Home › Vehicle Exterior › LIGHTING (EXT) › STOP LIGHT SWITCH › from 2020.08
RM27T0E _59 Vehicle Exterior _053747 LIGHTING (EXT) _0261288 STOP LIGHT SWITCH G

LIGHTING (EXT)  STOP LIGHT SWITCH  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 84340 1.INSPECT STOP LIGHT SWITCH ASSEMBLY (for 5L-E)

a.

Disconnect the stop light switch assembly connector.


b.
E270964C43
1.5,0.198 1.938,0.479 0.438,0.281 2.198,1.219 2.74,1.146 true 1.271,1.198 0.688,1.021 true 1.708,1.333 1.583,1.771 true 0.083,0.167 0.396,0.438 0.313,0.271 10 false *a 1.406,1.813 1.875,2.083 0.469,0.271 10 false GND 2.792,1.031 3.052,1.302 0.26,0.271 10 false B 0.542,0.906 0.802,1.177 0.26,0.271 10 false B 1.615,0.24 2.073,0.438 0.458,0.198 10 false A85
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Measure the resistance and voltage on the wire harness side connector according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A85-3 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
A85-1 (B) - A85-3 (GND) Always 11 to 14 V
A85-5 (B) - A85-3 (GND) Ignition switch on (IG) 11 to 14 V


HINT:

If the result is not as specified, repair or replace the wire harness or connector.



c.

Reconnect the stop light switch assembly connector.


d.
E240777C26
1.521,0.177 1.958,0.417 0.438,0.24 1.948,1.719 1.75,1.052 true 1.542,1.073 1.177,1.531 true 1.917,1.073 2.26,1.51 true 0.115,0.125 0.354,0.354 0.24,0.229 10 false *a 1.844,1.76 2.292,1.99 0.448,0.229 10 false GND 1.063,1.479 1.271,1.708 0.208,0.229 10 false L 2.313,1.427 2.521,1.656 0.208,0.229 10 false L 1.615,0.208 2.073,0.406 0.458,0.198 10 false A85
*a Component with harness connected
(Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A85-2 (L) - A85-3 (GND) Ignition switch off, brake pedal not depressed Below 1 V
A85-2 (L) - A85-3 (GND) Ignition switch off, brake pedal depressed 11 to 14 V
A85-4 (L) - A85-3 (GND) Ignition switch on (IG), brake pedal not depressed 11 to 14 V
A85-4 (L) - A85-3 (GND) Ignition switch on (IG), brake pedal depressed Below 1 V


HINT:

If the result is not as specified, replace the stop light switch assembly.



Hide 84340 2.INSPECT STOP LIGHT SWITCH ASSEMBLY (except 5L-E)

a.

Disconnect the stop light switch assembly connector.


b.
E409581C81
1.5,0.115 1.896,0.375 0.396,0.26 1.135,1.833 1.271,1.354 true 2.219,1.844 2.083,1.365 true 2.49,1.865 2.292,1.354 true 1.573,0.156 2.031,0.354 0.458,0.198 10 false A99 0.969,1.865 1.385,2.094 0.417,0.229 10 false GND 2.208,1.885 2.427,2.104 0.219,0.219 10 false B 2.469,1.885 2.688,2.104 0.219,0.219 10 false B 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Measure the voltage and resistance on the wire harness side connector according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A99-7 (B) - A99-2 (GND) Always 11 to 14 V
A99-6 (B) - A99-2 (GND) Ignition switch on (IG) 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
A99-2 (GND) - Body ground Always Below 1 Ω


HINT:

If the result is not as specified, repair or replace the wire harness or connector.



c.

Reconnect the stop light switch assembly connector.


d.
E409580C34
1.51,0.083 1.927,0.385 0.417,0.302 2.313,1.24 2.896,0.938 true 2.135,1.26 2.49,1.875 true 1.927,1.271 2.281,1.885 true 1.24,1.865 1.698,1.292 true 0.865,1.948 1.49,1.281 true 0.094,0.083 0.406,0.24 0.313,0.156 10 false *a 1.594,0.135 2.052,0.333 0.458,0.198 10 false A99 2.969,0.833 3.313,1.073 0.344,0.24 10 false OUT 2.552,1.823 2.896,2.063 0.344,0.24 10 false GND 2.281,1.906 2.438,2.104 0.156,0.198 10 false L 1.063,1.896 1.406,2.135 0.344,0.24 10 false ACC 0.76,1.917 0.917,2.115 0.156,0.198 10 false L
*a Component with harness connected
(Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A99-1 (OUT) - A99-2 (GND) Brake pedal released 0 to 1.5 V
Brake pedal depressed 7.5 to 14 V
A99-3 (L) - A99-2 (GND) Brake pedal released 0 to 1.5 V
Brake pedal depressed 7.5 to 14 V
A99-4 (ACC) - A99-2 (GND) Always 11 to 14 V
A99-5 (L) - A99-2 (GND) Ignition switch on (IG), brake pedal released 7.5 to 14 V
Ignition switch on (IG), brake pedal depressed 0 to 1.5 V


HINT:

If the result is not as specified, replace the stop light switch assembly.