Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2020.08
RM27T0E _51 Engine / Hybrid System _091546 STOP AND START _0437376 STOP AND START SYSTEM U

STOP AND START  STOP AND START SYSTEM  TERMINALS OF ECU  


ENGINE STOP AND START ECU


B412468E42
5.031,0.219 5.458,0.469 0.427,0.25 3.219,0.208 3.646,0.458 0.427,0.25 1.563,0.208 1.99,0.458 0.427,0.25 3.271,0.25 3.729,0.448 0.458,0.198 10 false G313 1.604,0.25 2.063,0.448 0.458,0.198 10 false G312 5.094,0.26 5.552,0.458 0.458,0.198 10 false G314

a.

Disconnect the engine stop and start ECU connectors.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G312-1 (BIN2) - Body ground W - Body ground Battery Always 9.5 to 14 V
G312-2 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω
G312-3 (BIN1) - Body ground R - Body ground Battery Always 9.5 to 14 V
G312-8 (GND1) - Body ground W-B - Body ground Ground Always Below 1 Ω
G313-1 (+B) - Body ground GR - Body ground Power source of engine stop and start ECU Engine switch on (IG) 9.5 to 14 V
G313-6 (DGND) - Body ground W-B - Body ground Ground Always Below 1 Ω
G313-10 (NE) - Body ground P - Body ground Engine speed signal from ECM Always 10 kΩ or higher
G314-13 (CANH) - Body ground R - Body ground CAN communication Always 200 Ω or higher
G314-14 (CANL) - Body ground W - Body ground CAN communication Always 200 Ω or higher
G314-18 (IG2) - Body ground W - Body ground Push start switch assembly signal Engine switch on (IG) 9.5 to 14 V
G314-19 (ACC) - Body ground P - Body ground Push start switch assembly signal Engine switch on (ACC) 9.5 to 14 V
G314-20 (ILL) - Body ground G - Body ground Headlight dimmer switch (light control switch) tail signal input Headlight dimmer switch (light control switch) in tail or head position 9.5 to 14 V
G314-21 (IG1) - Body ground G - Body ground Push start switch assembly signal Engine switch on (IG) 9.5 to 14 V


c.

Reconnect the engine stop and start ECU connectors.


d.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G313-7 (BNT1) - G313-6 (DGND) B - W-B Engine hood courtesy switch (Hood lock assembly) signal
·

Engine switch on (IG)

·

Engine stopped

·

Engine hood open


0 to 1.5 V
·

Engine switch on (IG)

·

Engine stopped

·

Engine hood closed


8 to 14 V
G313-10 (NE) - G313-6 (DGND) P - W-B Engine speed signal from ECM Idling after engine warmed up Pulse generation
(see waveform 1)
G313-17 (CLL) - G313-6 (DGND) B - W-B Park/neutral position switch assembly signal
·

Engine switch on (IG)

·

Shift lever not in P or N


8 to 14 V
·

Engine switch on (IG)

·

Shift lever in P or N


Below 3.0 V
G313-19 (DON2) - G313-6 (DGND) W - W-B External backup boost converter (eco run vehicle converter assembly) signal Engine running Pulse generation
(see waveform 2)
G313-21 (STA) - G313-6 (DGND) W - W-B Starter pinion operation signal Cranking 6.0 V or more
G313-23 (STA2) - G313-6 (DGND) R - W-B Starter motor operation signal Cranking 6.0 V or more
G314-1 (IG31) - G313-6 (DGND) G - W-B Backup boost converter signal Engine switch on (IG) 10.5 to 16 V
G314-2 (B41) - G313-6 (DGND) L - W-B Backup boost converter signal Engine switch on (IG) 10.5 to 16 V
G314-3 (IG41) - G313-6 (DGND) GR - W-B Backup boost converter signal Engine switch on (IG) 10.5 to 16 V
G314-5 (ECAN) - G313-6 (DGND) L - W-B Stop and start system cancel switch (eco run cancel switch assembly) signal
·

Engine switch on (IG)

·

Stop and start system cancel switch (eco run cancel switch assembly) push and held


0 to 1.5 V
·

Engine switch on (IG)

·

Stop and start system cancel switch (eco run cancel switch assembly) not pressed


8 to 14 V
G314-8 (EGND) - G312-8 (GND1) B - W-B Electromagnetic oil pump directions signal Either of the following conditions is met:
·

Engine stopped by stop and start control

·

Engine switch on (IG) (engine not running) and Active Test "Electromagnetic Oil Pump" being performed


Pulse generation
(see waveform 3)
G314-9 (EMOP) - G312-8 (GND1) W - W-B Electromagnetic oil pump directions signal Either of the following conditions is met:
·

Engine stopped by stop and start control

·

Engine switch on (IG) (engine not running) and Active Test "Electromagnetic Oil Pump" being performed


10.5 to 16 V
G314-10 (IG12) - G313-6 (DGND) R - W-B Backup boost converter signal Engine switch on (IG) 10.5 to 16 V
G314-11 (B43) - G313-6 (DGND) L - W-B Backup boost converter signal Always 10.5 to 16 V
G314-12 (B42) - G313-6 (DGND) R - W-B Backup boost converter signal Always 10.5 to 16 V
G314-18 (IG2) - G313-6 (DGND) W - W-B Push start switch assembly signal Engine switch on (ACC) Below 1 V
Engine switch on (IG) 9.5 to 14 V
G314-19 (ACC) - G313-6 (DGND) P - W-B Push start switch assembly signal Engine switch off Below 1 V
Engine switch on (ACC) 9.5 to 14 V
G314-21 (IG1) - G313-6 (DGND) G - W-B Push start switch assembly signal Engine switch on (ACC) Below 1 V
Engine switch on (IG) 9.5 to 14 V
G314-24 (AC41) - G313-6 (DGND) P - W-B Backup boost converter signal Engine switch on (ACC) 10.5 to 16 V
G314-25 (IL41) - G313-6 (DGND) G - W-B Backup boost converter signal Headlight dimmer switch (light control switch) in tail or head position 10.5 to 16 V


e.
A346371E01
2.802,1.01 3.26,1.208 0.458,0.198 10 false GND 0.271,0.104 1.5,0.302 1.229,0.198 10 false 5 V/DIV. 1.406,1.906 2.781,2.104 1.375,0.198 10 false 2 ms./DIV.

Waveform 1

Item Content
Tester Connection G313-10 (NE) - G313-6 (DGND)
Tool Setting 5 V/DIV., 2 ms./DIV.
Condition Idling after engine warmed up


f.
A199267E07
2.917,1.198 3.375,1.396 0.458,0.198 10 false GND 0.24,0.083 1.469,0.281 1.229,0.198 10 false 5 V/DIV. 1.417,1.927 2.792,2.125 1.375,0.198 10 false 2 ms./DIV.

Waveform 2

Item Content
Tester Connection G313-19 (DON2) - G313-6 (DGND)
Tool Setting 5 V/DIV., 2 ms./DIV.
Condition Engine running


g.
A345972E01
0.115,0.115 1.49,0.313 1.375,0.198 10 false 10 V/DIV. 1.281,1.896 2.052,2.094 0.771,0.198 10 false 20 ms./DIV. 0.115,1.396 0.573,1.594 0.458,0.198 10 false GND 0.219,1.135 0.531,1.333 0.313,0.198 10 false +B 0.104,0.875 0.719,1.073 0.615,0.198 10 false 43 V

Waveform 3

Item Content
Tester Connection G314-8 (EGND) - G312-8 (GND1)
Tool Setting 10 V/DIV., 20 ms./DIV.
Condition Either of the following conditions is met:
·

Engine stopped by stop and start control

·

Engine switch on (IG) (engine not running) and Active Test "Electromagnetic Oil Pump" being performed