Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2020.08
RM27T0E _51 Engine / Hybrid System _091546 STOP AND START _0437376 STOP AND START SYSTEM J

STOP AND START  STOP AND START SYSTEM  STA Signal Circuit  


DESCRIPTION

While the engine is being cranked, a starter operation request signal is sent to terminal STA of the ECM.

HINT:

If there is an open in the STA circuit of the ECM, stop and start control will be prohibited after the third time the engine is started by stop and start control.

·

Stop and start control will be prohibited until the engine switch is turned off.

·

The MIL will not illuminate.

·

If there is an open in the STA circuit of the ECM, the engine can still be started using the engine switch, as the ECM also receives the starter operation request signal from the engine stop and start ECU via CAN communication. (Stop and start control is prohibited as the reliability of the signal sent via CAN communication cannot be assured while the voltage drops during operation of the starter assembly.)



A347476E01
2.667,0.51 4.604,0.75 1.938,0.24 10 false Starter operation request signal 4.26,1.615 5.823,1.833 1.563,0.219 10 false Starter operation request 4.26,2.094 5.823,2.313 1.563,0.219 10 false Starter operation request 5.958,2.51 7.01,2.865 1.052,0.354 10 false Engine Stop and Start ECU 2.385,2.115 3,2.313 0.615,0.198 10 false Open 0.583,2.51 1.042,2.708 0.458,0.198 10 false ECM 0.781,1.875 1.24,2.073 0.458,0.198 10 false STA 6.146,1.885 6.604,2.083 0.458,0.198 10 false STA2 6.156,0.833 6.615,1.031 0.458,0.198 10 false CAN 0.75,0.823 1.208,1.021 0.458,0.198 10 false CAN 0.844,3.25 3.594,3.448 2.75,0.198 10 false from ST NO. 2 Fuse 0.833,4.74 3.896,4.938 3.063,0.198 10 false for Starter Assembly 3.885,4 5.115,4.198 1.229,0.198 10 false ST NO. 2 0.396,5.333 2.156,5.552 1.76,0.219 10 false : CAN Communication Line

WIRING DIAGRAM

A330989E17
5.427,0.625 5.885,0.823 0.458,0.198 10 false G314 5.51,0.427 5.823,0.625 0.313,0.198 10 false 13 5.438,1.021 5.896,1.219 0.458,0.198 10 false G314 5.51,0.833 5.823,1.031 0.313,0.198 10 false 14 5.865,0.656 6.479,0.854 0.615,0.198 10 false CANH 5.875,1.031 6.49,1.229 0.615,0.198 10 false CANL 1.271,0.646 1.885,0.844 0.615,0.198 10 false CANH 1.292,1.042 1.906,1.24 0.615,0.198 10 false CANL 1.792,0.438 2.104,0.635 0.313,0.198 10 false 17 1.802,0.844 2.115,1.042 0.313,0.198 10 false 28 1.375,1.5 1.833,1.698 0.458,0.198 10 false STA 5.521,1.292 5.833,1.49 0.313,0.198 10 false 23 5.885,1.5 6.344,1.698 0.458,0.198 10 false STA2 1.792,1.365 2.104,1.563 0.313,0.198 10 false 22 1.146,2.438 1.781,2.656 0.635,0.219 10 false ECM 0.781,2.281 1.24,2.479 0.458,0.198 10 false G184 2.281,3.063 3.354,3.26 1.073,0.198 10 false ST NO. 2 4.802,3.615 5.875,3.813 1.073,0.198 10 false ST NO. 2 4.417,3.208 4.573,3.406 0.156,0.198 10 false 2 4.073,3.99 4.229,4.188 0.156,0.198 10 false 3 4.427,3.99 4.583,4.188 0.156,0.198 10 false 1 4.063,3.208 4.219,3.406 0.156,0.198 10 false 5 0.938,4.771 1.646,4.979 0.708,0.208 10 false Battery 0.771,3.708 1.542,3.906 0.771,0.198 10 false 250A FL 4.75,5.594 5.979,5.792 1.229,0.198 10 false Starter Assembly 4.74,5.438 5.052,5.635 0.313,0.198 10 false D14 4.115,5.344 4.573,5.542 0.458,0.198 10 false SL2 4.063,5.052 4.219,5.25 0.156,0.198 10 false 2 0.771,6.208 3.01,6.406 2.24,0.198 10 false : CAN Communication Line 5.188,2.406 6.948,2.823 1.76,0.417 10 false Engine Stop and Start ECU 5.427,1.5 5.885,1.698 0.458,0.198 10 false G313

PROCEDURE

1.READ VALUE USING GTS (STARTER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Starter SW.


e.

Read the values displayed on the GTS when the engine switch is on (IG) and on (START).

OK:
Tester Display Condition Normal Condition
Starter SW Engine switch on (IG) OFF
Engine switch on (START) ON



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (ECM - ST NO. 2 RELAY)
2.CHECK HARNESS AND CONNECTOR (ECM - ST NO. 2 RELAY)
a.

Disconnect the engine stop and start ECU connector.


b.

Disconnect the ECM connector.


c.

Remove the ST NO. 2 relay from the engine room relay block and junction block assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G184-22 (STA) - ST NO. 2 relay terminal 2 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR