | |
| Fuel pressure sensor (Built into injector assembly) | Open or short in fuel pressure sensor circuit | P13A011, P13A015, P13A511, P13A515, P13AA11, P13AA15, P13B011, P13B015, P13E011, P13E015, P13E511, P13E515 |
| Characteristic abnormality of the fuel pressure sensor | P13A02A, P13A52A, P13AA2A, P13B02A | |
| Fuel temperature sensor (Built into injector assembly) | Characteristic abnormality of the fuel temperature sensor | P13C013, P13C513, P13CA13, P13D013 |
| Pressure discharge valve | Open or short in pressure discharge valve circuit | P008800*, P009300*, P122900*, P127112, P127114 |
| Stuck open | P009300 | |
| Stuck closed | P008800*, P127273 | |
| Pre-stroke control valve | Open or short in pre-stroke control valve circuit | P008800*, P062712, P062714, P122900 |
| Stuck open | P008800*, P122900 | |
| Common rail system (Fuel system) | Fuel leaks in high-pressure area | P009300 |
*: There may be no DTC output depending on the condition of the malfunction.
Diagnostic trouble code description for the common rail system:
| DTC No. | Description |
|---|---|
| P008800 | Internal fuel pressure too high (275000 kPa [2804 kgf/cm2, 39875 psi] or more) |
| P009300 | Fuel leaks in high-pressure areas |
| P020112 | Short in No. 1 injector circuit (High output) |
| P020114 | Open in No. 1 injector circuit (Low output) |
| P020212 | Short in No. 2 injector circuit (High output) |
| P020214 | Open in No. 2 injector circuit (Low output) |
| P020312 | Short in No. 3 injector circuit (High output) |
| P020314 | Open in No. 3 injector circuit (Low output) |
| P020412 | Short in No. 4 injector circuit (High output) |
| P020414 | Open in No. 4 injector circuit (Low output) |
| P029D00 | Cylinder 1 - Injector Leaking |
| P02A100 | Cylinder 2 - Injector Leaking |
| P02A500 | Cylinder 3 - Injector Leaking |
| P02A900 | Cylinder 4 - Injector Leaking |
| P030100 | Cylinder 1 misfire detected |
| P030200 | Cylinder 2 misfire detected |
| P030300 | Cylinder 3 misfire detected |
| P030400 | Cylinder 4 misfire detected |
| P062712 | Short in pre-stroke control valve circuit (High output) |
| P062714 | Open in pre-stroke control valve circuit (Low output) |
| P062D96 | ECM internal error |
| P122900 | Fuel over-feed |
| P127112 | Short in pressure discharge valve circuit (High output) |
| P127114 | Open in pressure discharge valve circuit (Low output) |
| P127273 | Pressure discharge valve stuck close |
| P13A011 | Open or short in No. 1 injector assembly (fuel pressure sensor) circuit (output voltage is too low) (Sub CPU) |
| P13A015 | Open or short in No. 1 injector assembly (fuel pressure sensor) circuit (output voltage is too high) (Sub CPU) |
| P13A511 | Open or short in No. 2 injector assembly (fuel pressure sensor) circuit (output voltage is too low) (Sub CPU) |
| P13A515 | Open or short in No. 2 injector assembly (fuel pressure sensor) circuit (output voltage is too high) (Sub CPU) |
| P13AA11 | Open or short in No. 3 injector assembly (fuel pressure sensor) circuit (output voltage is too low) (Sub CPU) |
| P13AA15 | Open or short in No. 3 injector assembly (fuel pressure sensor) circuit (output voltage is too high) (Sub CPU) |
| P13B011 | Open or short in No. 4 injector assembly (fuel pressure sensor) circuit (output voltage is too low) (Sub CPU) |
| P13B015 | Open or short in No. 4 injector assembly (fuel pressure sensor) circuit (output voltage is too high) (Sub CPU) |
| P13E011 | Open or short in No. 1 injector assembly (fuel pressure sensor) circuit (output voltage is too low) (Main CPU) |
| P13E015 | Open or short in No. 1 injector assembly (fuel pressure sensor) circuit (output voltage is too high) (Main CPU) |
| P13E511 | Open or short in No. 4 injector assembly (fuel pressure sensor) circuit (output voltage is too low) (Main CPU) |
| P13E515 | Open or short in No. 4 injector assembly (fuel pressure sensor) circuit (output voltage is too high) (Main CPU) |
| P13A02A | No. 1 injector assembly (fuel pressure sensor) circuit range/performance |
| P13A52A | No. 2 injector assembly (fuel pressure sensor) circuit range/performance |
| P13AA2A | No. 3 injector assembly (fuel pressure sensor) circuit range/performance |
| P13B02A | No. 4 injector assembly (fuel pressure sensor) circuit range/performance |
| P13C013 | No. 1 injector assembly (fuel temperature sensor) circuit range/performance |
| P13C513 | No. 2 injector assembly (fuel temperature sensor) circuit range/performance |
| P13CA13 | No. 3 injector assembly (fuel temperature sensor) circuit range/performance |
| P13D013 | No. 4 injector assembly (fuel temperature sensor) circuit range/performance |
| P167A87 | No. 1 injector assembly communication malfunction |
| P167B87 | No. 2 injector assembly communication malfunction |
| P167C87 | No. 3 injector assembly communication malfunction |
| P167D87 | No. 4 injector assembly communication malfunction |
| P168A00 | No. 1 injector assembly internal malfunction |
| P168A44 | No. 1 injector assembly internal malfunction |
| P168A46 | No. 1 injector assembly internal malfunction |
| P168B00 | No. 2 injector assembly internal malfunction |
| P168B44 | No. 2 injector assembly internal malfunction |
| P168B46 | No. 2 injector assembly internal malfunction |
| P168C00 | No. 3 injector assembly internal malfunction |
| P168C44 | No. 3 injector assembly internal malfunction |
| P168C46 | No. 3 injector assembly internal malfunction |
| P168D00 | No. 4 injector assembly internal malfunction |
| P168D44 | No. 4 injector assembly internal malfunction |
| P168D46 | No. 4 injector assembly internal malfunction |
FUEL SUPPLY PUMP OPERATION SYSTEM DESCRIPTION
When the cam rotates the roller is pushed up, and in turn the plunger is pushed upward as well. When the plunger is not pushed up by the cam, it is pushed back down by the spring.
| *1 | Pre-stroke Control Valve | *2 | Plunger |
| *3 | Spring | *4 | Shoe |
| *5 | Roller | *6 | Double Cam |
The ECM controls the timing of the pre-stroke control valve opening to regulate the fuel quantity. Consequently, the fuel pressure in the common rail is controlled to the target injection pressure.
The longer the pre-stroke control valve remains open, the quantity of pressure-fed strokes will decrease, as well as the fuel discharge quantity.
Pumping will start when the fuel pressure has become higher than the common rail pressure.
| *a | Return Fuel | - | - |
The less time the pre-stroke control valve remains open, the quantity of pressure-fed strokes will increase, as well as the fuel discharge quantity.
Pumping will start when the fuel pressure has become higher than the common rail pressure.