Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › from 2020.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261052 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  U0100  Lost Communication with ECM / PCM  U0140  Lost Communication with Main Body ECU  U0142  Lost Communication with Main Body ECU  U0155  Lost Communication with Combination Meter  U1103  Lost Communication with Stop and Start Control Module  U1117  Lost Communication with Accessory Gateway  


DESCRIPTION

These DTCs are stored when there is a CAN communication error between the certification ECU (smart key ECU assembly), ECM, main body ECU (multiplex network body ECU), combination meter assembly or engine stop and start ECU*, and data from the option connector (bus buffer ECU) cannot be received.

*: w/ Stop and Start System


DTC No. Detection Item DTC Detection Condition Trouble Area Note
U0100 Lost Communication with ECM / PCM CAN communication error between certification ECU (smart key ECU assembly) and ECM (1-trip detection logic*) ECM
DTC Output Confirmation Operation:

Turn the engine switch on (IG) and wait 10 seconds or more.


U0140 Lost Communication with Main Body ECU CAN communication error between certification ECU (smart key ECU assembly) and main body ECU (multiplex network body ECU) (1-trip detection logic*) Main body ECU (multiplex network body ECU)
DTC Output Confirmation Operation:

Always


U0142 Lost Communication with Main Body ECU CAN communication error between certification ECU (smart key ECU assembly) and main body ECU (multiplex network body ECU) (1-trip detection logic*) Main body ECU (multiplex network body ECU)
DTC Output Confirmation Operation:

Always


U0155 Lost Communication with Combination Meter CAN communication error between certification ECU (smart key ECU assembly) and combination meter assembly (1-trip detection logic*) Combination meter assembly
DTC Output Confirmation Operation:

Turn the engine switch on (IG) and wait 10 seconds or more.


U1103 Lost Communication with Stop and Start Control Module CAN communication malfunction between the certification ECU (smart key ECU assembly) and engine stop and start ECU (1-trip detection logic*). Engine stop and start ECU
DTC Output Confirmation Operation:

Turn the engine switch on (IG) and wait 10 seconds or more.


U1117 Lost Communication with Accessory Gateway Data from the option connector (bus buffer ECU) cannot be received.
·

Connector and branch wire of sub bus 2 of option connector (bus buffer ECU)

·

Internal malfunction of option connector (bus buffer ECU)


DTC Output Confirmation Operation:

Turn the engine switch on (IG) and wait 10 seconds or more.



*: Only detected while a malfunction is present.


Vehicle Condition and Fail-safe Function when Malfunction Detected
DTC No. Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
U0100 There is no effect on vehicle behavior. If the following conditions are met, it can be determined that the malfunction is not in the direct line (NE) but in CAN communication.
·

When the engine switch is pressed, the system controls the engine based on the engine speed signal via direct line, causing the engine to stop cranking.

·

When the engine switch is pressed and held, the system controls the engine based on the engine speed signal via direct line, causing the engine to stop cranking.


If the following conditions are met, it can be determined that there is a malfunction in both CAN communication and the direct line (NE).
·

When the engine switch is pressed, the engine stops cranking after 6 seconds.

·

When the engine switch is pressed and held, the engine remains cranking for up to 30 seconds.


U0140
U0142
·

Doors cannot be locked or unlocked.

·

The warning (wireless buzzer) does not sound.


-
U0155
·

The warning (meter buzzer) does not sound and the meter does not indicate a warning.

·

There is no effect on vehicle behavior.


-
U1103
·

The engine stall misjudgment is done by the idling stop by stop and start system.

·

Immobiliser set is done by the door operation in the idling stop by stop and start system


-
U1117 The engine cannot be started using the wireless remote control function. -

Related Data List and Active Test Items
DTC No. Data List and Active Test
U0100
U0140
U0142
U0155
U1103
U1117
-

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


PROCEDURE

1.CHECK FOR DTC

NEXT

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)