Home › Audio / Visual / Telematics › AUDIO / VIDEO › REAR SEAT ENTERTAINMENT SYSTEM › from 2020.08
RM27T0E _56 Audio / Visual / Telematics _053720 AUDIO / VIDEO _0260968 REAR SEAT ENTERTAINMENT SYSTEM J

AUDIO / VIDEO  REAR SEAT ENTERTAINMENT SYSTEM  Television Display Power Source Circuit  


DESCRIPTION

This is the power source circuit to operate the television display assembly.

WIRING DIAGRAM

E446273E02
5.208,2.021 5.667,2.219 0.458,0.198 10 false W14 5.229,2.208 7.042,2.458 1.813,0.25 10 false Television Display Assembly 4.094,0.969 5.094,1.177 1,0.208 10 false RAD NO.3*2 5.615,0.792 6.073,0.99 0.458,0.198 10 false +B 5.646,1.208 6.104,1.406 0.458,0.198 10 false ACC 5.615,1.698 6.073,1.896 0.458,0.198 10 false GND 5.417,0.688 5.875,0.885 0.458,0.198 10 false 1 5.406,1.104 5.865,1.302 0.458,0.198 10 false 2 5.354,1.552 5.813,1.75 0.458,0.198 10 false 17 4.26,1.396 4.875,1.615 0.615,0.219 10 false ACC*2 2.354,0.792 3.438,1.052 1.083,0.26 10 false from Battery*2 2.229,0.271 4.635,0.51 2.406,0.24 10 false from Engine Stop and Start ECU*1 2.156,1.24 3.396,1.583 1.24,0.344 10 false from ACC Relay*2 0.135,1.938 2.906,2.125 2.771,0.188 10 false *1: w/ Stop and Start System 0.125,2.271 2.896,2.458 2.771,0.188 10 false *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuse for circuits related to this system before performing procedure. (w/o Stop and Start System)


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY POWER SOURCE)
a.

Disconnect the television display assembly connector.


b.
E424905C07
1.438,0.135 1.833,0.396 0.396,0.26 1.156,1.344 1.313,1.76 1.313,1.76 1.448,1.76 true 0.865,1.125 0.458,1.729 0.458,1.729 0.292,1.729 true 1.01,1.073 0.635,0.51 0.635,0.51 0.469,0.51 true 0.198,0.094 0.354,0.271 0.156,0.177 10 false *a 1.521,1.656 1.885,1.927 0.365,0.271 10 false GND 0.083,1.646 0.333,1.833 0.25,0.188 10 false +B 0.135,0.427 0.698,0.698 0.563,0.271 10 false ACC 1.49,0.177 1.844,0.354 0.354,0.177 10 false W14
*a Front view of wire harness connector
(to Television Display Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W14-17 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

*1: w/o Stop and Start System

*2: w/ Stop and Start System

W14-1 (+B) - W14-17 (GND) Always 11 to 14 V*1
10.5 to 16 V*2
W14-2 (ACC) - W14-17 (GND) Ignition switch ACC 11 to 14 V*1
10.5 to 16 V*2



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR