STOP AND START CONTROL
The stop and start system operates according to the following conditions, achieving appropriate engine stop and start control together with safe and smooth driving characteristics.
When all of the conditions in the following table have been met, the engine is stopped by stop and start control.
| Item | Condition
(All of the following conditions are met) |
|
|---|---|---|
| Idle Stop | Push start switch assembly | 5 seconds or more have passed with the engine switch on (IG) |
| Engine Coolant Temperature | 48.1 to 105°C (119 to 221°F) | |
| Ambient Temperature | -5°C (23°F) or higher | |
| Driver Door | 3 seconds have elapsed after driver door closed | |
| Driver Seat Belt | 3 seconds have elapsed after driver seat belt fastened | |
| Brake Master Cylinder Fluid Pressure*1 | 1.1 MPa or higher (10.2 kgf/cm2, 145 psi) (changes according to gradient) | |
| Shift Position | After shift lever is operated and 1 second elapses, shift lever is in P or D | |
| Drive Mode | ECO or NORMAL mode | |
| Air suspension control | Air suspension not operating | |
| Automatic Transmission Fluid Temperature | ·
20 to 110°C (68 to 230°F) ·
Other than when stop and start control is prohibited due to insufficient automatic transmission fluid pressure, etc. |
|
| Stop and Start System Cancel Switch (Eco run Cancel Switch Assembly) | Off (System control is not prohibited) | |
| Vehicle Speed | 0 km/h (0 mph) (After the engine warms up) | |
| Road Grade | -6 to 8° (-1.02 to 1.36 m/s2) | |
| Engine Speed | 1250 rpm or less | |
| Hood | 3 seconds have elapsed after hood closed | |
| Battery Voltage | When using specified battery:
7.6 V or higher when starter begins operation and 7.6 V or higher when cranking When using non-specified battery:
8.92 V or higher when starter begins operation and 8.92 V or higher when cranking |
|
| Battery Fluid Temperature*2 | -10°C or higher and 70°C or less (14°F or higher and 158°F or less) | |
| Battery Integrated Current*3 | One of the following conditions is met:
·
-17971 A-sec or more: "Status of Battery Charge Control"*4 is Charge Control Coordination Mode, Stop and Start Standalone Mode, Low Temperature Mode or Temperature High/Low Mode ·
0 A-sec or more: "Status of Battery Charge Control"*4 is Stop and Start Restriction Mode |
|
| Battery Charge Control*4 | The value of Data List item Status of Battery Charge Control*4 is not Refresh Charge Mode, Abnormal Mode or Battery Condition Judgment Mode. | |
| Idling Stop Rate
Total Idling Stop Rate |
·
Idling stop rate: less than 50% ·
Total idling stop rate: less than 40%
|
|
| Air Conditioning | Any of the following conditions are met:
·
Defogger Switch: OFF, and Blower Switch: OFF ·
With blower switch on, evaporator temperature below threshold (varies depending on each temperature, humidity, insolation, etc.) and after certain period of time since engine restarted by stop and start system (threshold varies depending on idling stop conditions) |
|
| Heater:
Any of the following conditions are met: ·
Blower Switch: OFF ·
Blower Switch: ON, and A/C Switch: OFF (Ambient temperature higher than 10°C (50°F), engine coolant temperature higher than 55°C (131°F), or vehicle cabin temperature more than 5°C (41°F) lower than the set temperature) ·
Blower Switch: ON, and A/C Switch: OFF (after certain period of time since engine restarted by stop and start system) |
||
| Cooler:
Any of the following conditions are met: ·
Blower Switch: OFF ·
A/C switch: OFF ·
Ambient temperature 23°C (73°F) or less ·
Evaporator internal temperature less than 9°C (48°F), air mix damper opening value more than 10%, and vehicle cabin temperature less than 3°C (37°F) above set temperature or blower level less than 16 (when engine switch turned on for first time in one trip) |
||
| Steering Operation | When the steerage angle of the steering wheel is 45 degrees or less. | |
| Engine Control | Engine catalytic warm up is completed
·
Engine catalytic warm up is completed ·
Engine control learning has completed ·
Automatic transmission control learning has completed |
|
*1: Enough brake force is applied to prevent the vehicle from moving when the engine is started again.
*2: When the battery fluid temperature is -15°C (5°F) or less, or 75°C (167°F) or higher, stop and start control is prohibited. When the battery fluid temperature returns to -10°C (14°F) or higher, and 70°C (158°F) or less, stop and start control is permitted.
*3: Read the Data List items "Integrated Current" and "Stop&Start Operating Permission (Integrated Current)" when checking the integrated current value.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DATA LIST / ACTIVE TEST
*4: Please refer to the Data List "Status of Battery Charge Control" for information about the status of the battery charge control.
When the engine is stopped by stop and start control, and any of the following conditions are met, the engine will restart.
| Item | Condition
(Any of the following conditions is met) |
|
|---|---|---|
| Engine Restart | ECD System | Malfunction in ECD System is detected |
| Automatic Transmission System | Malfunction in automatic transmission system is detected | |
| Electromagnetic Oil Pump | Electromagnetic oil pump malfunctioning | |
| Power Steering System | Malfunction in power steering system is detected | |
| Vehicle Stability Control System | Malfunction in vehicle stability control system is detected | |
| Air Conditioning | Timer in the air conditioning amplifier assembly runs out | |
| Heater | Timer in the air conditioning amplifier assembly runs out | |
| Air Conditioning/Heater | Both of the following conditions are met:
·
Blower switch: ON ·
Evaporator temperature exceeds threshold value (threshold value varies with temperature, humidity and amount of solar radiation) Any of the following conditions are met:
·
A/C switch, blower switch: ON ·
Defogger switch: ON ·
Blower switch turned off during auto control or blower mode changed to manual ·
Changes from stop and start system priority control to normal system control |
|
| Shift Position | Move the shift lever from P or D to other position | |
| Battery | Battery voltage drops (11.4 V or less) | |
| Battery Integrated Current* | The accumulated value of discharge current during engine stop is too large (6912 A-sec or more) | |
| Vehicle Speed | Vehicle speed signal is input (Vehicle stopped on a slope, etc.) | |
| Drive Mode | Other than ECO mode or NORMAL mode | |
| Driver Door | Open | |
| Driver Seat Belt | Driver seat belt is unfastened | |
| Steering Operation | Steering wheel turned 25 degrees or more | |
| Brake Master Cylinder Fluid Pressure | Brake master cylinder fluid pressure decreases (Brake pedal released) | |
| Accelerator Pedal | Accelerator pedal is depressed | |
| Stop and Start System Cancel Switch (Eco run Cancel Switch Assembly) | Off (System control is not prohibited) → ON (System control is prohibited) | |
| Air suspension control | Air suspension operating (When car height switch is operated, etc.) | |
*: Read the Data List items "Integrated Current" and "Stop&Start Operating Permission (Integrated Current)" when checking the integrated current value.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DATA LIST / ACTIVE TEST
WARNING CONTROL
If any of the following operations are performed while the engine is stopped due to stop and start control, the system will not restart the engine. The engine will change the mode from "stopped due to system control" to "stalled" or the driver will be warned using the buzzer.
| Operation | Warning Control |
|---|---|
| The engine hood is opened with the shift lever in D | The engine stops (mode changes to "stalled", and the engine cannot be restarted until the engine switch is turned off and then on (IG)) |
| The driver door is opened with the shift lever in D | The engine starts, warning buzzer sounds and stop and start indicator blinks |
| The driver seat belt is unfastened | The engine starts |
WARNING INDICATOR AND BUZZER OPERATION
| *a | Stop and Start Indicator Light |
| *b | Stop and Start Cancel Indicator Light |
The driver is informed of the system control status and warnings by the stop and start indicator light, stop and start cancel indicator light and the buzzer.
| Item | Condition | Stop and start indicator light | Stop and start cancel indicator light | Buzzer |
|---|---|---|---|---|
| For 3 seconds after the engine switch on (IG) | Normal operation | Comes on | Comes on | Does not sound |
| During stop and start control operation (engine is stopped) | Normal operation | Comes on | Does not come on | Does not sound |
| Driver door opened | The blinking interval 0.3 seconds* | Does not come on | Sounds* | |
| After engine started by stop and start control | Driver door opened within 5 seconds of engine start | The blinking interval 0.3 seconds* | Does not come on | Sounds* |
| Control is prohibited by the stop and start system cancel switch (eco run cancel switch assembly) | Normal operation | Does not come on | Comes on | Does not sound |
| Diagnostic trouble code | Any DTCs are stored | Does not come on | The blinking interval 0.5 seconds | Does not sound |
| Starter assembly life | Number of times the starter has been operated exceeds its limit | Does not come on | The blinking interval 0.5 seconds | Does not sound |
| Flywheel sub-assembly life | Number of times the engine start has been operated exceeds its limit | Does not come on | The blinking interval 0.5 seconds | Does not sound |
*: Shift lever in D
MULTI-INFORMATION DISPLAY MESSAGE AND INDICATOR OPERATION
An indicator and/or messages are displayed on the multi-information display to indicate condition of the stop and start system when certain vehicle conditions are met.
| Stop and Start System Condition | Multi-information Display Message*1 | Vehicle Condition | |
|---|---|---|---|
| When the engine cannot be stopped by the stop and start system |
*2 |
"Non-Dedicated Battery" | A non-specified battery for the stop and start system may have been installed. |
| "Battery Charging" | ·
The battery charge amount may be low. ·
A refresh charge may be occurring. |
||
| "Stop & Start Unavailable" | The engine may have been started with the hood opened. | ||
| "System Temperature Low" | The battery may be cold. | ||
| "System Temperature High" | The battery may be extremely hot. | ||
| "For Climate Control" | ·
The air conditioning system is being used when the ambient temperature is high or low. ·
Windshield defogger is pressed. |
||
| "Driver Seat Belt Unbuckled" | The driver seat belt is not fastened. | ||
| "Steering Wheel Turned" | The steering wheel is being turned. | ||
| "Depress Brake Firmly to Activate" | The brake pedal is not depressed enough. | ||
| When the engine automatically restarts while stopped by the stop and start system |
*2 |
"Driver Seat Belt Unbuckled" | The driver seat belt is not fastened. |
| "Steering Wheel Turned" | The steering wheel is turned. | ||
| "For Climate Control" | ·
The air conditioning system is turned on or the air conditioning is being used. ·
Windshield defogger is turned on. |
||
| "Battery Charging" | The battery charge amount may be low. | ||
| The system may be malfunctioning | - | "Stop & Start System Malfunction"
"Visit Your Dealer" |
- |
*1: Messages are listed in the order of priority.
*2: When the engine cannot be stopped by the stop and start system or the engine is restarted while the engine is stopped by the stop and start system, the following mark is displayed on the multi-information display.
STOP AND START SYSTEM OPERATION
Depending on the type of malfunction, stop and start control may be prohibited by the fail-safe function. The following table shows effects on the vehicle and areas to be inspected when there is a malfunction in the stop and start system.
| Malfunctioning Area | Malfunction | DTC Output | Data List / Freeze Frame Data | Effect on Vehicle | Area to be Inspected |
|---|---|---|---|---|---|
| IG2 circuit | Open | P253014 | IG Switch | Stop and start control prohibited | Wire harness or connector |
| +B circuit | Open | - | Data List cannot be checked because power not supplied to the engine stop and start ECU | Stop and start control prohibited | Wire harness or connector |
| CLL (park/neutral position switch assembly) circuit | Stuck on | P085014 | Neutral Switch | ·
Stop and start control prohibited ·
Stop and start cancel indicator blinks |
·
Wire harness or connector ·
Park/neutral position switch assembly |
| Stuck off | P085012 | ·
Stop and start control prohibited ·
Stop and start cancel indicator blinks |
|||
| BNT1 (engine hood courtesy switch) circuit | Stuck on | - | Hood Courtesy Switch | Mode does not change to "stalled" when engine hood opened with shift lever in D and engine stopped by stop and start control | ·
Wire harness or connector ·
Engine hood courtesy switch (Hood lock assembly) |
| Stuck off | - | Stop and start control prohibited despite engine hood being closed | |||
| ECAN (stop and start system cancel switch (eco run cancel switch assembly)) circuit | Stuck on | - | Stop&Start Cancel Switch | Stop and start control prohibited | ·
Wire harness or connector ·
Stop and start system cancel switch (eco run cancel switch assembly) |
| Stuck off | - | Stop and start control cannot be canceled by pressing the stop and start system cancel switch (eco run cancel switch assembly) | |||
| EMOP circuit
EGND circuit (Electromagnetic oil pump) |
·
Open ·
Shorted ·
Internal circuit malfunction |
·
P279612 ·
P279614 ·
P279796 |
·
Oil Pump Relay ·
Stop&Start Operating Permission (Electromagnetic Oil Pump) |
·
Stop and start control prohibited ·
Stop and start cancel indicator blinks |
·
Wire harness or connector ·
Transmission wire ·
Engine stop and start ECU ·
Electromagnetic oil pump ·
Engine stop and start solenoid filter |
| Electromagnetic oil pump | Electromagnetic oil pump malfunction | P094296 | Stop&Start Operating Permission (AT/CVT) | ·
Stop and start control prohibited ·
Stop and start cancel indicator blinks |
Electromagnetic oil pump |
| STA circuit | Overcurrent | P061519 | - | ·
Stop and start control prohibited ·
Stop and start cancel indicator blinks |
·
BBC NO. 2 fuse ·
BBC NO. 3 fuse ·
Wire harness or connector ·
ST relay ·
ST NO. 2 relay ·
Engine stop and start ECU |
| Stuck on | P164400 | ·
Wire harness or connector ·
ST relay ·
ST NO. 2 relay ·
Engine stop and start ECU |
|||
| Stuck off | P164400 | ||||
| BBC (backup boost converter) circuit | Overcurrent | P323A19 | State of BBC | ·
Stop and start control prohibited ·
Stop and start cancel indicator blinks |
·
BBC NO. 2 fuse ·
BBC NO. 3 fuse ·
Wire harness or connector ·
Engine stop and start ECU ·
Battery ·
ECUs and sensors connected to B41, B42, B43, IG41 and EMOP |
·
Open ·
Shorted ·
Internal circuit malfunction ·
Battery |
·
P30DF62 ·
P30EF4B ·
P323A00 ·
P323A16 ·
P323AA2 ·
P323B29 ·
P323B38 |
State of BBC | ·
Stop and start control prohibited ·
Stop and start cancel indicator blinks |
·
BBC NO. 2 fuse ·
BBC NO. 3 fuse ·
Wire harness or connector ·
Engine stop and start ECU ·
Battery |
|
| External backup boost converter (eco run vehicle converter assembly) circuit | ·
Open ·
Shorted ·
Internal circuit malfunction ·
Battery |
P33B300 | ·
State of External BBC ·
External BBC Overcurrent History |
·
Stop and start control prohibited ·
Stop and start cancel indicator blinks |
·
BBC NO. 1 fuse ·
Wire harness or connector ·
External backup boost converter (eco run vehicle converter assembly) ·
Battery |
| ECU inner circuit | Malfunction | P16449E | - | ·
Stop and start control prohibited ·
Stop and start cancel indicator blinks |
Engine stop and start ECU |
| Monitoring CPU circuit | Malfunction | P060629 | State of BBC | ·
Stop and start control prohibited ·
Stop and start cancel indicator blinks |
Engine stop and start ECU |
| EEPROM | Malfunction | P062F46 | - | ·
Stop and start control prohibited ·
Stop and start cancel indicator blinks |
Engine stop and start ECU |
| Starter delay circuit | Malfunction | P161D9E | Starter Motor | ·
Stop and start control prohibited ·
Stop and start cancel indicator blinks |
Engine stop and start ECU |
| Malfunctioning Area | Malfunction | DTC Output | Data List / Freeze Frame Data | Effect on Vehicle | Area to be Inspected |
|---|---|---|---|---|---|
| ECD system | MIL illuminated | DTCs for ECD system output | ·
Stop&Start Operating Permission (ECM 1) ·
Stop&Start Operating Permission (ECM 2) |
Stop and start control prohibited | ECD system |
| Abnormal NE signal | DTCs for ECD system output | - | ·
Stop and start control prohibited ·
Stop and start cancel indicator blinks |
·
ECD system (crank position sensor circuit) ·
Wire harness or connector |
|
| Crankshaft reverse rotation detection | DTCs for ECD system output | - | ·
Stop and start control prohibited ·
MIL illuminated |
ECD system (crank position sensor circuit) | |
| Charging system | Battery state sensor assembly malfunction | Charging system DTCs output | ·
Battery Fluid Temperature ·
Integrated Current |
Stop and start control prohibited | Charging system |
| Vehicle stability control system | VSC Running | - | ABS Running | Stop and start control prohibited | - |
| Malfunction in wheel speed sensor | Brake control system DTCs output | ·
Vehicle Speed ·
Wheel Speed Malfunction |
Stop and start control prohibited | ·
Wire harness or connector ·
Skid control ECU (Brake actuator assembly) ·
Vehicle speed sensor |
|
| Seat belt warning system | Malfunction in seat belt warning system | - | Driver Seat Belt Buckle Switch | ·
Stop and start control prohibited (stuck off) ·
Engine does not restart when it is stopped by stop and start control (stuck on) |
·
Front seat inner belt assembly (for driver side) ·
Wire harness or connector |
| Driver door courtesy light switch circuit | Malfunction in driver door courtesy light switch circuit | - | Driver Courtesy Switch Signal | ·
Stop and start control prohibited (stuck off) ·
Engine does not restart when it is stopped by stop and start control (stuck on) |
·
Front door courtesy light switch assembly (for driver side) ·
Driver door courtesy light switch circuit |
| Air conditioning system | Malfunction in ambient temperature sensor | Air conditioning system DTCs output | Ambient Temperature | Stop and start control prohibited | Ambient temperature sensor circuit |
| Power source | Backup boost converter malfunction | ·
P30DF62 ·
P30EF4B ·
P323A00 ·
P323A16 ·
P323AA2 ·
P323B29 ·
P323B38 |
State of BBC | ·
Stop and start control prohibited ·
Stop and start cancel indicator blinks |
·
BBC NO. 2 fuse ·
BBC NO. 3 fuse ·
Wire harness or connector ·
Engine stop and start ECU ·
Battery |
| Charging system malfunction | - | Alternator Status | Stop and start control prohibited | Charging system | |
| Charging control system | P160F00 | - | ·
Stop and start control prohibited ·
Stop and start cancel indicator blinks |
Charging system | |
| Number of starter operations | Exceeds the specified limit | P154563 | ·
Starter Operation # ·
Number of Engine Starts (IG-ON) ·
Number of Engine Starts (Stop & Start) |
·
Stop and start control prohibited ·
Stop and start cancel indicator blinks |
·
Starter assembly replacement is required. ·
ST relay replacement is required. ·
ST NO. 2 relay replacement is required. ·
Fuse replacement is required. |
| Usage limit for starting related parts | Flywheel sub-assembly usage limit | P154863 | Total Number of Engine Starts | ·
Stop and start control prohibited ·
Stop and start cancel indicator blinks |
Flywheel sub-assembly replacement is required |
| Starter signal malfunction | Signal does not match with the starter switch | P061562 | - | ·
Stop and start control prohibited ·
Stop and start cancel indicator blinks |
·
Wire harness or connector ·
Engine stop and start ECU |
| Jump start | Engine started with the engine hood open | - | Stop&Start Operating Prohibition (Jump Start) | Stop and start control prohibited
(permitted when the engine switch is turned off) |
·
Check for history of roadside service or jump start due to dead battery ·
Engine hood courtesy switch (Hood lock assembly) |
| CAN communication | Communication interrupted | ·
U010087 ·
U011487 ·
U012687 ·
U012987 ·
U013287 ·
U014087 ·
U015187 ·
U016487 |
- | ·
Stop and start control prohibited ·
Stop and start cancel indicator blinks |
·
Applicable wire harness or connector ·
Applicable ECU |