Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2020.08
RM27T0E _51 Engine / Hybrid System _091546 STOP AND START _0437376 STOP AND START SYSTEM J

STOP AND START  STOP AND START SYSTEM  Backup Boost Converter Circuit  


DESCRIPTION

A backup boost converter is built into the engine stop and start ECU. The backup boost converter helps maintain the power source voltage when the engine is restarted by stop and start control.

This prevents various functions such as the audio and visual system from malfunctioning if the power source voltage drops due to the battery voltage dropping when the engine is restarted by stop and start control.

If any DTCs are output, troubleshoot the DTCs first.

HINT:

A relay function and fuse function are provided in the backup boost converter.

If there is a malfunction in any of the electrical system circuits connected to the backup boost converter, the fuse and relay functions shut off the malfunctioning circuit to protect other circuits (remains shut off until next trip).

When the electrical system circuit is shut off, power to the circuit is cut off, causing any systems connected to the circuit to be disabled.

The fuse function is reset* when the engine switch is turned off. If the malfunction still exists in the electrical system circuit that has been shut off by the relay function, it will be shut off again by the relay and fuse functions the next time the engine switch is turned on (IG).

*: A semiconductor fuse self resets according to electric signal.

The backup boost converter supplies power to:
·

CAN communication system

·

Blind Spot Monitor System

·

Tire Pressure Warning System

·

Power Steering System

·

Audio and Visual System

·

Navigation System

·

Meter / Gauge System

·

Vehicle Stability Control System

·

Dynamic Radar Cruise Control System

·

Pre-Collision System

·

Panoramic View Monitor System

·

Air Conditioning System



CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and total number of engine starts and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU, airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When the engine stop and start ECU or electromagnetic oil pump is replaced, check the electromagnetic oil pump.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION



PROCEDURE

1.CHECK PROBLEM SYMPTOMS
a.

Determine the trouble area by referring to the table below.

Effect on Vehicle Trouble Area/Cause Fail-safe DTC Output Stop and start cancel indicator light Symptom Proceed to
When the engine is restarted by stop and start control, the following symptoms may occur.
·

The audio and visual system is reset

·

The combination meter assembly fades out

·

Air conditioning system cannot be operated


Backup boost converter internal malfunction
·

Internal power source malfunction

·

Internal power source overvoltage

·

Duty error

·

Communication cycle error


Stop and start control prohibited P323A00
P323AA2
P323B29
P323B38
Blinks Converter output voltage cannot be boosted when the engine is restarted A
Battery voltage drop
Systems on the converter output side do not operate
B41 terminal: None of the following will operate
·

Parking assist ECU

·

Tire pressure warning ECU and receiver


B42 terminal: None of the following will operate
·

Radio receiver assembly

·

Radio and display receiver assembly


B43 terminal: None of the following will operate
·

Navigation ECU

·

Integration Control and Panel Assembly


IG41 terminal: None of the following will operate
·

Network gateway ECU

·

Blind spot monitor sensor LH

·

Blind spot monitor sensor RH

·

Tire pressure warning ECU and receiver

·

Millimeter wave radar sensor assembly

·

Parking assist ECU

·

Air conditioning control assembly


Overcurrent applied to an output terminal (output terminal relay circuit is shutoff) Stop and start control is prohibited
(Connected ECUs or sensors may detect power source malfunction DTCs)
P323A19 Blinks Systems do not operate as power supply from the converter is cut off A
Systems do not operate
(Due to converter input side malfunction)
IG1 terminal: None of the following operate
·

Network gateway ECU

·

Blind spot monitor sensor LH

·

Blind spot monitor sensor RH

·

Tire pressure warning ECU and receiver

·

Millimeter wave radar sensor assembly

·

Parking assist ECU

·

Air conditioning control assembly

·

Steering sensor

·

Skid control ECU (brake actuator assembly)

·

Integration control and panel assembly


IG2 terminal: The combination meter assembly will not function
ACC terminal: None of the following operate
·

