82641
1.INSPECT NO. 1 INTEGRATION RELAY
| *a | Component without harness connected
(No. 1 Integration Relay) |
- | - |
The EDU relay, IG2 relay, EFI MAIN NO. 1 relay and EFI MAIN NO. 2 relay are built into the No. 1 integration relay.
Before performing the relay inspections for the relays of the No. 1 integration relay, inspect the EDU, IG2, EFI MAIN NO. 1 and EFI MAIN NO. 2 fuses.
Inspect the EDU relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1S-1 - 1U-2 | Battery voltage not applied to terminals 1U-3 and 1U-1 | 10 kΩ or higher |
| Battery voltage applied to terminals 1U-3 and 1U-1 | Below 1 Ω |
If the result is not as specified, replace the No. 1 integration relay.
Inspect the IG2 relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1S-1 - 1V-1 | Battery voltage not applied to terminals 1V-2 and 1W-4 | 10 kΩ or higher |
| Battery voltage applied to terminals 1V-2 and 1W-4 | Below 1 Ω |
If the result is not as specified, replace the No. 1 integration relay.
Inspect the EFI-MAIN NO. 1 relay.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1V-6 (voltmeter positive (+) lead) - Battery negative (-) terminal (voltmeter negative (-) lead) | Battery voltage not applied to terminals 1S-1 (battery positive (+)) and 1V-7 (battery negative (-)) | Below 1 V |
| Battery voltage applied to terminals 1S-1 (battery positive (+)) and 1V-7 (battery negative (-)) | 11 to 14 V |
If the result is not as specified, replace the No. 1 integration relay.
Inspect the EFI MAIN NO. 2 relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1S-1 - 1W-3 | Battery voltage not applied to terminals 1W-1 and 1W-4 | 10 kΩ or higher |
| Battery voltage applied to terminals 1W-1 and 1W-4 | Below 1 Ω |
If the result is not as specified, replace the No. 1 integration relay.
Inspect the NOx PM relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1S-1 - 1W-10 | Battery voltage not applied to terminals 1W-8 and 1W-4 | 10 kΩ or higher |
| Battery voltage applied to terminals 1W-8 and 1W-4 | Below 1 Ω |
If the result is not as specified, replace the No. 1 integration relay.
896B1A
2.INSPECT DCU RELAY (DCU)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage not applied to terminals 1 and 2 | 10 kΩ or higher |
| Battery voltage applied to terminals 1 and 2 | Below 1 Ω |
If the result is not as specified, replace the DCU relay.