READ DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Cruise Control / Data List.
Read the Data List according to the display on the GTS.
If any DTCs are output, the value for a measurement item may be incorrect.
If any DTCs are output, perform troubleshooting accordingly. After repair, confirm relevant values using Data List.
| Tester Display | Measurement Item / Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| CCS Vehicle Spd | Vehicle speed / Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Actual vehicle speed displayed | - |
| CCS Mem Vehicle Spd | Vehicle speed / Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Vehicle speed stored in memory | - |
| Throttle Opening Angle | Required throttle opening angle / 0.00 to 124.5 deg | Required throttle opening angle | - |
| Cruise Control | Cruise control / ON or OFF | ON: Cruise control set
OFF: Cruise control not set |
- |
| Cruise Main Switch Operation Condition | Cruise control switch status / ON or OFF | ON: Cruise control switch pushed
OFF: Cruise control switch not pushed |
- |
| Main SW M-CPU | Cruise control main switch (Main CPU) / ON or OFF | ON: Cruise control main switch on
OFF: Cruise control main switch off |
- |
| CCS Ready M-CPU | Cruise control system standby condition (Main CPU) / ON or OFF | ON: Cruise control main switch on
OFF: Cruise control main switch off |
- |
| CCS Indicator M-CPU | CRUISE main indicator (Main CPU) / ON or OFF | ON: CRUISE main indicator light on
OFF: CRUISE main indicator light off |
- |
| Cancel Switch | CANCEL switch signal / ON or OFF | ON: CANCEL switch on
OFF: CANCEL switch off |
- |
| SET/COAST Switch | -SET switch signal / ON or OFF | ON: -SET switch on
OFF: -SET switch off |
- |
| RES/ACC Switch | +RES switch signal / ON or OFF | ON: +RES switch on
OFF: +RES switch off |
- |
| Stop Light Switch 1 | Stop light switch signal / ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
| Stop Light Switch 2 | Stop light switch signal / ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
| Cruise Operation Status | Shift lever position signal / ON or OFF | ON: Shift lever in D
OFF: Shift lever not in D |
- |
| Brake Cancel Switch | Brake cancel signal /ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
PERFORM ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Active Test.
According to the display on the GTS, perform the Active Test.
The ignition switch must be turned to ON to proceed with the Active Test using the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Meter Display 1 | Multi-information display | OFF or All | - |