Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) › from 2020.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261067 ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)  B279A12  Engine Immobiliser System Circuit Short to Battery  


DESCRIPTION

If the communication line (EFIO-IMI) to the transponder key ECU assembly is stuck high (e.g. shorted to +B), the ECM stores this DTC.

DTC No. DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B279A12 Communication line (EFIO-IMI) between the ECM and transponder key ECU assembly is stuck high.
·

Harness or connector

·

ECM

·

Transponder key ECU assembly


Turn the ignition switch to ON and wait 6 seconds.

Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started (initial ignition occurs and engine cranks, then ignition stops) Engine cannot be started

Related Data List and Active Test
DTC No. Data List and Active Test
B279A12 -

WIRING DIAGRAM

B365296E12
1.052,1.958 2.969,2.156 1.917,0.198 10 false G185 1.063,2.146 1.458,2.365 0.396,0.219 10 false ECM 5.25,2.156 6.656,2.469 1.406,0.313 10 false Transponder Key ECU Assembly 1.479,1.104 1.781,1.344 0.302,0.24 10 false IMI 5.469,1.104 5.833,1.26 0.365,0.156 10 false EFIO 5.229,1 5.458,1.208 0.229,0.208 10 false 13 1.792,1 3.792,1.198 2,0.198 10 false 16 5.25,1.958 6.771,2.177 1.521,0.219 10 false G74

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or ECM is replaced, refer to the Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.



PROCEDURE

2.CHECK FOR DTC
a.

Perform "DTC Output Confirmation Operation" procedure.




OK

NG

3.CHECK CONNECTION OF CONNECTOR
3.CHECK CONNECTION OF CONNECTOR
a.

Check that the connectors are properly connected to the ECM and transponder key ECU assembly.

OK:

Connectors are properly connected.




OK

4.CHECK ECM (TERMINAL IMI)

NG

CONNECT CONNECTORS PROPERLY

4.CHECK ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

B598245C03
5.958,0.76 6.427,0.99 0.469,0.229 5.542,2.156 5.875,1.469 true 3.125,4.625 3.271,4.625 3.271,4.625 3.271,4.063 true 3.635,4.625 3.469,4.625 3.469,4.625 3.469,4.063 true 0.167,0.094 0.479,0.25 0.313,0.156 10 false *a 3.667,4.531 3.979,4.688 0.313,0.156 10 false *d 0.948,4.052 1.417,4.208 0.469,0.156 10 false GND 6.021,0.813 6.427,0.99 0.406,0.177 10 false G185 5.438,2.208 5.771,2.375 0.333,0.167 10 false IMI 3.292,3.031 3.604,3.188 0.313,0.156 10 false *b 2.938,4.531 3.25,4.688 0.313,0.156 10 false *c

Text in Illustration
*a Component with harness connected
(ECM)
*b Waveform
*c Approximately 160 ms *d Approximately 270 ms

Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition
G185-16 (IMI) - Body ground Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)


OK:

Waveform is similar to that shown in the illustration.




OK

5.CHECK ECM (TERMINAL IMI)

NG

5.CHECK ECM (TERMINAL IMI)
a.
B592589E01
1.552,0.26 2.01,0.51 0.458,0.25 2.823,0.5 2.635,0.5 2.635,0.5 2.052,1.302 true 1.646,0.313 2.104,0.51 0.458,0.198 10 false G74 2.938,0.438 3.396,0.635 0.458,0.198 10 false EFIO 0.094,0.115 0.552,0.313 0.458,0.198 10 false *a

Disconnect the transponder key ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G74-13 (EFIO) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Transponder Key ECU Assembly)



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
6.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
a.

Disconnect the G74 transponder key ECU assembly connector.


b.

Disconnect the G185 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G74-13 (EFIO) - G185-16 (IMI) Always Below 1 Ω
G74-13 (EFIO) or G185-16 (IMI) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G185-16 (IMI) - Body ground Always Below 1 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR