Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2020.08
RM27T0E _51 Engine / Hybrid System _091546 STOP AND START _0437376 STOP AND START SYSTEM C

STOP AND START  STOP AND START SYSTEM  P253014  Ignition Switch Circuit Short to Ground or Open  


DESCRIPTION

If the engine stop and start ECU receives the OFF signal from the certification ECU (smart key ECU assembly) when communication with the ECM is normal, the engine stop and start ECU will store DTC P253014.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory Note
P253014 Ignition Switch Circuit Short to Ground or Open All of the following conditions are met for 10 seconds or more (1 trip detection logic):
·

Engine switch off signal is input.

·

Communication with the ECM is normal.

·

Engine switch (communication) to on (IG).


·

Wire harness or connector

·

NO. 1 INTEGRATION RELAY (EFI MAIN NO. 1, IG2 relay)

·

Certification ECU (Smart key ECU assembly)

·

Engine stop and start ECU


Does not come on DTC stored SAE Code: P2531

CONFIRMATION DRIVING PATTERN

CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item "Status of Battery Charge Control" changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery fluid temperature at 11°C (52°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item "Status of Battery Charge Control" cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the engine switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.

·

Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.


d.

Start the engine and warm it up.


e.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



f.

Depress the brake pedal and stop the vehicle.


g.

Keep the engine stopped by stop and start control for 10 second or more. (Keep the shift lever in D.)


h.

Release the brake pedal with the shift lever in D to start the engine.


i.

Check that DTCs are not output.



STOP AND START SYSTEM OPERATION CHECK


Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>OPERATION CHECK


WIRING DIAGRAM

A475454E01
3.219,5.74 4.813,6.219 1.594,0.479 10 false Certification ECU (Smart Key ECU Assembly) 6.021,4.719 7.094,5.156 1.073,0.438 10 false Engine Stop and Start ECU 6.5,6.063 7,6.333 0.5,0.271 10 false ECM 6.146,6.063 6.646,6.333 0.5,0.271 10 false G184 2.885,1.5 3.438,1.708 0.552,0.208 10 false IG2 0.438,0.469 0.938,0.667 0.5,0.198 10 false 70A FL 0.406,5.479 1.031,5.729 0.625,0.25 10 false 250A FL 2.365,0.458 2.99,0.792 0.625,0.333 10 false EFI-MAIN NO. 1 2.24,5.479 2.792,5.688 0.552,0.208 10 false SMART 5.875,0.302 6.375,0.573 0.5,0.271 10 false G313 6.292,3.969 6.792,4.24 0.5,0.271 10 false IG2 6,3.75 6.25,3.958 0.25,0.208 10 false 18 6.042,5.542 6.292,5.75 0.25,0.208 10 false 14 5.885,3.969 6.385,4.24 0.5,0.271 10 false G314 1.229,1.938 1.646,2.208 0.417,0.271 10 false 1V 4.729,0.729 5.146,1 0.417,0.271 10 false 1V 2.948,3.958 3.365,4.229 0.417,0.271 10 false 2O 1.271,0.302 1.688,0.573 0.417,0.271 10 false 1S 1.281,0.083 1.531,0.292 0.25,0.208 10 false 1 4.865,0.51 5.115,0.74 0.25,0.229 10 false 7 1.24,1.708 1.49,1.917 0.25,0.208 10 false 1 4.854,0.094 5.104,0.302 0.25,0.208 10 false 6 4.74,0.302 5.156,0.573 0.417,0.271 10 false 1V 4.583,5.313 5,5.583 0.417,0.271 10 false G213 1.656,4.115 2.323,4.396 0.667,0.281 10 false S&S IG2 2.25,2.938 4.208,3.365 1.958,0.427 10 false NO. 1 Integration Relay 0.521,6.115 1.594,6.313 1.073,0.198 10 false Battery 6.292,5.667 6.906,5.865 0.615,0.198 10 false MREL 3.448,0.958 4.531,1.208 1.083,0.25 10 false EFI MAIN NO. 1 3.781,2.594 4.333,2.802 0.552,0.208 10 false IG2 5.167,0.438 5.802,0.781 0.635,0.344 10 false EFI-MAIN NO. 3 6.292,0.292 6.604,0.49 0.313,0.198 10 false +B 1.229,2.344 1.542,2.542 0.313,0.198 10 false 1W 1.24,2.146 1.396,2.344 0.156,0.198 10 false 4 4.74,2.344 5.052,2.542 0.313,0.198 10 false 1V 4.865,2.125 5.021,2.323 0.156,0.198 10 false 2 0.833,3.958 1.146,4.156 0.313,0.198 10 false 2M 3.01,3.76 3.323,3.958 0.313,0.198 10 false 55 2.927,5.323 3.344,5.594 0.417,0.271 10 false G215 3.354,5.313 3.667,5.51 0.313,0.198 10 false +B 4.198,5.302 4.813,5.5 0.615,0.198 10 false IG1D 3.063,5.125 3.302,5.313 0.24,0.188 10 false 10 4.646,5.115 4.802,5.313 0.156,0.198 10 false 3 1.5,5.479 2.271,5.677 0.771,0.198 10 false J/B-B 6.052,0.104 6.208,0.302 0.156,0.198 10 false 1 0.771,4.583 6.885,4.781 6.115,0.198 10 false Instrument Panel Junction Block Assembly 0.813,3.76 0.969,3.958 0.156,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU, airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU assembly, perform learning of the external backup boost converter (eco run vehicle converter assembly).

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When the engine stop and start ECU or electromagnetic oil pump is replaced, check the electromagnetic oil pump.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION



HINT:
·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA

·

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.READ VALUE USING GTS (IG SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / IG Switch.


e.

According to the display on the GTS, read the Data List.

Result:
Tester Display Result Proceed to
IG Switch ON A
OFF B




A

B

2.CHECK ENGINE STOP AND START ECU (IG2 TERMINAL VOLTAGE)
2.CHECK ENGINE STOP AND START ECU (IG2 TERMINAL VOLTAGE)
A456121C46
4.677,0.083 5.063,0.354 0.385,0.271 5.042,1.031 5.281,1.5 true 0.656,0.104 0.969,0.302 0.313,0.198 10 false *a 5.219,1.542 5.833,1.74 0.615,0.198 10 false IG2 4.708,0.156 5.323,0.354 0.615,0.198 10 false G314
*a Component with harness connected
(Engine Stop and Start ECU)
- -


a.

Turn the engine switch on (IG).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G314-18 (IG2) - Body ground Engine switch on (IG) 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE STOP AND START ECU (+B TERMINAL VOLTAGE)

NG

5.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
3.CHECK ENGINE STOP AND START ECU (+B TERMINAL VOLTAGE)
A456121C47
3.26,0.094 3.646,0.365 0.385,0.271 4.063,0.854 4.146,1.458 true 0.865,0.135 1.177,0.333 0.313,0.198 10 false *a 4.073,1.5 4.688,1.698 0.615,0.198 10 false +B 3.302,0.156 3.917,0.354 0.615,0.198 10 false G313
*a Component with harness connected
(Engine Stop and Start ECU)
- -


a.

Turn the engine switch on (IG).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G313-1 (+B) - Body ground Engine switch on (IG) 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - NO. 1 INTEGRATION RELAY)
4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - NO. 1 INTEGRATION RELAY)
a.

Disconnect the engine stop and start ECU connector.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G313-1 (+B) - 1V-6 Always Below 1 Ω
G313-1 (+B) or 1V-6 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the engine stop and start ECU connector.


b.

Disconnect the instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G314-18 (IG2) - 2O-55 Always Below 1 Ω
G314-18 (IG2) or 2O-55 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - NO. 1 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - NO. 1 INTEGRATION RELAY)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Disconnect the 2M and 2O instrument panel junction block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2M-2 - 2O-55 Always Below 1 Ω
2M-2 - 1V-1 Always Below 1 Ω
2M-2 or 2O-55 - Body ground and other terminals Always 10 kΩ or higher
2M-2 or 1V-1 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR