Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › from 2020.08
RM27T0E _56 Audio / Visual / Telematics _053720 AUDIO / VIDEO _0260969 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Sound Signal Circuit between Radio Receiver and Stereo Component Amplifier  


DESCRIPTION

The radio and display receiver assembly sends a sound signal to the stereo component amplifier assembly via this circuit.

The sound signal that is sent is amplified by the stereo component amplifier assembly, and then is sent to the speakers.

If there is an open or short in this circuit, sound cannot be heard from the speakers even if the stereo component amplifier assembly or speakers are not malfunctioning.

WIRING DIAGRAM

E402621E38
5.583,2.396 6.74,2.854 1.156,0.458 10 false H105 1.229,1.542 2.385,2 1.156,0.458 10 false FL- 1.188,1.125 2.344,1.583 1.156,0.458 10 false FL+ 1.208,0.698 2.365,1.156 1.156,0.458 10 false FR- 1.188,0.292 2.344,0.75 1.156,0.458 10 false FR+ 1.583,0.198 2.74,0.656 1.156,0.458 10 false 1 1.594,0.604 2.75,1.063 1.156,0.458 10 false 6 1.594,1.01 2.75,1.469 1.156,0.458 10 false 2 1.594,1.438 2.75,1.896 1.156,0.458 10 false 7 3.563,1.865 4.719,2.323 1.156,0.458 10 false * 0.458,2.406 1.615,2.865 1.156,0.458 10 false H95 0.458,2.563 1.677,2.99 1.219,0.427 10 false Radio and Display Receiver Assembly 5.656,2.031 6.813,2.49 1.156,0.458 10 false SLD 5.677,1.542 6.833,2 1.156,0.458 10 false L- 5.677,1.135 6.833,1.594 1.156,0.458 10 false L+ 5.667,0.292 6.823,0.75 1.156,0.458 10 false R+ 5.708,0.698 6.865,1.156 1.156,0.458 10 false R- 5.406,1.896 5.802,2.292 0.396,0.396 10 false 6 5.406,1.438 5.802,1.833 0.396,0.396 10 false 2 5.396,1.021 5.792,1.417 0.396,0.396 10 false 3 5.406,0.188 5.802,0.583 0.396,0.396 10 false 5 5.396,0.594 5.792,0.99 0.396,0.396 10 false 4 0.333,3.313 1.49,3.552 1.156,0.24 10 false *: Shielded 5.573,2.552 6.792,2.979 1.219,0.427 10 false Stereo Component Amplifier Assembly

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the H95 radio and display receiver assembly connector.


b.

Disconnect the H105 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H105-5 (R+) - H95-1 (FR+) Always Below 1 Ω
H105-4 (R-) - H95-6 (FR-) Always Below 1 Ω
H105-3 (L+) - H95-2 (FL+) Always Below 1 Ω
H105-2 (L-) - H95-7 (FL-) Always Below 1 Ω
H105-6 (SLD) - Body ground Always 10 kΩ or higher
H105-5 (R+) - Body ground Always 10 kΩ or higher
H105-4 (R-) - Body ground Always 10 kΩ or higher
H105-3 (L+) - Body ground Always 10 kΩ or higher
H105-2 (L-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR