Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.08
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM U

1GR-FE ENGINE CONTROL  SFI SYSTEM  TERMINALS OF ECM  


CHECK ECM


U147632E03
0.615,0.542 0.99,0.771 0.375,0.229 10 false G55 1.656,0.542 2.031,0.771 0.375,0.229 10 false G56 3.135,0.542 3.51,0.771 0.375,0.229 10 false C34 4.188,0.542 4.563,0.771 0.375,0.229 10 false C35 5.229,0.542 5.604,0.771 0.375,0.229 10 false C36 6.292,0.542 6.667,0.771 0.375,0.229 10 false C37

a.

Measure the voltage of the ECM connectors.

HINT:

The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage for that pair of terminals, displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.


for Automatic Transmission
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G55-24 (BATT) - C36-12 (E1) L - BR Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
C36-6 (+BM) - C36-12 (E1) GR - BR Power source of throttle actuator Always 11 to 14 V
G55-21 (IGSW) - C36-12 (E1) W - BR Engine switch Engine switch on (IG) 11 to 14 V
G55-23 (+B) - C36-12 (E1) W - BR Power source of ECM Engine switch on (IG) 11 to 14 V
G55-22 (+B2) - C36-12 (E1) W - BR Power source of ECM Engine switch on (IG) 11 to 14 V
C34-31 (OC1+) - C34-32 (OC1-) G - L Camshaft timing oil control valve assembly (for Intake Side of Bank 1) Engine switch on (IG) Pulse generation (see waveform 1)
C34-33 (OC2+) - C34-34 (OC2-) W - R Camshaft timing oil control valve assembly (for Intake Side of Bank 2) Engine switch on (IG) Pulse generation
(see waveform 1)
C34-35 (OE1+) - C34-36 (OE1-) G - B Camshaft timing oil control valve assembly (for Exhaust Side of Bank 1) Engine switch on (IG) Pulse generation
(see waveform 1)
C34-30 (OE2+) - C34-24 (OE2-) W - L Camshaft timing oil control valve assembly (for Exhaust Side of Bank 2) Engine switch on (IG) Pulse generation
(see waveform 1)
G56-36 (MREL) - C36-12 (E1) V - BR EFI MAIN NO. 1 relay Engine switch on (IG) 11 to 14 V
C34-14 (VG) - C35-18 (E2G) W - B Mass air flow meter Idling, shift lever in P or N, A/C switch off 0.5 to 3.0 V
C35-17 (THA) - C36-4 (ETHW) Y - W-R Intake air temperature sensor Idling, intake air temperature 20°C (68°F) 0.5 to 3.4 V
C36-5 (THW) - C36-4 (ETHW) R-L - W-R Engine coolant temperature sensor Idling, engine coolant temperature 80°C (176°F) 0.2 to 1.0 V
C36-2 (VCTA) - C36-3 (ETA) L - P Power source for throttle position sensor (fixed voltage) Engine switch on (IG) 4.5 to 5.5 V
C36-1 (VTA1) - C36-3 (ETA) LG - P Throttle position sensor (for engine control) Engine switch on (IG),
throttle valve fully closed
0.5 to 1.1 V
Engine switch on (IG),
throttle valve fully open
3.3 to 4.9 V
C36-9 (VTA2) - C36-3 (ETA) Y - P Throttle position sensor (for sensor malfunction detection) Engine switch on (IG),
throttle valve fully closed
2.1 to 3.1 V
Engine switch on (IG),
throttle valve fully open
4.6 to 5.0 V
G55-2 (VPA) - G55-1 (EPA) L - P Accelerator pedal position sensor (for engine control) Engine switch on (IG),
accelerator pedal released
0.5 to 1.1 V
Engine switch on (IG),
accelerator pedal fully depressed
2.6 to 4.5 V
G56-5 (VPA2) - G56-4 (EPA2) GR - W Accelerator pedal position sensor (for sensor malfunction detection) Engine switch on (IG),
accelerator pedal released
1.2 to 2.0 V
Engine switch on (IG),
accelerator pedal fully depressed
3.4 to 4.75 V
G56-6 (VCPA) - G55-1 (EPA) LG - P Power source of accelerator pedal position sensor (for VPA) Engine switch on (IG) 4.5 to 5.5 V
G56-3 (VCP2) - G56-4 (EPA2) R - W Power source of accelerator pedal position sensor (for VPA2) Engine switch on (IG) 4.5 to 5.5 V
C37-17 (HA1A) - C37-16 (E04)
C37-12 (HA2A) - C37-11 (E05)
R-L - W-B
B-W - W-B
Air fuel ratio sensor heater Idling Below 3.0 V
Engine switch on (IG) 11 to 14 V
C35-7 (A1A+) - C36-12 (E1) R -BR Air fuel ratio sensor Engine switch on (IG) 3.3 V*
C35-8 (A1A-) - C36-12 (E1) G - BR Air fuel ratio sensor Engine switch on (IG) 3.0 V*
C35-1 (A2A+) - C36-12 (E1) B - BR Air fuel ratio sensor Engine switch on (IG) 3.3 V*
C35-2 (A2A-) - C36-12 (E1) W - BR Air fuel ratio sensor Engine switch on (IG) 3.0 V*
C37-18 (HT1B) - C36-23 (E01)
C37-13 (HT2B) - C36-23 (E01)
L-R - W-B
L - W-B
Heated oxygen sensor heater Idling Below 3.0 V
Engine switch on (IG) 11 to 14 V
C35-9 (OX1B) - C35-10 (EX1B)
C35-3 (OX2B) - C35-4 (EX2B)
G - R
B - W
Heated oxygen sensor Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor Pulse generation (see waveform 2)
C37-6 (#10) - C36-23 (E01)
C37-1 (#20) - C36-23 (E01)
C37-7 (#30) - C36-23 (E01)
C37-2 (#40) - C36-23 (E01)
C37-8 (#50) - C36-23 (E01)
C37-3 (#60) - C36-23 (E01)
L - W-B
B - W-B
R - W-B
G - W-B
Y - W-B
R - W-B
Fuel injector assembly Engine switch on (IG) 11 to 14 V
Idling Pulse generation (see waveform 3)
C35-11 (KNK1) - C35-12 (EKNK)
C35-5 (KNK2) - C35-6 (EKN2)
B - W
G - R
Knock sensor Engine speed maintained at 4000 rpm after warming up engine Pulse generation (see waveform 4)
C34-12 (VCV1) - C36-12 (E1) P-L - BR Power source for sensor (specific voltage) Engine switch on (IG) 4.5 to 5.5 V
C34-6 (VCV2) - C36-12 (E1) LG - BR Power source for sensor (specific voltage) Engine switch on (IG) 4.5 to 5.5 V
C34-10 (VV1+) - C34-11 (VV1-) R - G VVT sensor (for Intake Side of Bank 1) Idling Pulse generation
(see waveform 5)
C34-4 (VV2+) - C34-5 (VV2-) G - G-R VVT Sensor (for Intake Side of Bank 2) Idling Pulse generation
(see waveform 5)
C34-9 (EV1+) - C34-11 (VV1-) W-R - G VVT Sensor (for Exhaust Side of Bank 1) Idling Pulse generation
(see waveform 6)
C34-3 (EV2+) - C34-5 (VV2-) L - G-R VVT Sensor (for Exhaust Side of Bank 2) Idling Pulse generation
(see waveform 6)
C34-16 (NE+) - C34-17 (NE-) B - W Crankshaft position sensor Idling Pulse generation (see waveform 5)
C36-27 (IGT1) - C36-12 (E1)
C36-28 (IGT2) - C36-12 (E1)
C35-25 (IGT3) - C36-12 (E1)
C35-26 (IGT4) - C36-12 (E1)
C35-27 (IGT5) - C36-12 (E1)
C35-28 (IGT6) - C36-12 (E1)
SB - BR
R - BR
V - BR
SB - BR
GR - BR
L - BR
Ignition coil assembly (ignition signal) Idling Pulse generation (see waveform 7)
