Home › Vehicle Interior › HEATING / AIR CONDITIONING › HEATER SWITCH › from 2020.08
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261199 HEATER SWITCH G

HEATING / AIR CONDITIONING  HEATER SWITCH  INSPECTION  


PROCEDURE

Hide 87290 1.INSPECT HEATER SWITCH ASSEMBLY

a.

Check resistance.

i.
E377033C01
1.469,1.635 1.469,1.302 true 1.958,1.635 1.958,1.302 true 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1.417,1.635 1.729,1.833 0.313,0.198 10 false IG 1.906,1.635 2.219,1.833 0.313,0.198 10 false IN
*a Component without harness connected
(Heater Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (IG) - 2 (IN) Heater switch assembly off 10 kΩ or higher
Heater switch assembly on Below 1 Ω


If the result is not as specified, there may be a malfunction in the heater switch assembly.



b.

Check that the Indicator.

i.
E378184C01
1.958,4.125 1.958,3.625 true 1.625,4.125 1.625,3.625 true 2.448,1.073 1.865,1.073 true 1.906,4.135 2.219,4.333 0.313,0.198 10 false IN 1.583,4.135 1.896,4.333 0.313,0.198 10 false E 0.677,2.479 0.99,2.677 0.313,0.198 10 false *a 2.5,0.99 2.813,1.188 0.313,0.198 10 false *b
*a Component without harness connected
(Heater Switch Assembly)
*b Indicator


Apply battery voltage to the connector and check the Indicator.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2 (IN)
Battery negative (-) → 4 (E)
Indicator illuminates


If the result is not as specified, there may be a malfunction in the heater switch assembly.



c.

Check that the illumination.

i.
E377033C02
1.313,1.635 1.313,1.302 true 2.125,1.635 2.125,1.302 true 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1.24,1.667 1.604,1.865 0.365,0.198 10 false ILL+ 2.052,1.667 2.417,1.865 0.365,0.198 10 false ILL-
*a Component without harness connected
(Heater Switch Assembly)


Apply battery voltage to the connector and check the illumination.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 6 (ILL+)
Battery negative (-) → 1 (ILL-)
Heater switch assembly illuminates


If the result is not as specified, there may be a malfunction in the heater switch assembly.



Hide 84453 2.INSPECT IDLE UP SWITCH

E450274C01
1.323,1.865 1.323,1.302 true 2.406,1.219 2.917,1.219 true 2.052,1.865 2.052,1.302 true 0.5,1.229 1.01,1.229 true 0.135,0.115 0.313,0.292 0.177,0.177 10 false *a 1.208,1.896 1.49,2.083 0.281,0.188 10 false SW 2.021,1.896 2.198,2.083 0.177,0.188 10 false E 0.208,1.167 0.563,1.354 0.354,0.188 10 false ILL+ 2.969,1.146 3.323,1.333 0.354,0.188 10 false ILL-
*a Component without harness connected
(Idle Up Switch)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (SW) - 2 (E) Idle up switch off 10 kΩ or higher
Idle up switch on Below 1 Ω



b.

Apply battery voltage to the connector and check the LED illumination.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 6 (ILL+)
Battery negative (-) → 1 (ILL-)
LED illuminates


If the result is not as specified, there may be a malfunction in the idle up switch.