Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › from 2020.08
RM27T0E _58 Vehicle Interior _091549 PRE-COLLISION _0438246 PRE-COLLISION SYSTEM D

PRE-COLLISION  PRE-COLLISION SYSTEM  FREEZE FRAME DATA  


DESCRIPTION


a.

When a pre-collision system DTC is stored, the forward recognition camera stores the current vehicle (ECU or sensor) state as Freeze Frame Data.



CHECK FREEZE FRAME DATA


a.

According to the GTS display, select a DTC that stored freeze frame data.


b.

Read the freeze frame data recorded when the DTC was stored.

Body Electrical > Pre-Collision System
Tester Display Measurement Item / Range Normal Condition Diagnostic Note
Total Distance Traveled - - Not applicable
Total Distance Traveled - Unit - - Not applicable
PCS Function ON/OFF State Pre-collision system on/off status / ON or OFF ON: Pre-collision system on
OFF: Pre-collision system off
-
PBA Request Pre-collision brake assist operation status / Not PBA Request, PBA Standby Request, PBA Request Level 1, PBA Request Level 2 Not PBA Request: Pre-collision brake assist operation is not requested.
PBA Standby Request: Pre-collision brake assist weak assist is requested.
PBA Request Level 1: Pre-collision brake assist mild assist is requested.
PBA Request Level 2: Pre-collision brake assist strong assist is requested.
The value varies according to the possibility of a collision. The pre-collision brake assist request only indicates the status that the assist preparation is necessary. Whether or not the assist control is actually performed is dependent upon how the driver depresses the brake.
VGRS Activation Request - - This item is displayed on the GTS for vehicles without the VGRS system, but cannot be used.
Warning Brake Request - - Cannot be used
FPB Request PCS brake request to skid control ECU (pre-collision braking) / ON or OFF ON: Operating
OFF: Not operating
-
PB Request Pre-collision brake operation status / ON or OFF ON: Operating
OFF: Not operating
-
AVS Control Request AVS operation status / ON or OFF ON: Operating
OFF: Not operating
-
Prefill PCS brake operation preparation to skid control ECU / ON or OFF ON: Operating
OFF: Not operating
-
PBR Request PBR operation status / ON or OFF ON: Operating
OFF: Not operating
-
PBH Request PBH operation status / ON or OFF ON: Operating
OFF: Not operating
PBH: Pre-collision brake hold
PCS PBA Invalid Pre-collision brake assist function status / ON or OFF ON: Pre-collision brake assist function invalid
OFF: Pre-collision brake assist function valid
-
PCS Warning Buzzer Invalid PCS warning buzzer function status / ON or OFF ON: PCS warning buzzer function invalid
OFF: PCS warning buzzer function valid
-
PCS PB Invalid PCS brake function status / ON or OFF ON: PCS brake function invalid
OFF: PCS brake function valid
-
PCS Warning Display Request PCS warning message status / Not Request, PCS Warning Display 1 Request, PCS Warning Display 2 Request, PCS Warning Display 3 Request Not Request: Not displayed
PCS Warning Display 1 Request: Displayed
PCS Warning Display 2 Request: Not used
PCS Warning Display 3 Request: Not used
"BRAKE!" is displayed on multi-information display
PCS Warning Buzzer Request PCS warning buzzer (meter buzzer) status / ON or OFF ON: PCS warning buzzer sounding
OFF: PCS warning buzzer not sounding
-
PCS Function ON/OFF State Stored Storage condition of PCS ON/OFF condition when the PCS function is off and the ignition switch is turned from off to ON / Stored or Not Stored Stored: Pre-collision system maintains off
Not Stored: Pre-collision system always turns on
"PCS Function ON/OFF State Stored" is a customizable item which can be set using the GTS.
PCS Warning Timing State Stored 2 Storage condition of warning sensitivity setting when the PCS function is on and the ignition switch is turned from off to ON / Stored or Not Stored Stored: Sensitivity settings are maintained as previous value
Not Stored: Sensitivity is reset to default setting
"PCS Function ON/OFF State Stored 2" is a customizable item which can be set using the GTS.
PCS Warning Timing State Stored 3 Storage condition of warning sensitivity setting when the PCS function is off and the ignition switch is turned from off to ON / Stored or Not Stored Stored: Sensitivity settings are maintained as previous value
Not Stored: Sensitivity is reset to default setting
"PCS Function ON/OFF State Stored 3" is a customizable item which can be set using the GTS.
PCS Warning Timing State Stored 1 Storage condition of warning sensitivity setting when the PCS function is turned from off to on while the ignition switch is ON / Stored or Not Stored Stored: Sensitivity settings are maintained as previous value
Not Stored: Sensitivity is reset to default setting
"PCS Function ON/OFF State Stored 1" is a customizable item which can be set using the GTS.