Radio receiver assembly

·

Radio and display receiver assembly

·

Parking assist ECU

·

Integration control and panel assembly


Converter input circuit malfunction
·

Open or short to GND in IG1 circuit

·

Open or short to GND in IG2 circuit

·

Open or short to GND in ACC circuit


Stop and start control prohibited - Does not blink (Blinks when communication error DTCs are stored) Systems do not operate as power supply from the converter is cut off B
Systems on the converter output side do not operate
(varies depending on the malfunctioning relay circuit the converter detected)
AC41 terminal: The combination meter assembly will not function
·

Radio receiver assembly

·

Radio and display receiver assembly

·

Parking assist ECU

·

Integration control and panel assembly


IG12 terminal: The combination meter assembly will not function
IG31 terminal: None of the following operate
·

Steering sensor

·

Skid control ECU (Brake actuator assembly)

·

Integration control and panel assembly


IG41 terminal: None of the following operate
·

Network gateway ECU

·

Blind spot monitor sensor LH

·

Blind spot monitor sensor RH

·

Tire pressure warning ECU and receiver

·

Millimeter wave radar sensor assembly

·

Parking assist ECU

·

Air conditioning control assembly


B42 terminal: None of the following operate
·

Radio receiver assembly

·

Radio and display receiver assembly


Malfunction in circuits the converter supplies power to
(between the converter and ECUs or sensors)
·

Open or short in the combination meter assembly circuit


Related systems do not operate as the relay circuit in the converter is turned off - Does not blink (Blinks when communication error DTCs are stored) Systems do not operate as power supply from the converter is cut off B
All of the following systems do not operate
·

CAN communication system

·

Blind Spot Monitor System

·

Tire Pressure Warning System

·

Power Steering System

·

Audio and Visual System

·

Navigation System

·

Meter / Gauge System

·

Vehicle Stability Control System

·

Dynamic Radar Cruise Control System

·

Pre-Collision System

·

Panoramic View Monitor System

·

Air Conditioning System


·

Open in BBC fuse circuit

·

Short in converter circuit

·

Backup boost converter malfunction


Stop and start control prohibited P061519 Does not blink (Due to disabled meter/gauge system) All systems that the converter supplies power to do not operate (see circuit diagram) A
P30DF62
P30EF4B
P323A00
P323A16
P323AA2
P323B29
P323B38
The audio and visual system does not function
(until the engine switch is turned off)
Excessive audio volume
Data List item "State of BBC" displays "BBC Overcurrent" while the circuit is protected
The relay circuit in the converter is turned off to cut off power supply to the navigation system (Returns to normal when the engine switch is turned off) - Does not blink If overcurrent is detected in the navigation system, system operation is disabled while the engine switch is on (IG)
(Returns to normal when the engine switch is turned off)
C
The external backup boost converter (eco run vehicle converter assembly) output side system does not operate
·

Navigation system


·

Open in BBC fuse circuit

·

Malfunction in circuits the converter supplies power to

·

External backup boost converter (eco run vehicle converter assembly) malfunction


- - Does not blink All systems that the converter supplies power to do not operate (see circuit diagram) D
The audio and visual system cannot be turned off (short between AC41 and +B)
The combination meter assembly cannot be turned off (short between IG12 and +B)
Communication error DTCs may be stored due to short between IG31 and +B
HINT:

Varies depending on the number of times an open occurs in the +B circuit


Converter circuit malfunction
·

Short between AC41 and +B

·

Short between IG31 and +B

·

Short between IG12 and +B


- - Does not blink The converter cannot shut off power source when the engine switch is turned off B
Engine switch does not turn to ACC (short between ACC and +B)
Engine switch does not turn off (short between IG1 or IG2 and +B)
Engine stop and start ECU power source circuit malfunction
·

Short between ACC and +B

·

Short between IG1 and +B

·

Short between IG2 and +B


- - Does not blink
·

Engine switch does not turn to ACC

·

Engine switch does not turn off


B


Result:
Proceed to
A
B
C
D



A

B

2.CHECK ENGINE STOP AND START ECU (POWER SOURCE CIRCUIT)

C

5.CHECK AUDIO AND VISUAL SYSTEM

D

7.CHECK HARNESS AND CONNECTOR (BIN TERMINAL POWER SOURCE CIRCUIT)
2.CHECK ENGINE STOP AND START ECU (POWER SOURCE CIRCUIT)
a.
A346343C18
1.458,0.354 1.906,0.573 0.448,0.219 1.5,2.479 1.948,2.698 0.448,0.219 0.979,1.229 0.531,1.24 true 1,1.583 0.552,1.594 true 1.563,3.76 1.573,4.188 true 2.052,3.74 2.406,4.167 true 1.417,3.75 1.073,4.177 true 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 1.51,0.385 1.969,0.583 0.458,0.198 10 false G312 0.167,1.156 0.573,1.385 0.406,0.229 10 false BIN2 0.177,1.521 0.583,1.75 0.406,0.229 10 false BIN1 1.552,2.51 2.01,2.708 0.458,0.198 10 false G314 1.438,4.229 1.896,4.427 0.458,0.198 10 false ACC 2.333,4.24 2.792,4.438 0.458,0.198 10 false IG1 0.917,4.219 1.375,4.417 0.458,0.198 10 false IG2
*a Front view of wire harness connector:
(to Engine Stop and Start ECU)


Disconnect the engine stop and start ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G312-1 (BIN2) - Body ground Always 9.5 to 14 V
G312-3 (BIN1) - Body ground Always 9.5 to 14 V



c.

Turn the engine switch ACC.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G314-19 (ACC) - Body ground Engine switch ACC 9.5 to 14 V



e.

Turn the engine switch on (IG).


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G314-21 (IG1) - Body ground Engine switch on (IG) 9.5 to 14 V
G314-18 (IG2) - Body ground Engine switch on (IG) 9.5 to 14 V



g.

Turn the engine switch off.


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G314-21 (IG1) - Body ground Engine switch off 0 to 1 V
G314-19 (ACC) - Body ground Engine switch off 0 to 1 V
G314-18 (IG2) - Body ground Engine switch off 0 to 1 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)
a.

Disconnect the connector from the corresponding system ECU/sensor.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Network Gateway ECU
Tester Connection Condition Specified Condition
G314-3 (IG41) - G229-11 (IG1) Always Below 1 Ω
G314-3 (IG41) - Body ground Always 10 kΩ or higher
G229-11 (IG1) - Body ground Always 10 kΩ or higher

Blind Spot Monitor Sensor LH*1
Tester Connection Condition Specified Condition
G314-3 (IG41) - R42-5 (BLB) Always Below 1 Ω
G314-3 (IG41) - Body ground Always 10 kΩ or higher
R42-5 (BLB) - Body ground Always 10 kΩ or higher

Blind Spot Monitor Sensor RH*1
Tester Connection Condition Specified Condition
G314-3 (IG41) - R43-5 (BRB) Always Below 1 Ω
G314-3 (IG41) - Body ground Always 10 kΩ or higher
R43-5 (BRB) - Body ground Always 10 kΩ or higher

Tire Pressure Warning ECU and Receiver*2
Tester Connection Condition Specified Condition
G314-2 (B41) - R41-7 (+B) Always Below 1 Ω
G314-3 (IG41) - R41-1 (IG) Always Below 1 Ω
G314-2 (B41) - Body ground Always 10 kΩ or higher
R41-7 (+B) - Body ground Always 10 kΩ or higher
G314-3 (IG41) - Body ground Always 10 kΩ or higher
R41-1 (IG) - Body ground Always 10 kΩ or higher

Millimeter Wave Radar Sensor Assembly*3
Tester Connection Condition Specified Condition
G314-3 (IG41) - A100-8 (IGB) Always Below 1 Ω
G314-3 (IG41) - Body ground Always 10 kΩ or higher
A100-8 (IGB) - Body ground Always 10 kΩ or higher

Parking Assist ECU*4
Tester Connection Condition Specified Condition
G314-2 (B41) - I6-1 (+B) Always Below 1 Ω
G314-3 (IG41) - I6-8 (IG) Always Below 1 Ω
G314-24 (AC41) - I6-9 (ACC) Always Below 1 Ω
G314-2 (B41) - Body ground Always 10 kΩ or higher
I6-1 (+B) - Body ground Always 10 kΩ or higher
G314-3 (IG41) - Body ground Always 10 kΩ or higher
I6-8 (IG) - Body ground Always 10 kΩ or higher
G314-24 (AC41) - Body ground Always 10 kΩ or higher
I6-9 (ACC) - Body ground Always 10 kΩ or higher

Air Conditioning Control Assembly*5
Tester Connection Condition Specified Condition
G314-3 (IG41) - T3-5 (IG) Always Below 1 Ω
G314-3 (IG41) - Body ground Always 10 kΩ or higher
T3-5 (IG) - Body ground Always 10 kΩ or higher

Air Conditioning Control Assembly*6
Tester Connection Condition Specified Condition
G314-3 (IG41) - T7-1 (IG) Always Below 1 Ω
G314-3 (IG41) - T7-9 (IG) Always Below 1 Ω
G314-3 (IG41) - Body ground Always 10 kΩ or higher
T7-5 (IG) - Body ground Always 10 kΩ or higher
T7-9 (IG) - Body ground Always 10 kΩ or higher

Steering Sensor
Tester Connection Condition Specified Condition
G314-1 (IG31) - G205-4 (IG) Always Below 1 Ω
G314-1 (IG31) - Body ground Always 10 kΩ or higher
G205-4 (IG) - Body ground Always 10 kΩ or higher

Skid Control ECU (Brake Actuator Assembly)
Tester Connection Condition Specified Condition
G314-1 (IG31) - A7-46 (IG1) Always Below 1 Ω
G314-1 (IG31) - Body ground Always 10 kΩ or higher
A7-46 (IG1) - Body ground Always 10 kΩ or higher

Integration Control and Panel Assembly
Tester Connection Condition Specified Condition
G314-11 (B43) - G23-1 (+B) Always Below 1 Ω
G314-1 (IG31) - G23-5 (IG+) Always Below 1 Ω
G314-24 (AC41) - G23-6 (ACC) Always Below 1 Ω
G314-11 (B43) - Body ground Always 10 kΩ or higher
G23-1 (+B) - Body ground Always 10 kΩ or higher
G314-1 (IG31) - Body ground Always 10 kΩ or higher
G23-5 (IG+) - Body ground Always 10 kΩ or higher
G314-24 (AC41) - Body ground Always 10 kΩ or higher
G23-6 (ACC) - Body ground Always 10 kΩ or higher

Combination Meter Assembly
Tester Connection Condition Specified Condition
G314-10 (IG12) - G304-22 (IG+) Always Below 1 Ω
G314-10 (IG12) - Body ground Always 10 kΩ or higher
G304-22 (IG+) - Body ground Always 10 kΩ or higher

Radio Receiver Assembly*7
Tester Connection Condition Specified Condition
G314-12 (B42) - H64-4 (+B) Always Below 1 Ω
G314-24 (AC41) - H46-3 (ACC1) Always Below 1 Ω
G314-12 (B42) - Body ground Always 10 kΩ or higher
H64-4 (+B) - Body ground Always 10 kΩ or higher
G314-24 (AC41) - Body ground Always 10 kΩ or higher
H46-3 (ACC1) - Body ground Always 10 kΩ or higher

Radio and Display Receiver Assembly*8
Tester Connection Condition Specified Condition
G314-12 (B42) - H92-4 (+B1) Always Below 1 Ω
G314-24 (AC41) - H92-15 (ACC1) Always Below 1 Ω
G314-12 (B42) - Body ground Always 10 kΩ or higher
H92-4 (+B1) - Body ground Always 10 kΩ or higher
G314-24 (AC41) - Body ground Always 10 kΩ or higher
H92-15 (ACC1) - Body ground Always 10 kΩ or higher


Navigation ECU*9
Tester Connection Condition Specified Condition
G314-11 (B43) - H96-10 (+B) Always Below 1 Ω
G314-11 (B43) - Body ground Always 10 kΩ or higher
H96-10 (IG1) - Body ground Always 10 kΩ or higher

*1: w/ Blind Spot Monitor System

*2: w/ Tire Pressure Warning System

*3: w/ Dynamic Radar Cruise Control System

*4: w/ Panoramic View Monitor System

*5: w/o Rear seat heater

*6: w/ Rear seat heater

*7: for Radio Receiver Type

*8: for Radio and Display Receiver Type

*9: w/ Navigation System



Result:
Proceed to
OK
NG



OK

4.CHECK ENGINE STOP AND START ECU (EACH ECU OR SENSOR POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK ENGINE STOP AND START ECU (EACH ECU OR SENSOR POWER SOURCE CIRCUIT)
a.

Disconnect the connector from the corresponding system ECU/sensor.


b.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage at the corresponding terminals.


Standard Voltage:
Tester Connection Condition Specified Condition
R41-7 (+B)*1 - Body ground Always 10.5 to 16 V
I6-1 (+B)*2 - Body ground Always 10.5 to 16 V
H46-4 (+B1)*3 - Body ground Always 10.5 to 16 V
H92-4 (+B1)*4 - Body ground Always 10.5 to 16 V
H96-10 (+B)*5 - Body ground Always 10.5 to 16 V
G23-1 (+B) - Body ground Always 10.5 to 16 V


*1: w/ Tire Pressure Warning System

*2: w/ Panoramic View Monitor System

*3: for Radio Receiver Type

*4: for Radio and Display Receiver Type

*5: w/ Navigation System



c.

Turn the engine switch ACC.


d.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage at the corresponding terminals.


Standard Voltage:
Tester Connection Switch Condition Specified Condition
H46-3 (ACC1)*1 - Body ground Engine switch ACC 10.5 to 16 V
H92-15 (ACC1)*2 - Body ground Engine switch ACC 10.5 to 16 V
I6-9 (ACC)*3 - Body ground Engine switch ACC 10.5 to 16 V
G23-6 (ACC) - Body ground Engine switch ACC 10.5 to 16 V


*1: for Radio Receiver Type

*2: for Radio and Display Receiver Type

*3: w/ Panoramic View Monitor System



e.

Turn the engine switch on (IG).


f.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage at the corresponding terminals.


Standard Voltage:
Tester Connection Switch Condition Specified Condition
G229-11 (IG1) - Body ground Engine switch on (IG) 10.5 to 16 V
R42-5 (BLB)*1 - Body ground Engine switch on (IG) 10.5 to 16 V
R43-5 (BRB)*1 - Body ground Engine switch on (IG) 10.5 to 16 V
R41-1 (IG)*2 - Body ground Engine switch on (IG) 10.5 to 16 V
A100-8 (IGB)*3 - Body ground Engine switch on (IG) 10.5 to 16 V
I6-8 (IG)*4 - Body ground Engine switch on (IG) 10.5 to 16 V
T3-5 (IG)*5 - Body ground Engine switch on (IG) 10.5 to 16 V
T7-1 (IG)*6 - Body ground Engine switch on (IG) 10.5 to 16 V
T7-9 (IG)*6 - Body ground Engine switch on (IG) 10.5 to 16 V
G205-4 (IG) - Body ground Engine switch on (IG) 10.5 to 16 V
A7-46 (IG1) - Body ground Engine switch on (IG) 10.5 to 16 V
G23-5 (IG+) - Body ground Engine switch on (IG) 10.5 to 16 V


*1: w/ Blind Spot Monitor System

*2: w/ Tire Pressure Warning System

*3: w/ Dynamic Radar Cruise Control System

*4: w/ Panoramic View Monitor System

*5: w/o Rear seat heater

*6: w/ Rear seat heater



Result:
Proceed to
OK
NG



OK

CHECK POWER SOURCE CIRCUIT (POWER SOURCE CIRCUIT OF RELATED SYSTEM)

NG

5.CHECK AUDIO AND VISUAL SYSTEM
a.

Turn the engine switch off and wait for 1 minute.


b.

Turn the engine switch on (IG).


c.

Lower the audio volume.


d.

Check if the audio and visual system operates normally.

OK:

Audio and visual system operates normally.



Result:
Proceed to
OK
NG



OK

END

NG

6.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - RADIO RECEIVER ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - RADIO RECEIVER ASSEMBLY)
a.

Disconnect the engine stop and start ECU connector.


b.

Disconnect the radio receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G314-12 (B42) - Body ground Always 10 kΩ or higher
G314-24 (AC41) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (BIN TERMINAL POWER SOURCE CIRCUIT)
A331558C56
1.5,0.167 1.917,0.417 0.417,0.25 2.031,1.885 2.031,1.406 true 1.948,1.917 2.406,2.115 0.458,0.198 10 false BIN 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.552,0.208 1.896,0.448 0.344,0.24 10 false A129
*a Front view of wire harness connector
(to External Backup Boost Converter (Eco Run Vehicle Converter Assembly))


a.

Disconnect the external backup boost converter (eco run vehicle converter assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A129-11 (BIN) - Body ground Always 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (ACC TERMINAL POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY) - BATTERY)

8.CHECK HARNESS AND CONNECTOR (ACC TERMINAL POWER SOURCE CIRCUIT)
A331558C57
1.479,0.167 1.896,0.417 0.417,0.25 1.146,1.875 1.542,1.198 true 1,1.927 1.458,2.125 0.458,0.198 10 false ACC 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.531,0.208 1.896,0.438 0.365,0.229 10 false A129
*a Front view of wire harness connector
(to External Backup Boost Converter (Eco Run Vehicle Converter Assembly))


a.

Disconnect the external backup boost converter (eco run vehicle converter assembly) connector.


b.

Turn the engine switch ACC.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A129-3 (ACC) - Body ground Engine switch ACC 9.5 to 14 V



d.

Turn the engine switch off.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A129-3 (ACC) - Body ground Engine switch off 0 to 1 V



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY) - BODY GROUND)

NG

12.CHECK HARNESS AND CONNECTOR (EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
9.CHECK HARNESS AND CONNECTOR (EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY) - BODY GROUND)
a.

Disconnect the external backup boost converter (eco run vehicle converter assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A129-6 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY) - STEREO COMPONENT AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY) - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the external backup boost converter (eco run vehicle converter assembly) connector.


b.

Disconnect the stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for JBL Type:
Tester Connection Condition Specified Condition
A129-5 (BO1) - H64-1 (+B) Always Below 1 Ω
A129-5 (BO1) - H64-3 (+B2) Always Below 1 Ω
A129-12 (ACO) - H105-12 (ACC) Always Below 1 Ω
A129-5 (BO1)or H64-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
A129-5 (BO1)or H64-3 (+B2) - Body ground and other terminals Always 10 kΩ or higher
A129-12 (ACO)or H105-12 (ACC) - Body ground and other terminals Always 10 kΩ or higher


Standard Resistance:
Except JBL Type:
Tester Connection Condition Specified Condition
A129-5 (BO1) - H67-1 (+B) Always Below 1 Ω
A129-5 (BO1) - H67-16 (+B2) Always Below 1 Ω
A129-12 (ACO) - H105-12 (ACC) Always Below 1 Ω
A129-5 (BO1)or H67-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
A129-5 (BO1)or H67-16 (+B2) - Body ground and other terminals Always 10 kΩ or higher
A129-12 (ACO)or H105-12 (ACC) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE CIRCUIT)
a.

Disconnect the stereo component amplifier assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for JBL Type:
Tester Connection Condition Specified Condition
H64-1 (+B) - Body ground Always 10.5 to 16 V
H64-3 (+B2) - Body ground Always 10.5 to 16 V


Standard Voltage:
Except JBL Type:
Tester Connection Condition Specified Condition
H67-1 (+B) - Body ground Always 10.5 to 16 V
H67-16 (+B2) - Body ground Always 10.5 to 16 V



c.

Turn the engine switch ACC.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H105-12 (ACC) - Body ground Engine switch ACC 10.5 to 16 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY)

12.CHECK HARNESS AND CONNECTOR (EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the external backup boost converter (eco run vehicle converter assembly) connector.


b.

Disconnect the instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A129-3 (ACC) - 2O-50 Always Below 1 Ω
A129-3 (ACC) or 2O-50 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR