Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › from 2020.08
RM27T0E _56 Audio / Visual / Telematics _053720 AUDIO / VIDEO _0260969 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Radio Receiver Power Source Circuit  


DESCRIPTION

This is the power source circuit to operate the radio and display receiver assembly.

WIRING DIAGRAM

E384853E20
0.927,0.24 2.979,0.417 2.052,0.177 10 false from Engine Stop and Start ECU 1.5,0.615 2.906,0.927 1.406,0.313 10 false from Battery 0.969,1.208 2.302,1.406 1.333,0.198 10 false from IG NO.1 Relay 0.948,1.823 3,2 2.052,0.177 10 false from Engine Stop and Start ECU 5.896,3.083 7.104,3.49 1.208,0.406 10 false Radio and Display Receiver Assembly 3.333,0.781 4.427,1 1.094,0.219 10 false RADIO NO.1 3.219,1.385 4.271,1.635 1.052,0.25 10 false ECU-IG NO.2 3.521,2.365 4.188,2.656 0.667,0.292 10 false ACC 5.677,0.594 6.042,0.781 0.365,0.188 10 false H92 5.688,1.229 6.052,1.417 0.365,0.188 10 false H93 5.688,2.208 6.052,2.396 0.365,0.188 10 false H92 5.688,2.781 6.052,2.969 0.365,0.188 10 false H92 6.083,0.594 6.448,0.781 0.365,0.188 10 false +B1 6.104,1.219 6.469,1.406 0.365,0.188 10 false IG 6.083,2.188 6.51,2.375 0.427,0.188 10 false ACC1 6.083,2.75 6.51,2.938 0.427,0.188 10 false GND1 5.729,1.01 5.938,1.198 0.208,0.188 10 false 19 5.719,1.979 5.927,2.167 0.208,0.188 10 false 15 5.76,0.385 5.906,0.563 0.146,0.177 10 false 4 5.75,2.563 5.896,2.74 0.146,0.177 10 false 1 3.635,0.135 3.844,0.323 0.208,0.188 10 false *1 3.667,1.729 3.875,1.917 0.208,0.188 10 false *1 3,0.49 3.208,0.677 0.208,0.188 10 false *2 3,2.083 3.208,2.271 0.208,0.188 10 false *2 1.229,2.198 2.302,2.385 1.073,0.188 10 false from ACC Relay 0.333,2.948 2.385,3.125 2.052,0.177 10 false *1: w/ Stop and Start System 0.333,3.323 2.385,3.5 2.052,0.177 10 false *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure. (w/o Stop and Start System)


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY POWER SOURCE)
a.
E365519C52
0.708,0.938 1.083,1.24 0.375,0.302 2.281,0.948 2.656,1.25 0.375,0.302 1.927,1.813 1.719,0.635 1.719,0.635 1.552,0.635 true 3.063,1.813 2.823,0.51 2.823,0.51 2.656,0.51 true 0.51,2.573 0.344,2.573 0.344,2.573 0.292,2.063 true 3.052,1.948 2.896,2.635 2.896,2.635 2.75,2.635 true 2.354,1.021 2.813,1.219 0.458,0.198 10 false H92 0.781,1.01 1.24,1.208 0.458,0.198 10 false H93 2.375,0.438 2.688,0.635 0.313,0.198 10 false +B1 2.365,2.552 2.813,2.802 0.448,0.25 10 false ACC1 1.146,0.552 1.594,0.802 0.448,0.25 10 false GND1 0.563,2.5 1.01,2.75 0.448,0.25 10 false IG 0.156,0.146 0.604,0.396 0.448,0.25 10 false *a
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H92-1 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H92-4 (+B1) - H92-1 (GND1) Always 11 to 14 V*1
10.5 to 16 V*2
H92-15 (ACC1) - H92-1 (GND1) Ignition switch ACC 11 to 14 V*1
10.5 to 16 V*2
H93-19 (IG) - H92-1 (GND1) Ignition switch ON 11 to 14 V


*1: w/o Stop and Start System

*2: w/ Stop and Start System



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR