Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2020.08
RM27T0E _51 Engine / Hybrid System _091546 STOP AND START _0437376 STOP AND START SYSTEM C

STOP AND START  STOP AND START SYSTEM  P033562  Crankshaft Position Sensor "A" Signal Compare Failure  


DESCRIPTION

The crank position sensor sends an engine speed signal (NE signal) to the ECM. The engine speed signal is then sent directly from the NEO terminal of the ECM to the engine stop and start ECU. Additionally, the ECM sends the engine speed to the engine stop and start ECU via CAN communication. The engine stop and start ECU compares the NE signal and engine speed received via CAN communication to check for errors in the NE signal.

If the NE signal is abnormal, the engine stop and start ECU will blink the stop and start cancel indicator and stores DTC P033562.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory Note
P033562 Crankshaft Position Sensor "A" Signal Compare Failure All of the following conditions are met for 10 seconds (2 trip detection logic):
·

Normal communication between the ECM and the engine stop and start ECU.

·

Engine speed (NE signal) is below 6000 rpm.

·

Difference between the NE signal that is sent directly from ECM and the engine speed that is sent via CAN is 300 rpm or higher.


·

Wire harness or connector

·

Crank position sensor

·

ECM

·

Engine stop and start ECU


Blinks DTC stored SAE Code: P0335

CONFIRMATION DRIVING PATTERN

CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item "Status of Battery Charge Control" changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery fluid temperature at 11°C (52°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item "Status of Battery Charge Control" cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the engine switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.

·

Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Start the engine and wait for at least 15 seconds.


e.

Check that DTCs are not output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR

A199262E07
3.177,2.427 3.177,3.021 false 1.198,1.146 2.417,1.438 1.219,0.292 10 false Engine Running 4.365,0.177 5.573,0.354 1.208,0.177 10 false Judgment Timing 3.49,1.729 4.302,1.906 0.813,0.177 10 false 15 seconds 6.292,2.833 6.656,3.01 0.365,0.177 10 false Time 1.333,2.385 2.417,2.615 1.083,0.229 10 false Engine Stopped 2.813,3.052 3.833,3.292 1.021,0.24 10 false Engine Started 4.115,3.302 6.313,3.51 2.198,0.208 10 false Judged Normal or Abnormal



STOP AND START SYSTEM OPERATION CHECK


Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>OPERATION CHECK


WIRING DIAGRAM

A318277E80
0.781,4.427 2.781,4.615 2,0.188 10 false : CAN Communication Line 0.354,3.604 2.427,3.802 2.073,0.198 10 false Crank Position Sensor 3.396,3.469 3.854,3.677 0.458,0.208 10 false ECM 5.542,3.938 6.854,4.323 1.313,0.385 10 false Engine Stop and Start ECU 5.146,1 6.917,1.344 1.771,0.344 10 false Certification ECU (Smart Key ECU Assembly) 0.365,3.417 0.677,3.573 0.313,0.156 10 false r7 2.729,2.042 3.104,2.323 0.375,0.281 10 false C152 2.75,2.531 3.135,2.76 0.385,0.229 10 false C152 2.729,3 3.094,3.24 0.365,0.24 10 false C152 5.146,0.781 5.604,0.979 0.458,0.198 10 false G213 4.219,2.042 4.677,2.24 0.458,0.198 10 false G184 4.219,2.521 4.677,2.719 0.458,0.198 10 false G184 4.219,2.99 4.677,3.188 0.458,0.198 10 false G184 5.427,2.052 5.885,2.25 0.458,0.198 10 false G313 5.438,2.521 5.833,2.688 0.396,0.167 10 false G314 5.438,3 5.813,3.198 0.375,0.198 10 false G314 5.427,3.479 5.885,3.677 0.458,0.198 10 false G313 5.875,2.052 6.188,2.25 0.313,0.198 10 false NE 5.865,0.448 6.177,0.646 0.313,0.198 10 false NE 5.865,2.531 6.406,2.74 0.542,0.208 10 false CANH 5.875,3 6.417,3.208 0.542,0.208 10 false CANL 5.865,3.49 6.406,3.698 0.542,0.208 10 false DGND 3.896,2.063 4.208,2.26 0.313,0.198 10 false NEO 3.792,2.542 4.333,2.75 0.542,0.208 10 false CANH 3.813,3.021 4.354,3.229 0.542,0.208 10 false CANL 3.156,2.063 3.469,2.26 0.313,0.198 10 false NE+ 3.167,2.542 3.479,2.74 0.313,0.198 10 false NE- 3.156,3.01 3.573,3.208 0.417,0.198 10 false VCNE 1.385,2.052 1.698,2.25 0.313,0.198 10 false NE+ 1.396,2.521 1.708,2.719 0.313,0.198 10 false NE- 1.406,3.01 1.656,3.198 0.25,0.188 10 false VC 1.708,1.938 1.865,2.135 0.156,0.198 10 false 1 1.708,2.427 1.865,2.625 0.156,0.198 10 false 2 1.708,2.906 1.865,3.104 0.156,0.198 10 false 3 2.833,1.854 3.146,2.052 0.313,0.198 10 false 28 2.823,2.323 3.281,2.521 0.458,0.198 10 false 19 2.833,2.802 3.292,3 0.458,0.198 10 false 20 4.302,1.854 4.615,2.052 0.313,0.198 10 false 23 4.302,2.333 4.615,2.531 0.313,0.198 10 false 17 4.292,2.792 4.604,2.99 0.313,0.198 10 false 28 5.521,1.854 5.833,2.052 0.313,0.198 10 false 10 5.521,2.333 5.833,2.531 0.313,0.198 10 false 13 5.51,2.802 5.823,3 0.313,0.198 10 false 14 5.563,3.281 5.719,3.479 0.156,0.198 10 false 6 5.615,0.313 5.927,0.51 0.313,0.198 10 false 14

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and total number of engine starts and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU, airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU assembly, perform learning of the external backup boost converter (eco run vehicle converter assembly).

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

When the engine stop and start ECU or electromagnetic oil pump is replaced, check the electromagnetic oil pump.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION



HINT:
·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA

·

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.CHECK DTC OUTPUT (ECD SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs

Result:
Result Proceed to
ECD system DTCs are output A
ECD system crank position sensor circuit DTC is output B




A

2.READ VALUE USING GTS (Engine Speed)

B

2.READ VALUE USING GTS (Engine Speed)
a.

Connect the GTS to the DLC3


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / Engine Speed.


e.

According to the display on the GTS, read the Data List.

OK:

Engine speed signal is input (the speeds displayed on the tachometer and the GTS are almost the same).



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ECM)
3.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ECM)
a.

Turn the engine switch off.


b.

Disconnect the engine stop and start ECU connector.


c.

Disconnect the ECM connector.


d.

Disconnect the certification ECU (smart key ECU assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G313-10 (NE) - G184-23 (NEO) Always Below 1 Ω
G313-10 (NE) - Body ground Always 10 kΩ or higher
G184-23 (NEO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)
a.

Disconnect the engine stop and start ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G313-6 (DGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK ENGINE STOP AND START ECU (NE SIGNAL INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK ENGINE STOP AND START ECU (NE SIGNAL INPUT)
a.

Connect an oscilloscope to the NE and DGND terminals of the engine stop and start ECU connector.

A456121C43
3.26,0.094 3.646,0.365 0.385,0.271 3.698,0.823 3.969,1.438 true 2.917,0.823 2.76,1.49 true 0.708,0.094 1.021,0.292 0.313,0.198 10 false *a 4,1.49 4.615,1.688 0.615,0.198 10 false DGND 2.646,1.5 3.26,1.698 0.615,0.198 10 false NE 3.281,0.156 3.896,0.354 0.615,0.198 10 false G313
*a Component with harness connected
(Engine Stop and Start ECU)
- -



b.

Start the engine.


c.
A346371E01
2.802,1.01 3.26,1.208 0.458,0.198 10 false GND 0.271,0.104 1.5,0.302 1.229,0.198 10 false 5 V/DIV. 1.406,1.906 2.781,2.104 1.375,0.198 10 false 2 ms./DIV.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tester Connection G313-10 (NE) - G313-6 (DGND)
Tool Setting 5 V/DIV., 2 ms./DIV.
Condition Idling with warm engine

Result:
Result Proceed to
Pulse generation
(See waveform)
A
Stuck at 0 to 1.5 V B
Stuck at 8 to 14 V C




A

B

6.CHECK ENGINE STOP AND START ECU (NE TERMINAL VOLTAGE)

C

6.CHECK ENGINE STOP AND START ECU (NE TERMINAL VOLTAGE)
a.

Disconnect the ECM connector.

A456121C43
3.26,0.094 3.646,0.365 0.385,0.271 3.698,0.823 3.969,1.438 true 2.917,0.823 2.76,1.49 true 0.708,0.094 1.021,0.292 0.313,0.198 10 false *a 4,1.49 4.615,1.688 0.615,0.198 10 false DGND 2.646,1.5 3.26,1.698 0.615,0.198 10 false NE 3.281,0.156 3.896,0.354 0.615,0.198 10 false G313
*a Component with harness connected
(Engine Stop and Start ECU)
- -



b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G313-10 (NE) - G313-6 (DGND) Engine switch on (IG) 8 to 14 V


HINT:

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.


Result:
Proceed to
OK
NG




OK

NG