C35-23 (IGF1) - C36-12 (E1) G - BR Ignition coil assembly (ignition confirmation signal) Engine switch on (IG) 4.5 to 5.5 V
Idling Pulse generation (see waveform 7)
C37-10 (PRG) - C36-12 (E1) P - BR Purge VSV Engine switch on (IG) 11 to 14 V
Idling Pulse generation (see waveform 8)
G56-12 (SPD) - C36-12 (E1) R - BR Vehicle speed signal from combination meter assembly Driving at 20 km/h (12 mph) Pulse generation (see waveform 9)
G56-28 (STA) - C36-12 (E1) W - BR Starter signal Cranking 5.5 V or more
C34-23 (NSW) - C36-12 (E1) B - BR Starter relay control Engine switch on (IG) Below 1.5 V
Cranking 6.0 V or more
G56-35 (STP) - C36-12 (E1) V - BR Stop light switch Brake pedal depressed 7.5 to 14 V
Brake pedal released Below 1.5 V
G56-34 (ST1-) - C36-12 (E1) B - BR Stop light switch
(opposite to voltage at STP terminal)
Engine switch on (IG),
Brake pedal depressed
Below 1.5 V
Engine switch on (IG),
Brake pedal released
7.5 to 14 V
C37-19 (M+) - C36-29 (ME01) R - W-B Throttle actuator Idling with warm engine Pulse generation (see waveform 10)
C37-20 (M-) - C36-29 (ME01) G - W-B Throttle actuator Idling with warm engine Pulse generation (see waveform 11)
G55-5 (FC) - C36-12 (E1) G - BR Fuel pump control Idling Below 1.5 V
G55-4 (FPC) - C36-12 (E1) G - BR Fuel pump control Engine switch on (IG) Below 1.5 V
G55-14 (DI) - C36-12 (E1) GR - BR Fuel pump control Engine switch on (IG) 0 to 3.0 V
C36-17 (PSP) - C36-12 (E1) V - BR Power steering oil pressure sensor Engine switch on (IG) 0.3 to 4.7 V
C35-13 (VCAP) - C36-12 (E1) LG-B - BR Power source for sensor (specific voltage) Engine switch on (IG) 4.5 to 5.5 V
C35-15 (AIP) - C35-14 (EAIP) V - W-R Secondary air injection system pressure signal Engine switch on (IG) 3.0 to 3.6 V
C35-16 (AIP2) - C35-14 (EAIP) B - W-R Secondary air injection system pressure signal Engine switch on (IG) 3.0 to 3.6 V
C34-19 (AIDI) - C36-12 (E1) G - BR Diagnostic information signal for secondary air injection system Air injection system operates Pulse generation (see waveform 12)
C36-20 (AIRV) - C36-12 (E1) P - BR Air switching valve for secondary air injection system Engine switch on (IG) 11 to 14 V
C36-18 (AIRP) - C36-12 (E1) GR - BR Air pump control for secondary air injection system Engine switch on (IG) 11 to 14 V
G56-24 (AIR1) - C36-12 (E1) L - BR Air switching valve for secondary air injection system Engine switch on (IG) 11 to 14 V
G56-30 (HAI1) - C36-12 (E1) W - BR Air pump heater for secondary air injection system AI heater operating 11 to 14 V
C34-29 (ALT) - C36-12 (E1) L - BR Generator Engine switch on (IG) 11 to 14 V
G56-31 (CANH) - C36-12 (E1) LG - BR CAN communication line Engine switch on (IG) Pulse generation (see waveform 13)
G56-25 (CANL) - C36-12 (E1) W - BR CAN communication line Engine switch on (IG) Pulse generation (see waveform 14)
G56-13 (NEO) - C36-12 (E1) P - BR Engine speed signal sent to certification ECU (smart key ECU assembly) Idling with warm engine Pulse generation (see waveform 15)

for Manual Transmission
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G55-24 (BATT) - C36-12 (E1) L - BR Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
C36-23 (+BM) - C36-12 (E1) GR - BR Power source of throttle actuator Always 11 to 14 V
G56-21 (IGSW) - C36-12 (E1) W - BR Engine switch Engine switch on (IG) 11 to 14 V
G55-22 (+B) - C36-12 (E1) W - BR Power source of ECM Engine switch on (IG) 11 to 14 V
G55-23 (+B2) - C36-12 (E1) W - BR Power source of ECM Engine switch on (IG) 11 to 14 V
C35-19 (OC1+) - C35-20 (OC1-) G - L Camshaft timing oil control valve assembly (for Intake Side of Bank 1) Engine switch on (IG) Pulse generation (see waveform 1)
C34-19 (OC2+) - C34-20 (OC2-) W - R Camshaft timing oil control valve assembly (for Intake Side of Bank 2) Engine switch on (IG) Pulse generation
(see waveform 1)
C35-21 (OE1+) - C35-22 (OE1-) G - B Camshaft timing oil control valve assembly (for Exhaust Side of Bank 1) Engine switch on (IG) Pulse generation
(see waveform 1)
C34-21 (OE2+) - C34-22 (OE2-) W - L Camshaft timing oil control valve assembly (for Exhaust Side of Bank 2) Engine switch on (IG) Pulse generation
(see waveform 1)
G55-9 (MREL) - C36-12 (E1) V - BR EFI MAIN NO. 1 relay Engine switch on (IG) 11 to 14 V
C35-14 (VG) - C35-13 (E2G) W - B Mass air flow meter Idling, shift lever in P or N, A/C switch off 0.5 to 3.0 V
C35-15 (THA) - C35-7 (ETHA) Y - GR Intake air temperature sensor Idling, intake air temperature 20°C (68°F) 0.5 to 3.4 V
C36-17 (THW) - C35-8 (ETHW) R-L - W-R Engine coolant temperature sensor Idling, engine coolant temperature 80°C (176°F) 0.2 to 1.0 V
C36-13 (VCTA) - C36-14 (ETA) L - P Power source for throttle position sensor (fixed voltage) Engine switch on (IG) 4.5 to 5.5 V
C36-15 (VTA1) - C36-14 (ETA) LG - P Throttle position sensor (for engine control) Engine switch on (IG),
throttle valve fully closed
0.5 to 1.1 V
Engine switch on (IG),
throttle valve fully open
3.3 to 4.9 V
C36-16 (VTA2) - C36-14 (ETA) Y - P Throttle position sensor (for sensor malfunction detection) Engine switch on (IG),
throttle valve fully closed
2.1 to 3.1 V
Engine switch on (IG),
throttle valve fully open
4.6 to 5.0 V
G56-6 (VPA) - G56-3 (EPA) L - P Accelerator pedal position sensor (for engine control) Engine switch on (IG),
accelerator pedal released
0.5 to 1.1 V
Engine switch on (IG),
accelerator pedal fully depressed
2.6 to 4.5 V
G56-5 (VPA2) - G56-1 (EPA2) GR - W Accelerator pedal position sensor (for sensor malfunction detection) Engine switch on (IG),
accelerator pedal released
1.2 to 2.0 V
Engine switch on (IG),
accelerator pedal fully depressed
3.4 to 4.75 V
G56-4 (VCPA) - G56-3 (EPA) LG - P Power source of accelerator pedal position sensor (for VPA) Engine switch on (IG) 4.5 to 5.5 V
G56-2 (VCP2) - G56-1 (EPA2) R - W Power source of accelerator pedal position sensor (for VPA2) Engine switch on (IG) 4.5 to 5.5 V
C37-17 (HA1A) - C37-16 (E04)
C37-19 (HA2A) - C37-16 (E04)
R-L - W-B
B-W - W-B
Air fuel ratio sensor heater Idling Below 3.0 V
Engine switch on (IG) 11 to 14 V
C36-1 (A1A+) - C36-12 (E1) R -BR Air fuel ratio sensor Engine switch on (IG) 3.3 V*
C36-2 (A1A-) - C36-12 (E1) G - BR Air fuel ratio sensor Engine switch on (IG) 3.0 V*
C36-7 (A2A+) - C36-12 (E1) B - BR Air fuel ratio sensor Engine switch on (IG) 3.3 V*
C36-8 (A2A-) - C36-12 (E1) W - BR Air fuel ratio sensor Engine switch on (IG) 3.0 V*
C37-12 (HT1B) - C37-11 (E03)
C37-13 (HT2B) - C37-11 (E03)
L-R - W-B
L - W-B
Heated oxygen sensor heater Idling Below 3.0 V
Engine switch on (IG) 11 to 14 V
C34-2 (OX1B) - C34-1 (EX1B)
C34-4 (OX2B) - C34-3 (EX2B)
B - W
B - GR
Heated oxygen sensor Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor Pulse generation (see waveform 2)
C37-6 (#10) - C37-14 (E01)
C37-1 (#20) - C37-14 (E01)
C37-7 (#30) - C37-14 (E01)
C37-2 (#40) - C37-14 (E01)
C37-8 (#50) - C37-14 (E01)
C37-3 (#60) - C37-14 (E01)
L - W-B
B - W-B
R - W-B
G - W-B
Y - W-B
R - W-B
Fuel injector assembly Engine switch on (IG) 11 to 14 V
Idling Pulse generation (see waveform 3)
C35-11 (KNK1) - C35-12 (EKNK)
C35-5 (KNK2) - C35-6 (EKN2)
B - W
G - R
Knock sensor Engine speed maintained at 4000 rpm after warming up engine Pulse generation (see waveform 4)
C34-15 (VCV1) - C36-12 (E1) P-L - BR Power source for sensor (specific voltage) Engine switch on (IG) 4.5 to 5.5 V
C34-16 (VCV2) - C36-12 (E1) LG - BR Power source for sensor (specific voltage) Engine switch on (IG) 4.5 to 5.5 V
C34-9 (VV1+) - C34-10 (VV1-) R - G VVT sensor (for Intake Side of Bank 1) Idling Pulse generation
(see waveform 5)
C34-12 (VV2+) - C34-11 (VV2-) G - GR VVT Sensor (for Intake Side of Bank 2) Idling Pulse generation
(see waveform 5)
C34-13 (EV1+) - C34-14 (EV1-) W-R - R-B VVT Sensor (for Exhaust Side of Bank 1) Idling Pulse generation
(see waveform 6)
C34-18 (EV2+) - C34-17 (EV2-) L - P VVT Sensor (for Exhaust Side of Bank 2) Idling Pulse generation
(see waveform 6)
C34-6 (NE+) - C34-5 (NE-) B - W Crankshaft position sensor Idling Pulse generation (see waveform 5)
C36-24 (IGT1) - C36-12 (E1)
C36-25 (IGT2) - C36-12 (E1)
C36-26 (IGT3) - C36-12 (E1)
C36-27 (IGT4) - C36-12 (E1)
C36-28 (IGT5) - C36-12 (E1)
C35-25 (IGT6) - C36-12 (E1)
SB - BR
R - BR
V - BR
SB - BR
GR - BR
L - BR
Ignition coil assembly (ignition signal) Idling Pulse generation (see waveform 7)
C36-6 (IGF1) - C36-12 (E1) G - BR Ignition coil assembly (ignition confirmation signal) Engine switch on (IG) 4.5 to 5.5 V
Idling Pulse generation (see waveform 7)
C36-18 (PRG) - C36-12 (E1) P - BR Purge VSV Engine switch on (IG) 11 to 14 V
Idling Pulse generation (see waveform 8)
G55-18 (SPD) - C36-12 (E1) R - BR Vehicle speed signal from combination meter assembly Driving at 20 km/h (12 mph) Pulse generation (see waveform 9)
G56-10 (STA) - C36-12 (E1) W - BR Starter signal Cranking 5.5 V or more
G56-18 (STP) - C36-12 (E1) V - BR Stop light switch Brake pedal depressed 7.5 to 14 V
Brake pedal released Below 1.5 V
G55-8 (ST1-) - C36-12 (E1) B - BR Stop light switch
(opposite to voltage at STP terminal)
Engine switch on (IG),
Brake pedal depressed
Below 1.5 V
Engine switch on (IG),
Brake pedal released
7.5 to 14 V
C37-20 (M+) - C37-10 (ME01) R - W-B Throttle actuator Idling with warm engine Pulse generation (see waveform 10)
C36-29 (M-) - C37-10 (ME01) G - W-B Throttle actuator Idling with warm engine Pulse generation (see waveform 11)
G56-8 (FC) - C36-12 (E1) G - BR Fuel pump control Idling Below 1.5 V
G55-3 (FPC) - C36-12 (E1) G - BR Fuel pump control Engine switch on (IG) Below 1.5 V
G56-26 (DI) - C36-12 (E1) GR - BR Fuel pump control Engine switch on (IG) 0 to 3.0 V
C35-16 (PSP) - C36-12 (E1) V - BR Power steering oil pressure sensor Engine switch on (IG) 0.3 to 4.7 V
C35-28 (ALT) - C36-12 (E1) L - BR Generator Engine switch on (IG) 11 to 14 V
G56-32 (CANH) - C36-12 (E1) LG - BR CAN communication line Engine switch on (IG) Pulse generation (see waveform 13)
G56-31 (CANL) - C36-12 (E1) W - BR CAN communication line Engine switch on (IG) Pulse generation (see waveform 14)
C35-29 (NEO) - C36-12 (E1) P - BR Engine speed signal sent to certification ECU (smart key ECU assembly) Idling with warm engine Pulse generation (see waveform 15)

HINT:

*: The ECM terminal voltage is constant regardless of the output voltage from the sensor.



b.
U115314E01
2.95,2.016 3.414,2.153 0.464,0.138 0.447,0.165 1.131,0.367 0.684,0.202 10 5 V/DIV. 0.498,1.076 0.932,1.278 0.434,0.202 10 GND 1.478,1.918 2.378,2.120 0.900,0.202 10 1 msec./DIV.

Waveform 1

Camshaft Timing Oil Control Valve Assembly
Symbol Between OC1+ and OC1-
Between OC2+ and OC2-
Between OE1+ and OE1-
Between OE2+ and OE2-
Tester Range 5 V/DIV., 1 msec./DIV.
Condition Idling


c.
U115312E01
2.95,2.016 3.414,2.153 0.464,0.138 0.315,0.149 1.036,0.365 0.721,0.216 10 0.2 V/DIV. 0.441,1.421 0.829,1.622 0.387,0.201 10 GND 1.656,1.85 2.654,2.051 0.998,0.201 10 200 msec./DIV.

Waveform 2

Heated Oxygen Sensor
Symbol Between OX1B and EX1B
Between OX2B and EX2B
Tester Range 0.2 V/DIV., 200 msec./DIV.
Condition Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor

HINT:

In Data List, item O2S B1S2 and O2S B2S2 shows the ECM input values from the heated oxygen sensor.



d.
U115317E01
1,1.637 1.137,1.637 false 0.447,0.153 1.181,0.355 0.734,0.202 10 20 V/DIV. 0.55,1.511 1.028,1.713 0.478,0.202 10 GND 2.919,1.973 3.414,2.153 0.495,0.18 1.606,1.846 2.539,2.048 0.933,0.202 10 20 msec./DIV.

Waveform 3

Fuel Injector Assembly No. 1 (to No. 6) Injection Signal
Symbol Between #10 (to #60) and E01
Tester Range 20 V/DIV., 20 msec./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



e.
U115307E01
2.95,2.016 3.414,2.153 0.464,0.138 2.357,0.945 2.683,1.186 0.327,0.241 2.657,0.944 2.982,1.145 0.326,0.201 10 GND 2.389,0.432 2.976,0.633 0.586,0.201 10 1 V/DIV. 0.894,1.807 1.772,2.008 0.878,0.201 10 1 msec./DIV.

Waveform 4

Knock Sensor
Symbol Between KNK1 and EKNK
Between KNK2 and EKN2
Tester Range 1 V/DIV., 1 msec./DIV.
Condition Engine speed maintained at 4000 rpm after warming up engine

HINT:
·

The wavelength becomes shorter as the engine speed increases.

·

The waveforms and amplitudes displayed differ slightly depending on the vehicle.




f.
A122767E04
0.195,0.643 0.425,0.808 0.230,0.165 10 NE 0.122,1.13 0.426,1.281 0.304,0.151 10 VV1 0.126,1.512 0.425,1.657 0.299,0.145 10 VV2 2.9,0.633 3.237,0.782 0.336,0.149 10 GND 2.9,1.587 3.237,1.736 0.336,0.149 10 GND 2.9,1.204 3.237,1.353 0.336,0.149 10 GND 0.918,1.915 1.839,2.057 0.921,0.141 10 20 msec./DIV. 2.697,0.047 3.261,0.203 0.563,0.156 10 5 V/DIV.

Waveform 5

Crankshaft Position Sensor and VVT Sensor (for Intake Side)
Symbol Between NE+ and NE-
Between VV1+ and VV1-
Between VV2+ and VV2-
Tester Range 5 V/DIV., 20 msec./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine rpm increases.



g.
A122768E04
0.185,0.653 0.401,0.803 0.216,0.150 10 NE 0.122,1.118 0.403,1.266 0.281,0.149 10 EV1 0.122,1.511 0.426,1.648 0.304,0.137 10 EV2 2.889,0.646 3.221,0.793 0.332,0.147 10 GND 2.889,1.208 3.221,1.355 0.332,0.147 10 GND 2.889,1.596 3.221,1.743 0.332,0.147 10 GND 2.637,0.139 3.236,0.295 0.599,0.156 10 5 V/DIV. 0.957,1.925 1.918,2.063 0.961,0.137 10 20 msec./DIV.

Waveform 6

Crankshaft position sensor and VVT sensor (for Exhaust Side)
Symbol Between NE+ and NE-
Between EV1+ and EV1-
Between EV2+ and EV2-
Tester Range 5 V/DIV., 20 msec./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine rpm increases.



h.
A378855E01
0.188,0.521 0.5,0.708 0.313,0.188 10 false IGT 0.208,1.448 0.521,1.635 0.313,0.188 10 false IGF 2.969,1.01 3.354,1.198 0.385,0.188 10 false GND 2.969,1.875 3.354,2.063 0.385,0.188 10 false GND 2.729,0.344 3.406,0.531 0.677,0.188 10 false 2 V/DIV. 1.406,1.948 2.333,2.125 0.927,0.177 10 false 20 msec./DIV.

Waveform 7

Igniter IGT Signal (from ECM to Igniter) and Igniter IGF Signal (from Igniter to ECM)
Symbol Between IGT (1 to 6) and E1
Between IGF1 and E1
Tester Range 2 V/DIV., 20 msec./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine rpm increases.



i.
A205411E02
2.604,0.25 3.229,0.406 0.625,0.156 10 false 10 V/DIV. 0.927,1.906 1.833,2.083 0.906,0.177 10 false 20 msec./DIV. 2.677,1.073 3.042,1.25 0.365,0.177 10 false GND

Waveform 8

Purge VSV
Symbol Between PRG and E1
Tester Range 10 V/DIV., 20 msec./DIV.
Condition Idling

HINT:

If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



j.
U115313E01
2.95,2.016 3.414,2.153 0.464,0.138 0.395,0.226 1.079,0.427 0.684,0.201 10 2 V/DIV. 0.464,1.12 0.864,1.321 0.400,0.201 10 GND 1.531,1.859 2.493,2.060 0.962,0.201 10 20 msec./DIV.

Waveform 9

Vehicle Speed Signal
Symbol Between SPD and E1
Tester Range 2 V/DIV., 20 msec./DIV.
Condition Driving at 20 km/h (12 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



k.
A208000E06
2.856,0.973 3.186,1.119 0.330,0.146 10 GND 2.631,0.216 3.176,0.360 0.545,0.144 10 5 V/DIV. 0.501,0.616 0.722,0.759 0.221,0.143 10 M+ 1.237,1.806 2.058,1.964 0.820,0.158 10 1 msec./DIV.

Waveform 10

Throttle Actuator Positive Terminal
Symbol Between M+ and ME01
Tester Range 5 V/DIV., 1 msec./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



l.
A245848E04
2.849,0.99 3.182,1.142 0.333,0.151 10 GND 2.627,0.266 3.166,0.409 0.539,0.142 10 5 V/DIV. 0.479,0.626 0.664,0.777 0.184,0.15 10 M- 1.246,1.82 2.076,1.967 0.83,0.147 10 1 msec./DIV.

Waveform 11

Throttle Actuator Negative Terminal
Symbol Between M- and ME01
Tester Range 5 V/DIV., 1 msec./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



m.
A255990E01
2.962,0.998 3.299,1.147 0.337,0.149 10 GND 2.786,0.225 3.328,0.374 0.542,0.149 10 5 V/DIV. 1.2,1.789 2.096,1.938 0.896,0.149 10 50 msec./DIV.

Waveform 12

Terminal DI of Air Injection Control Driver
Symbol Between AIDI and E1
Tester Range 5 V/DIV., 50 msec./DIV.
Condition Performing system check using GTS (secondary air injection check)

HINT:

The wavelength changes when the air injection control driver detects malfunctions in the air injection system.



n.
A357201E02
2.979,1.396 3.385,1.594 0.406,0.198 10 false GND 2.76,0.292 3.323,0.479 0.563,0.188 10 false 1 V/DIV. 1.469,1.896 2.469,2.083 1,0.188 10 false 10 μsec./DIV.

Waveform 13

CAN Communication Signal
Symbol Between CANH and E1
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Engine stopped and engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



o.
A357202E02
3.01,1.354 3.385,1.531 0.375,0.177 10 false GND 2.771,0.229 3.385,0.417 0.615,0.188 10 false 1 V/DIV. 1.448,1.865 2.354,2.063 0.906,0.198 10 false 10 μsec./DIV.

Waveform 14

CAN Communication Signal
Symbol Between CANL and E1
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Engine stopped and engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



p.
A210050E16
2.833,2.396 3.167,2.552 0.333,0.156 10 false GND 1.104,2.76 1.99,2.979 0.885,0.219 10 false 2 msec./DIV. 2.229,0.302 2.771,0.594 0.542,0.292 10 false 5 V/DIV.

Waveform 15

Engine Speed Signal
Symbol Between NEO and E1
Tester Range 5 V/DIV., 2 msec./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.