Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › from 2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) D

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  INITIALIZATION  


INITIALIZATION PROCEDURE FOR DIESEL THROTTLE BODY ASSEMBLY, ELECTRIC EGR CONTROL VALVE ASSEMBLY AND TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR


HINT:

When the diesel throttle body assembly, electric EGR control valve assembly or turbocharger nozzle vane control actuator is replaced, perform initialization


a.

Turn the engine switch on (IG).

NOTICE:

Do not start the engine.



b.

Turn the engine switch off and wait for 30 seconds or more.


c.

Turn the engine switch on (IG) and wait for 10 seconds or more.



CATALYST DETERIORATION LEARNING VALUE AND DPF DEPOSITION VALUE CLEAR FUNCTION


HINT:

When the exhaust manifold converter sub-assembly (DPF catalyst) is replaced, the catalyst deterioration learning value and DPF deposition value stored in the ECM must be cleared.


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the menu options in this order: Powertrain / Engine / Utility / Catalyst Deterioration Leaning Value Clear.


d.

Press "Next".


e.

Press "Exit".


f.

Enter the menu options in this order: Powertrain / Engine / Utility / DPF Deposition Value Clear.


g.

Press "Next".


h.

Press "Exit".



CRANK TIME COMPENSATION LEARNING VALUE CLEAR FUNCTION


·

This procedure uses the GTS to perform "Crank Time Compensation Learning Value Clear".

·

When replacing the crank angle sensor plate (crankshaft), perform "Crank Time Compensation Learning Value Clear".


HINT:
·

If an error occurs during compensation reset, check the vehicle condition, and then perform compensation reset again.

·

A communication malfunction may occur if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.



a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.

NOTICE:

Do not start the engine.



c.

Enter the following menus: Powertrain / Engine / Utility / Crank Time Compensation Learning Value Clear.


d.

When the first screen is displayed, check the vehicle condition and push "Next".


e.

When the screen indicating reset completion is displayed, push "Exit".



A/F SENSOR LEARNING VALUE CLEAR FUNCTION


·

This procedure uses the GTS to perform "A/F Sensor Learning Value Clear".

·

When replacing the No. 1 nitrogen oxides sensor, replace the sensor and then perform "A/F Sensor Learning Value Clear".

HINT:

The No. 1 nitrogen oxides sensor has an air fuel ratio sensor function. Therefore, perform "A/F Sensor Learning Value Clear" after replacing the No. 1 nitrogen oxides sensor.



HINT:
·

If an error occurs during compensation reset, check the vehicle condition, and then perform compensation reset again.

·

A communication malfunction may occur if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.



a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.

NOTICE:

Do not start the engine.



c.

Enter the following menus: Powertrain / Engine / Utility / A/F Sensor Learning Value Clear.


d.

When the first screen is displayed, check the vehicle condition and press "Next".


e.

When the screen indicating reset completion is displayed, press "Exit".



i-ART Learning Value Reset


NOTICE:
·

When the engine is started after the i-ART learned value is reset with the engine switch on (IG), the value for "Injection Feedback Value" may indicate a malfunction momentarily. However, this is not a malfunction and is due to the i-ART learned value being reset. The value returns to normal once learning is begun.

·

When the battery cable is disconnected, reconnect the battery cable, turn the engine switch on (IG) and wait 3 minutes or more before performing this procedure.



a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.

NOTICE:

Do not start the engine.



c.

Enter the following menus: Powertrain / Engine / Utility / i-ART Learning Value Reset.

·

3 minutes or more has elapsed after turning the engine switch on (IG) and connecting the battery cable.

·

The engine is stopped.

·

Battery voltage is 8 V or more.



d.

Select the cylinder to be reset.


e.

Press "Next".

HINT:

The reset is performed automatically after "Next" is selected.



f.

If the reset fails, confirm the following conditions and perform the reset again.

i.

Turn the engine switch on (IG).


ii.

Turn the engine switch off and wait for 30 seconds or more.


iii.

Turn the engine switch on (IG) and wait 3 minutes or more.


iv.

Battery voltage is 8 V or more.



g.

When the screen indicating reset completion is displayed, push "Exit".