CHECK ECM (for 1GD-FTV)
As a waterproof connector is used for the ECM, voltage, resistance and waveform inspections cannot be performed. The voltage, resistance and waveform values are provided for reference only.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G185-13 (STP) - G185-5 (E1) | V - W-B | Stop light switch signal | Brake pedal depressed | 7.5 to 14 V |
| Brake pedal released | 0 to 1.5 V | |||
| G185-12 (ST1-) - G185-5 (E1) | B - W-B | Stop light switch signal | Ignition switch ON, brake pedal depressed | 0 to 1.5 V |
| Ignition switch ON, brake pedal released | 7.5 to 14 V | |||
| G185-26 (CCS) - G185-5 (E1) | B - W-B | Cruise control main switch circuit | Cruise control main switch (ON-OFF) off | 1 MΩ or higher |
| Cruise control main switch (ON-OFF) on | Below 2.5 Ω | |||
| +RES switch on | 228 to 252 Ω | |||
| -SET switch on | 599 to 661 Ω | |||
| CANCEL switch on | 1463 to 1617 Ω |
CHECK ECM (for 2TR-FE)
As a waterproof connector is used for the ECM, voltage, resistance and waveform inspections cannot be performed. The voltage, resistance and waveform values are provided for reference only.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G180-10 (STP) - C153-3 (E1) | V - W-B | Stop light switch signal | Brake pedal depressed | 7.5 to 14 V |
| Brake pedal released | 0 to 1.5 V | |||
| G180-11 (ST1-) - C153-3 (E1) | B - W-B | Stop light switch signal | Ignition switch ON, brake pedal depressed | 0 to 1.5 V |
| Ignition switch ON, brake pedal released | 7.5 to 14 V | |||
| G181-22 (CCS) - G181-21 (ECCS) | B - BR | Cruise control main switch circuit | Cruise control main switch (ON-OFF) off | 1 MΩ or higher |
| Cruise control main switch (ON-OFF) on | Below 2.5 Ω | |||
| +RES switch on | 228 to 252 Ω | |||
| -SET switch on | 599 to 661 Ω | |||
| CANCEL switch on | 1463 to 1617 Ω |
CHECK ECM (for 1GR-FE)
As a waterproof connector is used for the ECM, voltage, resistance and waveform inspections cannot be performed. The voltage, resistance and waveform values are provided for reference only.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G56-35 (STP) - C36-12 (E1) | V - BR | Stop light switch signal | Brake pedal depressed | 7.5 to 14 V |
| Brake pedal released | 0 to 1.5 V | |||
| G56-34 (ST1-) - C36-12 (E1) | B - BR | Stop light switch signal | Ignition switch ON, brake pedal depressed | 0 to 1.5 V |
| Ignition switch ON, brake pedal released | 7.5 to 14 V | |||
| G56-1 (CCS) - C36-12 (E1) | B - BR | Cruise control main switch circuit | Cruise control main switch (ON-OFF) off | 1 MΩ or higher |
| Cruise control main switch (ON-OFF) on | Below 2.5 Ω | |||
| +RES switch on | 228 to 252 Ω | |||
| -SET switch on | 599 to 661 Ω | |||
| CANCEL switch on | 1463 to 1617 Ω |
CHECK FORWARD RECOGNITION CAMERA
Turning the ignition switch to ON with connectors disconnected may cause DTCs to be stored. Make sure to clear the DTCs after inspection has been performed.
Do not apply excessive force to the forward recognition camera connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| W22-3 (LKSW) - W22-10 (GND) | V - W-B | Steering pad switch assembly signal (distance control signal) | Ignition switch ON, steering pad switch assembly (vehicle-to-vehicle distance control switch) on | Below 1 V |
| Ignition switch ON, steering pad switch assembly (vehicle-to-vehicle distance control switch) off | 4.75 to 5.25 V | |||
| W22-10 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| W22-7 (IGB) - W22-10 (GND) | G - W-B | Power source | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |