Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2020.08
RM27T0E _51 Engine / Hybrid System _091546 STOP AND START _0437376 STOP AND START SYSTEM C

STOP AND START  STOP AND START SYSTEM  P158954  G Sensor Zero Point Calibration Incomplete  


DESCRIPTION

If the vehicle is driven before calibration of the deceleration sensor zero point is performed, the engine stop and start ECU stores DTC P158954 and blinks the stop and start cancel indicator.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory Note
P158954 G Sensor Zero Point Calibration Incomplete Both of the following conditions are met for 5 seconds or more (1 trip detection logic):
·

The vehicle speed is 3 km/h (2 mph) or more and skid control ECU (brake actuator assembly) communication is normal.

·

Deceleration sensor zero point calibration is incomplete


·

The deceleration sensor zero point calibration has not been performed.

·

Airbag sensor assembly

·

Engine stop and start ECU


Blinks DTC stored SAE Code: P1589

CONFIRMATION DRIVING PATTERN

CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item "Status of Battery Charge Control" changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery fluid temperature at 11°C (52°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item "Status of Battery Charge Control" cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the engine switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.

·

Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.


d.

Start the engine and warm it up.


e.

Drive the vehicle at 3 km/h (1.9 mph) or more for 5 seconds or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



f.

Check that DTCs are not output.



STOP AND START SYSTEM OPERATION CHECK


Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>OPERATION CHECK


CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and total number of engine starts and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU, airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU assembly, perform learning of the external backup boost converter (eco run vehicle converter assembly).

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

When the engine stop and start ECU or electromagnetic oil pump is replaced, check the electromagnetic oil pump.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION



HINT:
·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA

·

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.PERFORM REGISTRATION (DECELERATION SENSOR ZERO POINT CLEAR, DECELERATION SENSOR ZERO POINT CALIBRATION)
NOTICE:
·

Once the zero point is stored, it cannot be overwritten until the data is cleared. Be sure to perform zero point clear and calibration after replacing the airbag sensor assembly.

·

Park the vehicle on a level surface (grade: +/-1%). Do not shake the vehicle or open/close any of the doors during zero point calibration. To avoid vibration caused by the engine idling, do not start the engine.



a.

Clear the zero point calibration data. (*1)

i.

Turn the engine switch off.


ii.

Connect the GTS to the DLC3.


iii.

Move the shift lever to P and apply the parking brake.


iv.

Turn the engine switch on (IG).

HINT:

Do not start the engine.



v.

Turn the GTS on.


vi.

Enter the following menus: Powertrain / Stop and Start / Utility / Deceleration Sensor Zero Point Clear.

NOTICE:

When the deceleration sensor zero point is cleared, the system information stored in the engine stop and start ECU is also cleared. If the vehicle is driven for 5 seconds or more at 3 km/h (2 mph) or more in this condition, the engine stop and start ECU will store DTC P158954 and blink the stop and start cancel indicator.



vii.

Turn the engine switch off.



b.

Perform zero point calibration of the deceleration sensor.

i.

Check that the shift lever is in P.


ii.

Connect the GTS to the DLC3.


iii.

Check that the parking brake is applied.


iv.

Turn the engine switch on (IG).

HINT:

Do not start the engine.



v.

Turn the GTS on.


vi.

Enter the following menus: Powertrain / Stop and Start / Utility / Deceleration Sensor Zero Point Calibration.

HINT:

If DTC P158954 is stored, the stop and start cancel indicator light will blink.



vii.

While keeping the vehicle stationary, follow the prompts on the GTS screen. Check that "Complete" is displayed on the GTS screen.

NOTICE:

If zero point calibration fails, perform the registration procedure again from. (*1)




Result:
Proceed to
OK
NG



OK

END

NG

2.READ VALUE USING GTS (GRADIENT OF ROAD SURFACE)
2.READ VALUE USING GTS (GRADIENT OF ROAD SURFACE)
a.

Enter the following menus: Powertrain / Stop and Start / Data List / Gradient of Road Surface.


b.

Check the road gradient displayed on the GTS.

OK:
GTS Display Condition Normal Condition
Gradient of Road Surface
·

Engine switch on (IG)

·

Stop vehicle on level surface


-0.7 to 0.7 m/s2
·

Engine switch on (IG)

·

Stop vehicle on slope road


-0.7 m/s2 or less, or 0.7 m/s2 or higher



Result:
Proceed to
OK
NG



OK

3.CHECK AND REPLACE ENGINE STOP AND START ECU

NG

5.REPLACE AIRBAG SENSOR ASSEMBLY
3.CHECK AND REPLACE ENGINE STOP AND START ECU
a.

Check and replace the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>ENGINE STOP AND START ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.PERFORM REGISTRATION (DECELERATION SENSOR ZERO POINT CLEAR, DECELERATION SENSOR ZERO POINT CALIBRATION)
4.PERFORM REGISTRATION (DECELERATION SENSOR ZERO POINT CLEAR, DECELERATION SENSOR ZERO POINT CALIBRATION)
NOTICE:
·

Once the zero point is stored, it cannot be overwritten until the data is cleared. Be sure to perform zero point clear and calibration after replacing the airbag ECU assembly.

·

Park the vehicle on a level surface (grade: +/-1%). Do not shake the vehicle or open/close any of the doors during zero point calibration. To avoid vibration caused by the engine idling, do not start the engine.



a.

Clear the zero point calibration data. (*1)

i.

Turn the engine switch off.


ii.

Connect the GTS to the DLC3.


iii.

Move the shift lever to P and apply the parking brake.


iv.

Turn the engine switch on (IG).

HINT:

Do not start the engine.



v.

Turn the GTS on.


vi.

Enter the following menus: Powertrain / Stop and Start / Utility / Deceleration Sensor Zero Point Clear.

NOTICE:

When the deceleration sensor zero point is cleared, the system information stored in the engine stop and start ECU is also cleared. If the vehicle is driven for 5 seconds or more at 3 km/h (2 mph) or more in this condition, the engine stop and start ECU will store DTC P158954 and blink the stop and start cancel indicator.



vii.

Turn the engine switch off.



b.

Perform zero point calibration of the deceleration sensor.

i.

Check that the shift lever is in P.


ii.

Connect the GTS to the DLC3.


iii.

Check that the parking brake is applied.


iv.

Turn the engine switch on (IG).

HINT:

Do not start the engine.



v.

Turn the GTS on.


vi.

Enter the following menus: Powertrain / Stop and Start / Utility / Deceleration Sensor Zero Point Calibration.

HINT:

If DTC P158954 is stored, the stop and start cancel indicator light will blink.



vii.

While keeping the vehicle stationary, follow the prompts on the GTS screen. Check that "Complete" is displayed on the GTS screen.

NOTICE:

If zero point calibration fails, perform the registration procedure again from (*1).




Result:
Proceed to
NEXT



NEXT

END

5.REPLACE AIRBAG SENSOR ASSEMBLY

Result:
Proceed to
NEXT



NEXT

6.PERFORM REGISTRATION (DECELERATION SENSOR ZERO POINT CLEAR, DECELERATION SENSOR ZERO POINT CALIBRATION)
6.PERFORM REGISTRATION (DECELERATION SENSOR ZERO POINT CLEAR, DECELERATION SENSOR ZERO POINT CALIBRATION)
NOTICE:
·

Once the zero point is stored, it cannot be overwritten until the data is cleared. Be sure to perform zero point clear and calibration after replacing the airbag sensor assembly.

·

Park the vehicle on a level surface (grade: +/-1%). Do not shake the vehicle or open/close any of the doors during zero point calibration. To avoid vibration caused by the engine idling, do not start the engine.



a.

Clear the zero point calibration data. (*1)

i.

Turn the engine switch off.


ii.

Connect the GTS to the DLC3.


iii.

Move the shift lever to P and apply the parking brake.


iv.

Turn the engine switch on (IG).

HINT:

Do not start the engine.



v.

Turn the GTS on.


vi.

Enter the following menus: Powertrain / Stop and Start / Utility / Deceleration Sensor Zero Point Clear.

NOTICE:

When the deceleration sensor zero point is cleared, the system information stored in the engine stop and start ECU is also cleared. If the vehicle is driven for 5 seconds or more at 3 km/h (2 mph) or more in this condition, the engine stop and start ECU will store DTC P158954 and blink the stop and start cancel indicator.



vii.

Turn the engine switch off.



b.

Perform zero point calibration of the deceleration sensor.

i.

Check that the shift lever is in P.


ii.

Connect the GTS to the DLC3.


iii.

Check that the parking brake is applied.


iv.

Turn the engine switch on (IG).

HINT:

Do not start the engine.



v.

Turn the GTS on.


vi.

Enter the following menus: Powertrain / Stop and Start / Utility / Deceleration Sensor Zero Point Calibration.

HINT:

If DTC P158954 is stored, the stop and start cancel indicator light will blink.



vii.

While keeping the vehicle stationary, follow the prompts on the GTS screen. Check that "Complete" is displayed on the GTS screen.

NOTICE:

If zero point calibration fails, perform the registration procedure again from (*1).




Result:
Proceed to
OK
NG



OK

END

NG